In this work, the effect of the addition of bright nickel plating and silver carried out by the electroplating method has been studied, on the coating of copper nanoparticles on the copper base metal via the process of thermal evaporation. The improvement of the solar absorber using CuNP in combination with the bright nickel and silver was obtained to be better than copper nanoparticles individually. A bright nickel enhanced the absorbed thermal stability. Also, other optical properties, absorptions, and emissivity slightly decreased from (93% to 87%), while the existence of silver had a slight impact on absorption of about (86.50%). On the other hand, thermal conductivity was evaluated using hot disk analyzer. The results showed a good

The main focus of research is on how to achieve the internal and external dimensions of corporate social responsibility through human resources management strategies, which is a major of research aimed. The main problem of this research was confirmed, which confirms that there is an unclear role for social responsibility, lack of human resources management strategies, and ambiguity of roles in the municipality under study. The diagnose of the problem and determining the gap between the internal and external dimensions of social responsibility and human resources management was identified, which attacked the researcher's attention to navigate in this subject, look for the reasons for the gaps and try to reduce them. The case study

Laser etching may be an alternative to acid etching of enamel and dentin. Several characteristics of irradiated dental hard tissues have been considered advantageous, microscopically rough surfaces without demineralization, open dentinal tubules without smear layer production and dentin surface sterilization. The aim of this study is to determine and compare histology the microleakage in class V cavity restored with a light cured composite after conditioning the samples(tooth surface) with 1-acid etching, 2-Q-switched Nd:YAG Laser etching and finally 3- acid and laser etching. Materials and methods: Twenty four non carious human extracted teeth were used in this study. The samples were equally grouped into four groups of six teeth each.

  The research aims to know The Effect Of Flexible Grouping Strategy  and Three Step Interview strategy on achievement of the history material among student of the first literary class, The Researcher used the experimental design of the two experimental groups and the control group and with post test, researcher group (a) represent the experimental group taught according the Flexible Grouping Strategy  , and Division (c) to represent the second experimental group which studied according Three Step Interview strategy and Division (b ) to represent the control group taught in the traditional method, the number of students (99) students of (33) female students in each division. T

The aim of this work was to develop and validate a rapid and low cost method for estimation of ibuprofen in pharmaceutical suspensions using Reverse-Phase High Performance Liquid Chromatography. The proposed method was conducted and validated according to International Conference on Harmonization (ICH) requirements. The chromatographic parameters were as follows: column of octyldecylsilyl C18 with dimensions (150 × 4.6) mm, mobile phase composed of acetonitrile with phosphoric acid with a ratio of 50 to 50 each using isocratic mode, flow rate of 1.5 mL/min and injection volume of 5 μL. The detection was carried out using UV detector at 220 nm. The method was validated and showed short retention time for ibuprofen peak at 7.651 min, wit

الملاخص كامل

In the present investigation, bed porosity and solid holdup in viscous three-phase inverse fluidized bed (TPIFB) are determined for aqueous solutions of carboxy methyl cellulose (CMC) system using polyethylene and polypropylene as  a particles with low-density and diameter (5 mm) in a (9.2 cm) inner diameter with height (200 cm) of vertical perspex column. The effectiveness of gas velocity U_g , liquid velocity U_L, liquid viscosity μ_L, and particle density ρ_s on bed porosity B_P and solid holdups ε_g were determined. The bed porosity increases with "increasing gas velocity", "liquid velocity", and "liquid viscosity". Solid holdup decreases with increasing gas, liquid

The objective of the current research is to identify the effective of the suggested instructional design that based on the teaching strategy for understanding in achievement for students(girls) of mathematics in the fifth grads secondary school. To achieve the research goal, the empirical research method is depended. In this method a realistic empirical design pre-test of two equivalent sets to determine the students’ grade is used. The following zero hypotheses is formulated “There is no statistical difference for the faction at 0.05 between the mean grad for the students of the empirical group who studied the subject using the Instructional design based on the teaching strategy for understanding and those who studied the same subje

The experiment was conducted in Baghdad for study effect using mold board and disc plows as main factor , and second factor was three speeds 1.85 , 3.75 and 5.62 km / hr , and sub-second factor was three levels of soil moisture 21,18 and 14 % to determined data fuel consumption and economy costs machine unit in silt clay loam with depth 22cm. The experiment was a split – split plot arrangement in a randomized complete block design with three replications and statistical analysis using Least Significant Design 0.05 was used to compare the means of treatments. Mold board recorded least fuel consumption and cast fixed and variable and management and total costs of tractor and plow costs and total cost. Increasing forward speeds of the t

This research is an attempt to study and evaluate the maintenance function at Factory 7 - The State General Company for Leather Industries, and to design a computerized preventive maintenance system to design and to analyze preventive  maintenance.  To accomplish the objectives of this research, data were gathered and analyzed according to the reliability engineering criteria for the period 2/1– 30/6/2005, then a preventive maintenance plan was designed for each machine of the sample study using the computerized system designed in this research. A Monte Carlo Simulation methodology was used for the purpose of evaluating the performance of the preventive maintenance plan of each machine for one year. The simulation res