Constructing a fine 3D geomodel for complex giant reservoir is a crucial task for hydrocarbon volume assessment and guiding for optimal development. The case under study is Mishrif reservoir of Halfaya oil field, which is an Iraqi giant carbonate reservoir. Mishrif mainly consists of limestone rocks which belong to Late Cenomanian age. The average gross thickness of formation is about 400m. In this paper, a high-resolution 3D geological model has been built using Petrel software that can be utilized as input for dynamic simulation. The model is constructed based on geological, geophysical, pertophysical and engineering data from about 60 available wells to characterize the structural, stratigraphic, and properties distribution along the reservoir. Fourteen geological surfaces for all Mishrif units have been generated based on well tops data and top Mishrif structural map. The reservoir has been divided into 163 sublayers through the vertical direction and 160*383 grid cells in x-y direction with 9,988,640 total grid cells. A scale up process are performed for well log data, then, Sequential Gaussian Simulation algorithm are applied to fill 3D grid cells with properties values in areas away from wells. Pertophysical properties distribution for all reservoir zones are analyzed. The estimated initial oil in place of Mishrif through this model is close to that calculated in other previous studies.
KE Sharquie, AA Noaimi, MS Abass, American Journal of Dermatology and Venereology, 2019 - Cited by 4
In this research, the effect of reinforcing epoxy resin composites with a filler derived from chopped agriculture waste from oil palm (OP). Epoxy/OP composites were formed by dispersing (1, 3, 5, and 10 wt%) OP filler using a high-speed mechanical stirrer utilizing a hand lay-up method. The effect of adding zinc oxide (ZnO) nanoparticles, with an average size of 10-30 nm, with different wt% (1,2,3, and 5wt%) to the epoxy/oil palm composite, on the behavior of an epoxy/oil palm composite was studied with different ratios (1,2,3, and 5wt%) and an average size of 10-30 nm. Fourier Transform Infrared (FTIR) spectrometry and mechanical properties (tensile, impact, hardness, and wear rate) were used to examine the composites. The FTIR
... Show MoreOilwell cementing operations are crucial for drilling and completion, preserving the well's productive life. However, weak and permeable formations pose a high risk of cement slurry loss, leading to failure. Lightweight cement, like foamed cement, is used to avoid these difficulties. This study is focused on creating a range of foamed slurry densities and examining the effect of gas concentration on their rheological properties. The foaming agent and foam stabilizer are tested, and the optimal concentration is determined to be 2% and 0.12%, respectively, by the weight of the cement.
Furthermore, the construction of samples of foam cement with different densities (0.8, 1.0, 1.2, 1.4, and 1.6) g/cc is performed to f
... Show MoreBackground: Antimicrobial prescribing patterns have an important role in the emergence of resistance, and community pharmacists have a substantial influence on this issue. Objective: To assess community pharmacists' behaviors and attitudes toward antimicrobial dispensing, determine their proportions and categories, and examine the underlying rationales for this practice. Methods: A descriptive cross-sectional survey of community pharmacists in Iraq was conducted from June to August 2023, using a self-administered validated questionnaire. The attitudes, practices, and motivations driving the distribution of antimicrobials without a prescription (AWP) were explored in three areas. Results: A sizable proportion (61.6%) of respondents rejected
... Show MoreThe aim of the current study was to develop a nanostructured double-layer for hydrophobic molecules delivery system. The developed double-layer consisted of polyethylene glycol-based polymeric (PEG) followed by gelatin sub coating of the core hydrophobic molecules containing sodium citrate. The polymeric composition ratio of PEG and the amount of the sub coating gelatin were optimized using the two-level fractional method. The nanoparticles were characterized using AFM and FT-IR techniques. The size of these nano capsules was in the range of 39-76 nm depending on drug loading concentration. The drug was effectively loaded into PEG-Gelatin nanoparticles (≈47%). The hydrophobic molecules-release characteristics in terms of controlled-releas
... Show MoreThis research paper studies the use of an environmentally and not expensive method to degrade Orange G dye (OG) from the aqueous solution, where the extract of ficus leaves has been used to fabricate the green bimetallic iron/copper nanoparticles (G-Fe/Cu-NPs). The fabricated G‑Fe/Cu-NPs were characterized utilizing scanning electron microscopy, BET, atomic force microscopy, energy dispersive spectroscopy, Fourier-transform infrared spectroscopy and zeta potential. The rounded and shaped as like spherical nanoparticles were found for G-Fe/Cu‑NPs with the size ranged 32-59 nm and the surface area was 4.452 m2/g. Then the resultant nanoparticles were utilized as a Fenton-like oxidation catalyst. The degradation efficiency of
... Show MoreAutorías: Naji Kadhim Ali, Saleh Radhi Amish, Wameedh Shamil Kamil. Localización: Revista iberoamericana de psicología del ejercicio y el deporte. Nº. 4, 2022. Artículo de Revista en Dialnet.
Through this descriptive study of the image of the Islamic Republic of Iran in the independent Iraqi press, the researcher relies on surveys, content analysis, and observation tools. The research community selected was the Iraqi independent press, represented by the Al-Zaman, Al-Dustour, and Al-Mada newspapers. The researcher adopts the comprehensive inventory method for newspaper issues produced between October 2019 and January 2020.
The results of this study show that Iran's interference in Iraq's internal affairs was one of the most prominent components of the picture that independent Iraqi newspapers seek to paint about the Islamic Republic of Iran.
It is often needed to have circuits that can display the decimal representation of a binary number and specifically in this paper on a 7-segment display. In this paper a circuit that can display the decimal equivalent of an n-bit binary number is designed and it’s behavior is described using Verilog Hardware Descriptive Language (HDL). This HDL program is then used to configure an FPGA to implement the designed circuit.