Bubbled slabs can be exposed to damage or deterioration during its life. Therefore, the solution for strengthening must be provided. For the simulation of this case, the analysis of finite elements was carried out using ABAQUS 2017 software on six simply supported specimens, during which five are voided with 88 bubbles, and the other is solid. The slab specimens with symmetric boundary conditions were of dimensions 3200/570/150 mm. The solid slab and one bubbled slab are deemed references. Each of the other slabs was exposed to; (1) service charge, then unloaded (2) external prestressing and (3) loading to collapse under two line load. The external strengthening was applied using prestressed wire with four approaches, wh

An experiment was conducted in a greenhouse - research station B - College of Agricultural Engineering Sciences, University of Baghdad, during the fall season of 2018 with the aim of propagating and initially studying the field performance of 18 and 20 potential potato lines derived from Rivera and Arizona cv. after in vitro exposure of nodal segments to different dosages of gamma rays (0, 10, 20, and 30 Gray) and EMS (0, 10, 20, and 30 mM). Each control cultivar and their derived lines were independently cultured in plastic bags according to the RCBD, with three replications. The results showed that the highest plant height and number of leaves were obtained from Arizona derived lines which gave 60.11 cm and 25.30 leaves.plant-1 in

In this paper the effect of engagement length, number of teeth, amount of applied load, wave propagation time, number of cycles, and initial crack length on the principal stress distribution, velocity of crack propagation, and cyclic crack growth rate in a spline coupling subjected to cyclic torsional impact have been investigated analytically and experimentally. It was found that the stresses induced due to cyclic impact loading are higher than the stresses induced due to impact loading with high percentage depends on the number of cycles and total loading time. Also increasing the engagement length and the number of teeth reduces the principal stresses (40%) and
(25%) respectively for increasing the engagement length from (0.15 to 0

This valve is intended for use in valves for steering movement, using the qualities of the Magneto-rheological (MR) fluid to regulate the fluid, direct contact without the utilization of moving parts like a spool, a connection between electric flux, and fluid power was made, The simulation was done to employ the" finite element method of magnetism (FEMM)" to arrive at the best design. This software is used for magnetic resonance valve finite element analysis. The valve's best performance was obtained by using a closed directional control valve in the normal state normally closed (NC) MR valve, with simulation results revealing the optimum magnetic flux density in the absence of a current and the shedding condition, as well as the optimum

Recording an Electromyogram (EMG) signal is essential for diagnostic procedures like muscle health assessment and motor neurons control. The EMG signals have been used as a source of control for powered prosthetics to support people to accomplish their activities of daily living (ADLs). This work deals with studying different types of hand grips and finding their relationship with EMG activity. Five subjects carried out four functional movements (fine pinch, tripod grip and grip with the middle and thumb finger, as well as the power grip). Hand dynamometer has been used to record the EMG activity from three muscles namely; Flexor Carpi Radialis (FCR), Flexor Digitorum Superficialis (FDS), and Abductor Pollicis Brevis (ABP) with different

The national educational systems both in the Russian Federation and Iraq Republic have to adjust the training programs to duly prepare the pedagogical university students for the modern challenges and situations on the market of educational services. For success of the service, the education specialists have to fully mobilize their physical, mental and emotional resources and persistently advance their skills and knowledge using the relevant online education courses; practical research conferences; persistent self-education to master theoretical fundamentals of the modern physical education and sport service; and be active in trainings and competitions in their vocational individual game sports including badminton, table tennis and tennis.

Bovine theileriosis, caused by Theileria annulate, is disease affecting cattle and buffaloes worldwide. The current study aimed to screen the blood samples of 30 naturally suspected local buffaloes infected with Theileria species. The blood samples were initially examined by light microscopic and then the positive samples were subjected to PCR reactions. All 30 animals indicated clinical symptoms, such as high fever, loss of appetite, the presence of the hard tick, and enlargement of lymph nodes. The amplified products of 18S rRNA were analyzed, along with molecular detection of the drug-binding site alterations and interrelated changes in the cytochrome b (cyto b) gene. Blood smears revealed the presence of infected erythrocytes wi

Apium graveolens has been utilized for a multitude of purposes due to its diverse pharmacological characteristics. On the other hand, little is known about how the fatty acids (saturated and unsaturated) terpenes and steroids found in Iraqi Apium graveolens affect the human cancer cells. The purpose of this study was to examine the effects of Iraqi Apium graveolens petroleum ether extract on the human prostate cancer cell line (PC3). Subsidiary extraction and phytochemical analysis by GC/MS were performed.The dry and fresh aerial parts (leaves and stem) of Apium graveolens were extracted using a Soxhlet device with 70 % ethanol, then fractionated with petroleum ether. Then Gas Chromatography System was used to identify the bioactive

Single Point Incremental Forming (SPIF) is a forming technique of sheet material based on layered manufacturing principles. The sheet part is locally deformed through horizontal slices. The moving locus of forming tool (called as toolpath) in these slices constructed to the finished part was performed by the CNC technology. The toolpath was created directly from CAD model of final product. The forming tool is a Ball-end forming tool, which was moved along the toolpath while the edges of sheet material were clamped rigidly on fixture.

This paper presented an investigation study of thinning distribution of a conical shapes carried out by incremental forming and the validation of finite element method to evaluate the limits of the p