Abstract

Personality is one of the most important elements that should be developed in university student. Thus, we have to develop the positive traits and neutralize the negative traits of students as well as we have to pay attention to the level of student achievement at the same time, the researcher designed a scale to measure the traits of study sample. The research come out with a number of recommendations and proposals, the most important of which Enhancing the positive characteristics of university students in order to reach them to the level of mature personality with mental health. Enhancing the positive role of the high level of achievement by motivating the stude

The current research deals with the specificity of the interior design of the classes of art education in the schools of excellence for the province of Muthanna and its center of the city of Samawah. In the first chapter، the problem of research was determined by the lack of internal spaces of the classes of art education to designs that meet the requirements and needs of students in these educational stages.  The importance of the research in being an addition to knowledge in the field of interior design and engineering department of the general directorates of the Ministry of Education. The objectives of the research were determined through.

1. Identifying the reality of the halls of art education for sch

The research, whose goal was to study students' failure in secondary school in Iraq, found that 50% of the Iraqi governorates achieved the lowest student failure rates, and Baghdad governorate had the highest percentage of repeaters. And that half of the provinces in Iraq have males constitute 70% of the repeaters, and failure in the exam represented 79.7% of the reasons for failure, and that half of the students who failed are confined to the first and third intermediate grades at a rate of 51.9% , and the research revealed that the security instability was the most influential factor in Students fai

     Equilibrium and rate of mixing of free flowing solid materials are found using gas fluidized bed. The solid materials were sand (size 0.7 mm), sugar (size0.7 mm) and 15% cast iron used as a tracer. The fluidizing gas was air with velocity ranged from 0.45-0.65 m/s while the mixing time was up to 10 minutes. The mixing index for each experiment was calculated by averaging the results of 10 samples taken from different radial and axial positions in fluidized QVF column 150 mm ID and 900 mm height.

     The experimental results were used in solving a mathematical model of mixing rate and mixing index at an equilibrium proposed by Rose. The results show that mixing index increases with inc

This study explores the barriers to adopting green environmental criteria in Supplier Selection (SS) within the Iraqi food industry. It aims to enhance the understanding of sustainable supply chain management in developing nations, with a particular focus on the Iraqi context. A case study approach was utilized to identify eleven key green environmental criteria and 54 sub-criteria, alongside seven major barriers to their adoption. The Best–Worst Method (BWM) was employed to rank the criteria, and Fuzzy Stepwise Weight Assessment Ratio Analysis (SWARA) was used to prioritize the barriers. The analysis revealed that Environmental Management Systems are the most critical criterion for SS. On the other hand, legislation and policies emerged

Sliding Mode Controller (SMC) is a simple method and powerful technique to design a robust controller for nonlinear systems. It is an effective tool with acceptable performance. The major drawback is a classical Sliding Mode controller suffers from the chattering phenomenon which causes undesirable zigzag motion along the sliding surface. To overcome the snag of this classical approach, many methods were proposed and implemented. In this work, a Fuzzy controller was added to classical Sliding Mode controller in order to reduce the impact chattering problem. The new structure is called Sliding Mode Fuzzy controller (SMFC) which will also improve the properties and performance of the classical Sliding Mode control

In Iraq, water shortages and drought, especially during the hot summer months, necessitates that municipal authorities adopt water reuse projects like reusing treated domestic wastewater for crop irrigation. This work gives the conceptual and basic design elements for the necessary steps of filtration, UV irradiation and chlorination to make such a wastewater fit for agricultural use. A typical rural community of 50,000 people is considered as an example case for which functionality and relative simplicity of the proposed designs are prime factors. The objectives are 1) to show what is required and 2) that the presented information may be utilized to embark on the following phases of detailed design and execution of such projects.

The aim of this research is to design and construct a semiconductor laser range finder
operating in the near infrared range for ranging and designation. The main part of the range finder is the
transmitter which is a semiconductor laser type GaAs of 0.904 mm wavelength with a beam expander,
and the receiver with its collecting optics. The characteristics of transmitter pulse width were 200ns and
threshold current 10 Amp. and maximum operating current 38 Amp. The repetition rate was set at 660 Hz
and maximum output power about 1 watt. The divergence of the beam was 0.268o. A special computer
code was used for optimum optical design and laser spot size analysis and for calculation of atmosphere
attenuation.

Objective: In this work we design and evaluate a bidirectional pneumatic soft actuator made from silicone rubber (RTV2 C10) for the use in prosthetic hand. The actuator aimed to enhance flexibility and provide motion in two directions that mimic the actions of the human fingers. Materials and Methods: Two parallel air chambers are used in the actuator design where each chamber is divided into smaller internal cavities. These chambers are linked through a narrow connecting channel. The fabrication process relied on a molding technique based on 3D printed molds. Three separate mold components were designed and printed to allow accurate casting of silicone rubber into the desired shape. The completed actuators were then tested using an experim