Background: Temporomandibular joint disorders refer to a group of heterogeneous pain and dysfunction conditions involving the masticatory system, reducing life quality of the sufferers. Arthrocentesis is simple and less invasive surgical procedure for the treatment of internal derangement than arthroscopy and better than other conservative procedures such as drugs, occlusal appliances and physiotherapy. The aim of the study was to evaluate the effect of arthrocentesis with injection of hyaluronic acid in the treatment of internal derangement of temporomandibular joint for the restoration of its function, reducing pain and preventing further deterioration of the temporomandibular joint dysfunction. Materials and methods: This study was performed in Al-Sheed Ghazi Al-Hariri Hospital, Department of Oral and Maxillofacial Surgery, from November 2012 to October 2013, included 60 patients, aged 18 to 45 years with symptoms of temporomandibular joint pain, clicking during function and limited mouth opening. Temporomandibular joint internal derangement was assessed with clinical examination and confirmed with computed tomography scan. Arthrocentesis was done with insertion of two 18 gauge needles in the upper joint compartment, lavaged with ringer’s lactate solution and at the end of the procedure 1ml of hyaluronic acid was injected. Intensity of temporomandibular joint pain was assessed using visual analog scale, maximum mouth opening was assessed with ruler scale and joint clicking was assessed clinically by stethoscope and manual palpation. All the parameters were measured before the procedure then 1 and 3 months later. Results: During 4 months follow-up, clinical examination and comparison of the results showed reduction in pain with success rate 95%, improvement in mouth opening with success rate 100% and clicking disappeared in 95% of patients. Conclusion: The technique of arthrocentesis using Sodium Hyaluronate injection, used in patients who presented with internal derangement, showed therapeutic benefits, simplicity, safety, patients acceptance of the technique and lack of significant side effects and complications.
The inhibitive power of Polyvinyl Alcohol (PVA) was investigated toward the corrosion of carbon steel in 0.2N H2SO4 solution in the temperature range of 30-60˚C and PVA concentration range of 150-2000 ppm.
The corrosion rate was measured using both the weight loss and the electrochemical techniques. The weight loss results showed that PVA could serve as a corrosion inhibitor but its inhibition power was found to be low for the corrosion of carbon steel in the acidic media. Electrochemical analysis of the corrosion process of carbon steel in an electrochemical corrosion cell was investigated using 3-Electrode corrosion cell. Polarization technique was used for carbon steel corrosion in 0.2N H
(2)
(16)
(13)
(10)
(10)
Chlorine disinfection is a globally used method to ensure the safety of drinking water. However, it has not always been successful against viruses and, therefore, it is important to find new methods to disinfect water. Seventeen different coliphages were isolated from the treated municipal wastewater. These coliphages and MS2 were treated with different dosages of chlorine in drinking water, and a combined chlorine/ultraviolet irradiation treatment for the chlorine-resistant coliphages. Chlorine disinfection with 0.3–0.5 mg/L total chlorine (free Cl-dosage 0.12–0.21 mg/L) for 10 min achieved 2.5–5.7 Log10-reductions for 11 sensitive coliphages. The six most resistant coliphages showed no reduction with these chlorine concentra
... Show More
(36)
(37)
(43)
(36)
(2)
(1)
Sansevieriatrifasciata was studied as a potential biosorbent for chromium, copper and nickel removal in batch process from electroplating and tannery effluents. Different parameters influencing the biosorption process such as pH, contact time, and amount of biosorbent were optimized while using the 80 mm sized particles of the biosorbent. As high as 91.3 % Ni and 92.7 % Cu were removed at pH of 6 and 4.5 respectively, while optimum Cr removal of 91.34 % from electroplating and 94.6 % from tannery effluents was found at pH 6.0 and 4.0 respectively. Pseudo second order model was found to best fit the kinetic data for all the metals as evidenced by their greater R2 values. FTIR characterization of biosorbent revealed the presence of carboxyl a
... Show More
(2)
(2)
(2)
(2)