Background: The association between facial types and dental arches forms has considerable implications in orthodontic diagnosis and treatment planning. The aim was to establish the maxillary and mandibular dental arches width and length in skeletal and dental class II division 1 and class III malocclusion groups, find out the most frequent dental arch form and facial type and the association between them and to check the gender differences. Materials and Methods: Frontal and lateral facial photographs and maxillary and mandibular occlussal photographs for 90 iraqi subjects with age 18-25 years old (45 males and 45 females) divided equally into three groups, the 1st group with class II division 1malocclusion (overjet more than 3mm but less than or equal to 6mm), the 2nd group with class II division 1malocclusion (overjet more than 6mm) while the 3rd group with class III malocclusion (edge to edge or reverse overjet).Six linear measurements for each maxillary and mandibular dental cast photographs and two liner measurements for frontal and profile facial photographs was analyzed with (AUTO CAD 2013), which simplified the analyzing process and reduced the time and effort spent on taking measurements directly from the records to facilitate work and to gain more accurate results. Results: All the mean value of dental arches and facial measurements were higher in male than female, the most frequent maxillary and mandibular dental arch form in the three groups was the mid arch form follow by the narrow then the wide arch form except in the mandibular dental arch of the 3rd group it follow by the wide then the narrow arch form.The most frequent facial type in the 1st group is the Mesoprosopic one,followed by the Leptoprosopic then the Euryprosopic face type while in the 2nd and 3rd group the most frequent facial type is the Leptoprosopic, follow by the Mesoprosopic then the Euryprosopic facial type. An association was found between mid arch form and the Mesoprosopic face type in the 1st group, while no clear association was found between dental arch form and facial type in the 2nd and 3rd group for both genders. Conclusions: It was concluded that there was an association between facial type and dental arch form in subject with class II division 1malocclusion (overjet not more than 6mm), while in subject with class II division 1malocclusion (overjet more than 6mm) or with class III malocclusion (edge to edge or reverse overjet) no clear association was found between dental arch form and facial type.
(6)
(6)
(170)
(138)
This paper proposes and tests a computerized approach for constructing a 3D model of blood vessels from angiogram images. The approach is divided into two steps, image features extraction and solid model formation. In the first step, image morphological operations and post-processing techniques are used for extracting geometrical entities from the angiogram image. These entities are the middle curve and outer edges of the blood vessel, which are then passed to a computer-aided graphical system for the second phase of processing. The system has embedded programming capabilities and pre-programmed libraries for automating a sequence of events that are exploited to create a solid model of the blood vessel. The gradient of the middle c
... Show More
(1)
(1)
(1)
(11)
(7)
(16)
(16)
In this study, a new technique is considered for solving linear fractional Volterra-Fredholm integro-differential equations (LFVFIDE's) with fractional derivative qualified in the Caputo sense. The method is established in three types of Lagrange polynomials (LP’s), Original Lagrange polynomial (OLP), Barycentric Lagrange polynomial (BLP), and Modified Lagrange polynomial (MLP). General Algorithm is suggested and examples are included to get the best effectiveness, and implementation of these types. Also, as special case fractional differential equation is taken to evaluate the validity of the proposed method. Finally, a comparison between the proposed method and other methods are taken to present the effectiveness of the proposal meth
... Show More
(8)
(2)
In this work, the photodetection performance of polyvinyl alcohol (PVA) nanofibers and its composite with yttrium oxide (Y2O3) at different concentrations (2.5, 5, 10) wt% are examined deposited on p-type Si with (111) orientation. Electrospinning technique was used to create nanofiber composites. Adding Y2O3 significantly impacts the PVA nanofibers where ultraviolet-visible (UV-Vis) spectroscopy optical absorption energy gap decreases with increased concentration (2.8, 2.6, and 2.3) eV. X-ray diffraction was used to investigate crystal structure, which is cubic structure. The chemical composition study was conducted using Fourier transform infrared spectroscopy (FTIR) spectra, which revealed the stretching vibrations related to the Y-O bon
... Show More
(2)
(1)
Increasing the power conversion efficiency (PCE) of silicon solar cells by improving their junction properties or minimizing light reflection losses remains a major challenge. Extensive studies were carried out in order to develop an effective antireflection coating for monocrystalline solar cells. Here we report on the preparation of a nanostructured cerium oxide thin film by pulsed laser deposition (PLD) as an antireflection coating for silicon solar cell. The structural, optical, and electrical properties of a cerium oxide nanostructure film are investigated as a function of the number of laser pulses. The X-ray diffraction results reveal that the deposited cerium oxide films are crystalline in nature and have a cubic fluorite. The field
... Show More
(3)
(4)
The electrospun nanofibers membranes have gained considerable interest in water filtration applications. In this work, the fabrication and characterization of the electrospun polyacrylonitrile-based nonwoven nanofibers membrane are reported. Then, the membrane's performance and antifouling properties were evaluated in removing emulsified oil using a cross flow filtration system. The membranes were fabricated with different polyacrylonitrile (PAN) concentrations (8, 11, and 14 wt. %) in N, N-Dimethylformamide (DMF) solvent resulted in various average fiber sizes, porosity, contact angle, permeability, oil rejection, and antifouling properties. Analyses of surface morphology of the fabricated membranes before and after oil removal revealed
... Show More
(15)
(6)