ABSTRACT:In this paper, Cd10–xZnxS (x = 0.1, 0.3, 0.5) films were deposited by using chemical spray pyrolysis technique, the molar concentration precursor solution was 0.15 M/L. Depositions were done at 350°C on cleaned glass substrates. X-ray dif- fraction technique (XRD) studies for all the prepared film; all the films are crystalline with hexagonal structure .The optical properties of the prepared films were studied using measurements from VIS-UV-IR spectrophotometer at wave- length with the range 300 - 900 nm; the average transmission of the minimum doping ratio (Zn at 0.1%) was about 55% in the VIS region, it was decrease at the increasing of Zn concentration in the CdS films, The band gap of the doped CdS films was varied as 3.7, 3

Pollen grains morphology have been studied for the wild species of the genus Erysimum L. which belong to Crucifereae family in Iraq. These species are E. filifolium Boiss. et Hausskn., E. oleifolium J. Gay, E. repandum L., E. eginense Hausskn. ex Bornm., E. aucheranum J. Gay, E. cheiranthoides L., E. alpestre Ky. ex Boiss., E. kurdicum Boiss. et Hausskn., E. tenellum DC., E. strophades Boiss., E. gladiiferum Boiss. et Hausskn., E. nasturtioides Boiss. et Hausskn. The study was performe by using light microscope . The study reveal that there was only one type of pollen grain named Tricoplate in all studied species . The study also demonstrated that there were differences among pollen grains morphology . The species E. kurdicum , E. alpestre

The effect of air injection angle on the performance of airlift pump used for water pumping has been studied analytically and experimentally. An airlift pump of dimensions 42mm diameter and 2200 mm length with conventional and modified air injection device was considered. A modification on conventional injection device (normal air-jacket type) was carried out by changing injection angle from 90  (for conventional) to 45  and 22.5  (for modified). Continuity and one-dimensional momentum balance for the flow field with basic principle of two-phase flow and expressions of slip ratio and friction factor as function of flow rates were formulated. The analytical and experimental investigations were carried out f

Numerous drilling additives and materials are used continuously because they are necessary to support and give the required properties of the drilling fluid so that to ensure the stability of the borehole. This paper aspires to evaluate the rheological properties of bentonite (montmorillonite) Trefawey as an alternative to using commercial bentonite. Monitoring and evaluating of the rheological and filtration properties were prepared. This exertion aims to focus on the effect of hematite, and barite on the rheological properties of the three aforementioned bentonite types. An improvement in the rheological properties of bentonite (montmorillonite). Trefawey was observed after adding the previous heavy materials. Hematite has by some

The aim of this research is to investigate the effect of economic, social and institutional factors on adoption within the national program for the propagation of high-rank seeds of wheat crop. 170 questionnaires were collected, 50% of them were participants in the program from Wasit and Babil governorates. Probabilistic regression models were used to know this effect, and the possibility of adopting Farmers of improved seeds produced from the national program for the multiplication of seeds of higher grades using the (ADOPT) program. The adoption rate was 0.12%, and the total number of adopters were 12 farmers, at a rate of 14.2%. Tobit model was estimated  to find out the impact of the profitability of the dunum, capital, farm si

At present, the ability to promote national economy by adjusting to political, economic, and technological variables is one of the largest challenges faced by organization productivity. This challenge prompts changes in structure and line productivity, given that cash has not been invested. Thus, the management searches for investment opportunities that have achieved the optimum value of the annual increases in total output value of the production line workers in the laboratory. Therefore, the application of dynamic programming model is adopted in this study by addressing the division of investment expenditures to cope with market-dumping policy and to strive non-stop production at work.

The reinforced fiberglass in cement slurry reflects the effect on its properties compared to usual additives. Fiberglass is typically used in cement slurry design for one or another of the following goals: (Earth earthquake, bearing storage, and with differential stresses, to enhance cement durability and increase its compressive strength). The main goal is to use glass fiber and ground fiberglass to improve the tensile strength and moderate compressive strength significantly. On the other hand, the use of glass fibers led to a slight increase in the value of thickening time, which is a desirable effect. Eleven glass fiber samples and milled glass fiber were used to show these materials' effect on Iraqi cement with (0.125, 0.25, 0.5