Background:: Infertility is a very common condition affecting approximately 13-14% of couples in the reproductive age. In general population; about 85% of couples have achieved conception within a year. Intrauterine insemination is one of the procedure which have a role in the treatment of infertile couple.Objectives:is to confirm that the use of ovulation induction in the course of intrauterine insemination elevates the pregnancy success rate.Method:This study had been conducted between December 2013 till December 2014 in AL-Elwiyah maternity hospital and AL-Samaraii hospital / Baghdad.On history and clinical examination; the chosen couple had the following criteria; primary infertility for more than one year, no previous IUI trials, husbands with normal seminal fluid analysis, wives in reproductive age group; with regular cycles of 24 – 35 days, body mass index (18-26)kg/m2, normal body contour, no galactorrhea nor hirsutism, normal uterine cavity and patent fallopian tubes by hysterosalpingography. Total number of cases is 76; had been divided into two groups who underwent IUI schedule, 38 cases preceded by ovulation induction and the other 38 cases had spontaneous ovulation by showing a single dominant Graffian follicle size of 18 mm measured by daily vaginal ultrasound.Results:During the study period; the total number of married women participated in the study were 76; divided into two groups. The first group contains 38 women who had the inclusion criteria of our research, underwent IUI after follow up and confirmed spontaneous ovulation, the second group included 38 women who also had the same inclusion criteria and underwent IUI after effective ovulation induction. 5 cases became pregnant while 33 cases didn’t conceive, while in the second group with ovulation induction; 12 cases became pregnant while the remaining 26 cases failed to conceive;Theoverall pregnancy rate was highest(31%) in the group treated with ovulation induction and intrauterine insemination in comparison with the other group which revealed a pregnancy rat.e of only (13%).Conclusion:For fertile couple in which no recognized cause for her infertility ;as for history;clinical examination and investigation are concerned, then combination of ovulation induction with intrauterine inseminationis an effective means for achieivingpregnancyrate by 31%compared with only 13%pregnancy rate in naturally ovulation cycle.
This is prospective study began in Jan. 2003 and concluded in April 2004, was undertaken to examine the benefits of 810 nm diode laser in treatment of four patient with bilateral vocal cord paralysis also to compare the results with conventional treatment Material and methods: 810 nm diode laser 15 watts was used in these cases under general anesthesia, and induction of anesthetic drug done through tracheostomy tube in all patients. All patients were decanulated “Tracheostomy tube removed”, the voice of all preserved within normal. Laser surgery in this case has more benefit and advantage than conventional methods even if the patient need more than on session of laser operation because of high success rate, less complication and easy
... Show MorePorous materials play an important role in creating a sustainable environment by improving wastewater treatment's efficacy. Porous materials, including adsorbents or ion exchangers, catalysts, metal–organic frameworks, composites, carbon materials, and membranes, have widespread applications in treating wastewater and air pollution. This review examines recent developments in porous materials, focusing on their effectiveness for different wastewater pollutants. Specifically, they can treat a wide range of water contaminants, and many remove over 95% of targeted contaminants. Recent advancements include a wider range of adsorption options, heterogeneous catalysis, a new UV/H2O
The electrocoagulation process became one of the most important technologies used for water treatment processes in the last few years. It’s the preferred method to remove suspended solids and heavy metals from water for treating drinking water and wastewater from textile, diary, and electroplating factories. This research aims to study the effect of using the electrocoagulation process with aluminum electrodes on the removal efficiency of suspended solids and turbidity presented in raw water and optimizing by the response surface methodology (RSM). The most important variables studied in this research included electrode spacing, the applied voltage, and the operating time of the electrocoagulation process. The samples
... Show MoreThis paper was aimed to study the efficiency of forward osmosis (FO) process as a new application for the treatment of wastewater from textile effluent and the factors affecting the performance of forward osmosis process.
The draw solutions used were magnesium chloride (MgCl2), and aluminum sulphate (Al2 ( SO4)3 .18 H2O), and the feed solutions used were reactive red, and disperse blue dyes.
Experimental work were includes operating the forward osmosis process using thin film composite (TFC) membrane as flat sheet for different draw solutions and feed solutions. The operating parameters studied were : draw solutions concentration (10 – 90 g/l), feed solutions concentration (5 – 30 mg/l), draw solutions flow rate (10 – 50 l/hr
A study was performed to evaluate heavy metals removal from sewage sludge using lime. The processes of stabilization using alkaline chemicals operating on a simple principle of raising pH to 12 or higher, with sufficient mixing and suitable contact time to ensure that immobilization can reduce heavy metals. A 0.157 m3 tank was designed to treat Al-Rustemeyia wastewater treatment plant sludge. Characteristics of raw sludge were examined through two parameters: pH and heavy metal analysis. Different lime doses of (0- 25) g CaO/100 g sludge were mixed manually with raw sludge in a rotating drum. The samples were analyzed two hours after mixing. pH and heavy metals results were compared with EPA and National Iraqi Stand
... Show MoreCeramic coating compose from a ceramic mixture (MgO, Al2O3) and metall (Al-Ni) were produced by Thermal Spray Technique. The mixed ratio of used materials Al:Ni (50%) and 40% of Al2O3 and 10% MgO. This mixture was spray on a stainless steel substrate of type (316 L) by using thermal spray with flame method and at spraying distances (8, 12, 16 and 20) cm, then the prepared films were treated by laser and thermal treatment. After that performing a hardness and adhesion tests were eximined. The present study shows that the best value of the thermal treatment is 1000 ℃ for 30 mint; the optimum spray distance is 12 cm and most suitable laser is 500 mJ where the microscopic and mechanical character
... Show MoreThe acrylic polymer composites in this study are made up of various weight ratios of cement or silica nanoparticles (1, 3, 5, and 10 wt%) using the casting method. The effects of doping ratio/type on mechanical, dielectric, thermal, and hydrophobic properties were investigated. Acrylic polymer composites containing 5 wt% cement or silica nanoparticles had the lowest abrasion wear rates and the highest shore-D hardness and impact strength. The increase in the inclusion of cement or silica nanoparticles enhanced surface roughness, water contact angle (WCA), and thermal insulation. Acrylic/cement composites demonstrated higher mechanical, electrical, and thermal insulation properties than acrylic/silica composites because of their lowe
... Show MoreAbstract:
This research sheds light on the major sins (fornication and sodomy) as two crimes that are prohibited by the divine laws, including its conclusion by the Islamic Sharia. Major sins so that life and the universe are organized, and the individual lives a life of chastity and purity free of filth and filth. The Islamic message included a set of preventive measures and remedial methods that, if the ummah were to apply them, they would live a decent life full of noble goals.
KE Sharquie, AA Noaimi, SA Galib, Journal of Cosmetics, Dermatological Sciences and Applications, 2013 - Cited by 4