Background: Whey protein is the green-yellow colored, liquid portion of the milk, and it is also called the cheese serum, it is obtained after the separation of curd, during the coagulation of the milk. It contains a considerable amount of α-helix pattern with an evenly distributed hydrophobic and hydrophilic as well as basic and acidic amino acids along with their polypeptide chain. The major whey protein constituents include β-lactoglobulin (β-LG),α-lactalbumin (α-LA), immunoglobulins (IG), bovine serum albumin (BSA), bovine lactoperoxidase (LP), bovine lactoferrin (BLF) and minor amounts of a glycol macro peptide (GMP). Osseointegration can be defined as a process that is immune driven which leads to the formation of the new bone surrounding the surface of the implant rather than a pure response of the bone. Titanium can activate a balance recognized to be tolerogenic with a peri-implant tissue leading to a "foreign body equilibrium (FBE)" response. Materials and methods: Twelve adult male white New Zealand healthy rabbits were used in this study, the animals were divided into two groups according to the time of scarification as follows; 2 and 6 weeks after the implantation (6 rabbits will be sacrificed for each group). Results: Statistical analysis showed that there is a highly significant difference in all parameters between the experimental group and control group at 2 weeks and 6 weeks periods. Histological results at 2 weeks period showed thread formation in whey protein and control group, distribution of osteocyte cells and osteoblast was higher in whey protein, and the bone trabecular area was also larger in whey protein groups but at 6 weeks showed mature bone in whey protein groups while in control group still woven bone. Conclusions: Whey protein is an effective in osseointegration because it enhances bone formation.
The cement slurry is a mixture of cement, water and additives which is established at the surface for injecting inside hole. The compressive strength is considered the most important properties of slurry for testing the slurry reliability and is the ability of slurry to resist deformation and formation fluids. Compressive strength is governed by the sort of raw materials that include additives, cement structure, and exposure circumstances. In this work, we use micro silica like pozzolanic materials. Silica fume is very fine noncrystalline substantial. Silica fume can be utilized like material for supplemental cementations for increasing the compressive strength and durability of cement. Silica fume has very fine particles size less
... Show MoreThe third most ordinarily cancer type diagnosed in male and is Colorectal cancer (CRC) and it is widely spread in developed countries. Most of CRC arises from development of adenomatous polyps. The current study aimed to determine whether serum retinol binding protein 4 (RBP4) and Nesfatin-1 can be used as a novel biomarker for diagnosis of CRC. Nesfatin-1, RBP4 and Thyroid Hormones (T3, T4 and TSH) levels were measured in fifty sera of male patients suffering from CRC before chemotherapy initiation treatment as G1, G2 after first chemotherapy cycle dose and G3 after second chemotherapy cycle dose compared with twenty five male volunteers as a control G4. The results showed a significant increased in RBP 4 concentration in G3 and a signific
... Show MoreIn this study, aromatic polyamide reverse osmosis membranes were used to remove zinc ions from electroplating wastewater. Influence of different operating conditions such as time, zinc concentration and pressure on reverse osmosis process efficiency was studied. The experimental results showed, concentration of zinc in permeate increase with increases of time from 0 to 70 min, and flux of water through membrane decline with time. While, the concentrations of zinc in permeate increase with the increase in feed zinc concentration (10–300 mg/l), flux decrease with the increment of feed concentration. The raise of pressure from 1 to 4 bar, the zinc concentration decreases and the flux increase. The highest recovery percentage was fou
... Show MoreIn this study, aromatic polyamide reverse osmosis membranes were used to remove zinc ions from electroplating wastewater. Influence of different operating conditions such as time, zinc concentration and pressure on reverse osmosis process efficiency was studied. The experimental results showed, concentration of zinc in permeate increase with increases of time from 0 to 70 min, and flux of water through membrane decline with time. While, the concentrations of zinc in permeate increase with the increase in feed zinc concentration (10–300 mg/l), flux decrease with the increment of feed concentration. The raise of pressure from 1 to 4 bar, the zinc concentration decreases and the flux increase. The highest recovery percentage was found is 54.
... Show MoreThe present project involves photodegrading the dye solochrom violet under advanced oxidation techniques at (25 oC) temperature and UV light. Zinc Oxide (ZnO) and UV radiation at a wavelength of 580 nm were used to conduct the photocatalytic reaction of the solochrom violet dye. One of the factors looked into was the impact of the starting conditions. pH, the amount of original hydrogen peroxide, and the dye concentration time radiation were used. For hours, the kinetics and percentages of degradation were examined at various intervals. In general, it has been discovered that the photodegradation rates of the dye were greater when H2O2 and ZnO were combined with UV light. The best wavelength to use was determined. Modern oxidation techni
... Show MoreAbstract
Lightweight materials is used in the sheet metal hydroforming process, because it can be adapted to the manufacturing of complex structural components into a single body with high structural stiffness. Sheet hydroforming has been successfully developed in industry such as in the manufacturing of the components of automotive.The aim of this study is to simulate the experimental results ( such as the amount of pressure required to hydroforming process, stresses, and strains distribution) with results of finite element analyses (FEA) (ANSYS 11) for aluminum alloy (AA5652) sheets with thickness (1.2mm) before heat treatm
... Show More