The present work aimed to study the efficiency of nanofiltration (NF) and reverse osmosis (RO) process for water recovery from electroplating wastewater and study the factors affecting the performance of two membrane processes. Nanofiltration and reverse osmosis membranes are made from polyamide as spiral wound module. The inorganic materials ZnCl2, CuCl2.2H2O, NiCl2.6H2O and CrCl3.6H2O were used as feed solutions. The operating parameters studied were: operating time, feed concentrations for heavy metal ions, operating pressure, feed flow rate, feed temperature and feed pH. The experimental results showed, the permeate concentration increased and water flux decreased with increase in time from 0 to 70 min. The permeate concentrations increased and flux decreased with increase in feed concentrations from 10 to 300 mg/l. Raising of pressure from 1 to 4 bar, permeate concentration decreased for RO, for NF decreased and then increased at high pressure and increase the flux. The rises of flow rate from 20 to 50 l/h decreased permeate concentration and the flux increase. The rises of temperature from 26 to 40 °C, increased permeate concentration and increased the flux. The rise in pH from 4 to 7, decreased the flux as the pH goes from acidic side towards alkaline. The polyamide nanofiltration membrane had allowed permeation of chromium and copper ions to lower than permissible limits. Nanofiltration membrane had allowed permeation of nickel and zinc ions at low concentration of these ions. The polyamide RO membrane gave a high efficiency for removal of chromium, copper, nickel and zinc and it had allowed permeation of these ions to the lower than permissible limits. The rejection at first three minutes when the feed concentration approximately was constant for chromium in NF and RO, was 99.7% and 99.93%, for copper was 98.43% and 99.33%, for zinc was 97.96% and 99.49%, and for nickel was 97.18% and 99.49% respectively. The maximum recovery for chromium in NF and RO was 71.75% and 48.5%, for copper was 75.62% and 50.68%, for zinc was 80.87% and 54.56%, for nickel was 60.06% and 46.18% respectively. For a mixture of synthetic electroplating wastewater, nanofiltration and reverse osmosis membranes have a high rejection percentage for heavy metal ions. It was obtained pure water and concentrations of less than allowable limits for heavy metals in the case of the mixture.
Colapalpus eriophyoides (Baker) attacking leaves of palm trees is redcscnbed and illustrated from Baghdad Kuwait.
Background: Salivary gland neoplasms constitute a group of heterogeneous lesions with complex clinicopathologic characteristics and distinct biological behavior. Numerous studies have suggested geographical variation, therefore the aims of this study were to analyze the characteristics of salivary gland neoplasms in two Iraqi centers and to analyze the postoperative complications that are encountered after surgical treatment of these tumors. Materials and Methods: A retrospective study of the patients who were treated for major and minor epithelial salivary gland tumors was conducted. The analyzed data included; demographic information (age and gender), the site of the tumor, the clinical manifestations, the histological type of the tumo
... Show More
(1)
Brucellosis is possess a significant public health problem in Baghdad. In this study, we investigated the potential role of the PCR assay in detection of Brucella species, from patients suspect to have brucellosis, using blood samples in both human and animal. To establish a PCR technique for diagnosis of active brucellosis in our samples, DNA extraction was carried out using a commercial kit, and a laboratory extraction procedure. PCR amplification was done using 1 set of primers: B4/B5 for Brucella species. Extraction of Brucella DNA using the commercial kit was successful. The laboratory extraction was successful and more economic. A total of 178 peripheral blood
... Show More
(1)
Physical adsorption by nitrogen gas was studied on seven commercial platinum reforming catalysts (RG-402, RG-412, RG-432, RG-451, RG 422,RG-482, PS-10), four prepared platinum catalysts (0.1%Pt/alumina, 0.2 %Pt/alumina, 0.45 %Pt/alumina and 0.55% Pt/alumina), and -alumina support. Physical adsorption was carried out by using Accelerated Surface Area and Porosimetry (ASAP 2400 device) at 77 K . The results indicate that the surface area in genaral decreases with increasing platinum percentage, high platinum loaded (0.45% and 0.55%) it was found that the percent increasing in surface area was lower than those obtained for low platinum loaded catalysts , and at very higher platinum loading 0.6 %Pt , some reduction in surface area was
... Show More
(12)
(5)
The planning, designing, construction of excavations and foundations in soft to very soft clay soils are always difficult. They are problematic soil that caused trouble for the structures built on them because of the low shear strength, high water content, and high compressibility. This work investigates the geotechnical behavior of soft clay by using tyre ash material burnt in air. The investigation contains the following tests: physical tests, chemical tests, consolidation test, Compaction tests, shear test, California Bearing Ratio test CBR, and model tests. These tests were done on soil samples prepared from soft clay soil; tyre ash was used in four percentages (2, 4, 6, and 8%). The results of the tests were; The soil samples which
... Show MoreThe process of name calling in the propaganda discourse is one of the most important methods of persuasive propaganda act, based on the ideology of working with the function, and the valuation of this function, creating a hermeneutic representation of the meaning falls within a specific format and responds to a specific function, which is the realization of the intent of the propaganda doer in persuasion and persuasion through negative and positive propaganda logic. The method of name calling has played a dangerous and horrific role in conflicts and ideological and military wars throughout history.
This study aims to find out the mechanisms of semiotics system behind discourse of propaganda far from substantive&n
... Show More
Burnishing improves fatigue strength, surface hardness and decrease surface roughness of metal because this process transforms tensile residual stresses into compressive residual stresses. Roller burnishing tool is used in the present work on low carbon steel (AISI 1008) specimens. In this work, different experiments were used to study the influence of feed parameter and speed parameter in burnishing process on fatigue strength, surface roughness and surface hardness of low carbon steel (AISI 1008) specimens. The first parameter used is feed values which were (0.6, 0.8, and 1) mm at constant speed (370) rpm, while the second parameter used is speed at values (540, 800 and 1200) rpm and at constant feed (1) mm. The results of the fatigue
... Show More
(1)