This research aims to measure the discrepancy between the accounting income which is prepared according to generally accepted accounting principles and the tax income that is being prepared according to the rules and tax laws, and find out the most important differences that arise between incomes.The research found the most important to the following conclusions:1.Faces determining the tax base for companies subject to income challenges related to the weakness of the efficiency and the possibility of technical angel tax and its ability to examine the financial statements submitted to the tax administration tax.2.That the tax system in Iraq does not comply with accepted accounting principles generally accepted.The research recommends the

This work focused on anthropogenic influences of the trace metals distribution in the soils of Kirkuk city. Sequential extraction technique was used to determine the distribution of the chemical fractions of Ag, Cd, Co, Cu, Ni, Pb, Zn, As, Cr and V in soil of Kirkuk city. This area is affected mainly by burning oil trash. Results show that these heavy metals were primarily restricted to surface horizons and mostly associated with the residual fraction (28.8 – 50%). The remnant fractions (13.8 – 33.1%) linked to the organic matter, 7.9 – 27.2% was bound to Fe-Mn oxide, 0.7 – 27.9 was bound to carbonate. Only a small amount of the total metals in the soil is exchangeable (0.5 – 4.2%) and water soluble (0 – 4.1%) fractions.

ABSTRACT:In this paper, Cd10–xZnxS (x = 0.1, 0.3, 0.5) films were deposited by using chemical spray pyrolysis technique, the molar concentration precursor solution was 0.15 M/L. Depositions were done at 350°C on cleaned glass substrates. X-ray dif- fraction technique (XRD) studies for all the prepared film; all the films are crystalline with hexagonal structure .The optical properties of the prepared films were studied using measurements from VIS-UV-IR spectrophotometer at wave- length with the range 300 - 900 nm; the average transmission of the minimum doping ratio (Zn at 0.1%) was about 55% in the VIS region, it was decrease at the increasing of Zn concentration in the CdS films, The band gap of the doped CdS films was varied as 3.7, 3

The effect of air injection angle on the performance of airlift pump used for water pumping has been studied analytically and experimentally. An airlift pump of dimensions 42mm diameter and 2200 mm length with conventional and modified air injection device was considered. A modification on conventional injection device (normal air-jacket type) was carried out by changing injection angle from 90  (for conventional) to 45  and 22.5  (for modified). Continuity and one-dimensional momentum balance for the flow field with basic principle of two-phase flow and expressions of slip ratio and friction factor as function of flow rates were formulated. The analytical and experimental investigations were carried out f

The success of any media work in our contemporary life is based on proper planning. Television in Iraq is like any media outlet that adopts clear planning and programming in order to achieve the goals set in the news, entertainment, education. Iraq TV relies on four programming plans in one year (short term), but we often receive central instructions directly from the Minister of Information ordering to cancel the program plan and what was scheduled for broadcast to be finally replaced by alternative or emergency program associated with an incident, occasion or important news, these programs are all called (emergency programs).

In this present research we will be dealing with these programs as well as the extent of their impact o

Since the beginning of the twentieth century, the art of composition has witnessed major transformations that accompanied the transformations that occurred in the cognitive field. The plastic artists rejected the prevailing artistic line, and sought to create a new artistic format that accommodates the new social and cultural problems. So was the announcement of the era of modernity in the late nineteenth century, with the birth of the impressionism movement that gave a place to challenge all that is familiar. . And he drew the attention of the researcher, and for that he chose the research title (Characteristics of Modernity in the Works of Saleh Al-Jumayyi (Analytical Study)) The researcher divided the research as follows:
Methodolo

The objective of this study is to determine the efficacy of class V Er:YAG laser (2940 nm) cavity preparation and conventional bur cavity preparation regarding Intrapulpal temperature rise during cavity preparation in extracted human premolar teeth. Twenty non carious premolar teeth extracted for orthodontic purposes were used and class V cavity preparation was applied both buccal and lingual sides for each tooth .Samples were equally grouped into two major groups according to cavity depth (1mm and 2mm). Each major group was further subdivided into two subgroupsof ten teeth for each (twenty cavities for each subgroup). TwinlightEr:YAG laser (2940 nm) with 500mJ pulse energy, P.R.R of 10 Hz and 63.69 J/cm2 energy density was used. The ana

 Interested in many scholars and reseachers  the subject of the media and means varied his roleinfluential in the definition of the public of issues and political, cultural, social and because of its spread wide and ability to address the people of all levels effect them  in the formation consciousness of those issues and types of this awareness is an awareness of the tax, contribute to media formation consciousness tax through the definition of people what tax and importance of the role of its revenues to supplement the state budget by posting tax laws and regulations of applied and all what respect process account tax, to be in charge of the tax familiar enough about this, which avoid being cheated taxmisleading when rev

Magnetic Abrasive Finishing (MAF) is an advanced finishing method, which improves the quality of surfaces and performance of the products. The finishing technology for flat surfaces by MAF method is very economical in manufacturing fields an electromagnetic inductor was designed and manufactured for flat surface finishing formed in vertical milling machine. Magnetic abrasive powder was also produced under controlled condition. There are various parameters, such as the coil current, working gap, the volume of powder portion and feed rate, that are known to have a large impact on surface quality. This paper describes how Taguchi design of experiments is applied to find out important parameters influencing the surface quality generated during