This research discusses one of the largest and most important issues of a doctrinal and philosophical dimension at the same time, which is the issue of man’s freedom to choose his actions, and thus his responsibility for those actions, by looking at the nature of these acts, their being and the origin of their creation. He showed that they were created in man by force, and that he was their original creator, and that they were among the creatures of the God Almighty God like others, but they are attributed to man through acquisition. So to the first saying went Jahmiyya or Jabariyya, and to the second saying went to fatalism in the past, and the existentialists shared with them in the modern era, and to the third saying went to the Sunnis and the community, as the research shows
The aim of this research is to apply the concept of total value management to improve the process design of producing the toothpaste in Al Mammon factory one of the in the general company of food industry. The concept of total value management is concerning with achieve more than one values which are important for the customers as these values are related to the customers satisfaction. The research problem is that the factory did not measure the effectiveness of process design as this company has weakness in analyzing this effectiveness in synchronies with total value management. On the other side, the company did not give more attention to the cost of products and selling prices within the value cost/ profit which is one of the
... Show MoreThrough an experimental program of eighteen specimens presented in this paper, the bond strength between reinforcing bar and rubberized concrete was produced by adding waste tire rubber instead of natural aggregate. The fine and coarse aggregate was replaced in 0%, 25%, and 50% with the small pieces of a waste tire. Natural aggregate replacement ratio, rebar size, embedded rebar length, the rebar yield stress of rebar, cover, and concrete compressive strength were studied in this investigation. Ultimate bond stress, bond stress-slip response, and failure modes were presented. The experimental results reported that a reduction of 19% in bond strength was noticed in 50% replaced rubberized concrete compared with convention
... Show More
In this research thin films from SnO2 semiconductor have been prepared by using chemical pyrolysis spray method from solution SnCl2.2H2O at 0.125M concentration on glass at substrate temperature (723K ).Annealing was preformed for prepared thin film at (823K) temperature. The structural and sensing properties of SnO2 thin films for CO2 gas was studied before and after annealing ,as well as we studied the effect temperature annealing on grain size for prepared thin films .
Electrochemical Machining is a term given to one of nontraditional machining that uses a chemical reaction associated with electric current to remove the material. The process is depending on the principle of anodic dissolution theory for evaluating material removal during electrochemical process. In this study, the electrochemical machining was used to remove 1 mm from the length of the a workpiece (stainless steel 316 H) by immersing it in to electrolyte (10, 20 and 30 g) of NaCl and Na2SO4 to every (1 litter of filtered water). The tool used was made from copper. Gap size between the workpiece and electrode is (0.5) mm. This study focuses on the effect of the changing the type and concentration of electroly
... Show More
(12)
(10)
Constitute the relationship between the director and actor mainstay chock done to show art in film and television , both of which occupy what a big role in the mission accomplishment . The leadership of the director of the artwork in various joints require two features two important ( creativity and administration ) , The capabilities director of creative serves as an added intellectual and aesthetic saturated sensation that leaves its impact on all the technical elements involved in done. Either trait administration and leadership it is what requires multiple skills in dealing on according to technical standards and moral and humanitarian allow the transfer of ideas , concepts and visions to those elements to embody and implement the ki
... Show More
A case-control study was designed to find out the association between rs2234671 polymorphism of cxcr1 and rUTI in a sample of Iraqi women by polymerase chain reaction- sequence-specific primer (PCR-SSP) method. The current findings revealed that the genotype GC (OR= 7.86, 95% CI = 2.82-21.87, P= 7.7 × 10-5) and the C allele (OR= 3.93, 95% CI = 1.97 - 7.83, P = 9.8×10-5) are significantly associated with rUTI. However, the genotype GG played as a protective factor (OR= 0.12, 95% CI = 10.05 - 0.34, P = 4.0 ×10-5). Depending on these findings, the genotype GC is significantly associated with rUTI.
(4)
(2)
Breast cancer is the most commonly diagnosed cancer and remains one of the main reasons of cancer-related mortality in women worldwide. KRAS variant rs61764370 (T>G) is associated with an increased risk of occurrence of many cancers, Here The case-control study was accomplished on 135 women including 45 women with breast cancer patients, 45 women with benign breast lesions and 45 healthy women to analyze the association of KRAS variant rs (61764370 T>G) with breast cancer. LCS 6 variant in KRAS gene was amplified by using specific primers, then genotype was detected after sequencing the PCR products. The results showed that the genotype and allele frequency of TT and GT allele of KRAS
... Show More
(4)
(1)
Children who have a health problem need special requirements for their clothes. The purpose of the study is to design functional and aesthetic clothes to meet their needs. The research used the applied descriptive approach. The research sample comprised 120 women whose children suffered from hip dislocation. Designs for injured children presented and submitted to the arbitrators for evaluation regarding the functional and aesthetic aspects. The finding was achieving the design solutions. The most important recommendations are to increase attention to designing clothes to suit all the needs of society.