The infrastructure is one of the basic components of the tourism industry in Iraq in general and in Najaf in particular, in spite of there are obstacles and problems that which are hindered the development of tourism in Iraq, some of them are related to the tourism industry itself, some are related to the security and political situation, and some are related to poor management of tourism. However, the infrastructure is considered the cornerstone of the success of the tourism industry in Iraq and other countries, if it is available, it can be a potential indicator of success, and on the contrary, it is a hindrance to go forward. The aim of this research is to shed light on the availability of requirements for the success of the tourism industry as far as the infrastructure is concerned. As for the method used, it is the random horizontal survey, by distributing a questionnaire to a random sample of visitors or tourists to the city of Najaf. Although the tourism industry in Iraq has the potential to create and expand the economic activities and commercial services, and help to create new and developing urban communities. However, the tourism industry needs a kind of integrated services, which start with the qualified and trained human component, and advanced infrastructure. Overall evaluation of infrastructure services was on the basis of ranks, the first rank is average and the second rank is acceptable while the third rank was good and the fourth rank is poor. Hence, the infrastructure which is supporting the spatial development is not likely to be more than two thirds of the evaluation outside the good evaluation, or it is in the third rank as seem in the overall evaluation of the infrastructure in Najaf, this leads to a review of infrastructure planning as an important factor in the development of the tourism industry in Najaf. The local government and the private sector must invest in a kind of integrated services, which start with the qualified and trained human element and infrastructure.
Objective(s): To determine the impact of instructional intervention program upon psychological health status for
women who undergo chemotherapy after mastectomy
Methodology: The sample consisted of (100) women, (50) considered as study group, and another (50) the control
group. A pre test was done for both groups (study and control), and then the study samples were exposed to an
instructional intervention and three-dimensional post tests and the length of time between each test 21 days in
the Institute and Hospital of Radiation and Nuclear Medicine. The questionnaire composed of three parts, first,
demographic information; include (age, educational level, type of family, occupation, marital status, and adequacy
of mo
By optimizing the efficiency of a modular simulation model of the PV module structure by genetic algorithm, under several weather conditions, as a portion of recognizing the ideal plan of a Near Zero Energy Household (NZEH), an ideal life cycle cost can be performed. The optimum design from combinations of NZEH-variable designs, are construction positioning, window-to-wall proportion, and glazing categories, which will help maximize the energy created by photovoltaic panels. Comprehensive simulation technique and modeling are utilized in the solar module I-V and for P-V output power. Both of them are constructed on the famous five-parameter model. In addition, the efficiency of the PV panel is established by the genetic algorithm
... Show More
(36)
(33)
(2)
(3)
This paper presents a vibration suppression control design of cantilever beam using two piezoelectric patches. One patch was used as an actuator element, while the other was used as a sensor. The controller design was designed via the balance realization reduction method to elect the reduced order model that is most controllable and observable. the sliding mode observer was designed to estimate six states from the reduced order model but three states are only used in the control law. Estimating a number of states larger than that used is in order to increase the estimation accuracy. Moreover, the state estimation error is proved bounded. An optimal LQR controller is designed then using the estimated states with the slid
... Show More
(1)
In this paper, chip and powder copper are used as reinforcing phase in polyester matrix to form composites. Mechanical properties such as flexural strength and impact test of polymer reinforcement copper (powder and chip) were done, the maximum flexural strength for the polymer reinforcement with copper (powder and chip) are (85.13 Mpa) and (50.08 Mpa) respectively was obtained, while the maximum observation energy of the impact test for the polymer reinforcement with copper (powder and chip) are (0.85 J) and (0.4 J) respectively
In current study, the dye from flowers petals of Strelitzia reginae used for the first time to prepare natural photosensitizer for DSSC fabrication. Among five different solvents used to extract the natural dye from S. reginae flowers, the ethanol extract of anthocyanin dye revealed higher absorption spectrum of 0.757a.u. at wavelength of 454nm. A major effect of temperature was studied to increase the extraction yield. The results show that the optimal temperature was 70 °C and there was a sharp decrease of dye concentration from 0.827 at temperature of 70 °C to 0.521 at temperature of 90°C. The extract solution of flowers of S. reginae showed higher concentration in acidic media, especially at pH 4 (0.902). The
... Show More
(2)
(2)
Protection of the oil pipelineswhich extracted from the wells was found to shut the well and prevent the leakage of oil when broken using safety valve. This valve is automatically activated by loss of pressure between the well and pipelines, which take the pressure, signal from hydraulic pressure sensor through pressure control valve which has constant or variable value but it is regulated manually. The manual regulatory process requires the presence of monitoring workers continuously near the wells which are always found in remote areas. In this paper, a smart system has been proposed that work with proportional pressure control valve and also electronic pressure sensor through Arduino controller, which is programmed in a way that satisfie
... Show More