The research topic dealt with the strategic recovery of the insurance service, which is one of the approaches that have an important role in providing solutions and remedies for the recession that affects companies and hinders them from achieving their strategic goals. The research also addressed the strategic objectives of the company as the rationale and actual guide for companies of all activities in order to protect their systems from deviation for its desired purpose. So the aim of the research is to demonstrate the repercussions of the strategic recovery of the insurance Service represented by (compensation, speed of response, apology, initiative (identifying the problem). The company's strategic goals are represented (prof

The current research is concerned with methods of formation and their effect on the sintering process of ceramic materials. The research is divided into a number of chapters. The first chapter addressed the research structure (the research problem, importance, objective, limits, and it also defined the terms used in the research). The second chapter addressed the theoretical framework, where the theoretical framework has been divided into three sections. The first section dealt with methods of formation of ceramic materials including: Plasticizing method 2- semi-dry pressing method 3- dry pressing method 4- extrusion method 5- casting method.
The researcher found that there is a clear difference between the methods through her formati

The purpose of this study is designate quenching and tempering heat treatment by using Taguchi technique to determine optimal factors of heat treatment (austenitizing temperature, percentage of nanoparticles, type of base media, nanoparticles type and soaking time) for increasing hardness, wear rate and impact energy properties of 420 martensitic stainless steel. An (L₁₈) orthogonal array was chosen for the design of experiment. The optimum process parameters were determined by using signal-to-noise ratio (larger is better) criterion for hardness and impact energy while (Smaller is better) criterion was for the wear rate. The importance levels of process parameters that effect on hardness, wear rate and impact energy propertie

In this work, the effect of partial amounts of gases in gas mixture of a CW CO2 laser on the output power was investigated. Also their effect on the condition determining the glow-discharge self-sustaining required for pumping the active medium was studied. Two fit relations were derived to predict the output laser power and the electric field to unit pressure ratio as functions to the partial amounts of gases. Results presented in this work could be used fruitfully to determine some of the optimum operational conditions of glow-discharge low-power CW CO2 lasers.

Carbon nanoparticles are prepared by sonication using carbon black powder. The surface morphology of carbon black (CB) and carbon nanoparticles (CNPs) is investigated using scanning electron microscopy (SEM). The particles size ranges from 100 nm to 400 nm for CB and from 10 nm to 100 nm for CNPs. CNPs and CB are mixed with silicon glue of different ratios of 0.025, 0.2, 0.05, and 0.1 to synthesis films. The optical properties of the prepared films are investigated through reflectance and absorbance analyses. The ratio of 0.05 for CNPs and CB is the best for solar paint because of its higher solar water heater efficiency and is then added to the silicon glue . Temperature of cold water and temperature of hot water in storage tank were ta

Abstract

In this work, diabetic glucose concentration level control under disturbing meal has been controlled using two set of advanced controllers. The first set is sliding mode controllers (classical and integral) and the second set is represented by optimal LQR controllers (classical and Min-, ax). Due to their characteristic features of disturbance rejection, both integral sliding mode controller and LQR Minmax controller are dedicated here for comparison. The Bergman minimal mathematical model was used to represent the dynamic behavior of a diabetic patient’s blood glucose concentration to the insulin injection. Simulations based on Matlab/Simulink, were performed to verify the performance of each controll

This study aims to clarify areas of using information technology in accounting and its impact on the profession of auditors by reviewing the concept, types, areas and the importance of information technology and its implications on the audit profession as well as to clarify the extent of contribution of information technology in  developing of procedures of the audit profession and what its requirement, also this study aims to enhance the theoretical side by identifying the views of a sample of auditors in  Arab countries selected (Iraq, Syria, Jordan), for the extent of using of information technology in their work and level of their perception for the importance of that

Abstract

      The goal of current research to describe and diagnose the level of attention of doctors to design and regulatory dimensions, (strategic vision, organizational structure, organizational processes, business systems, personnel), and the performance of hospitals and dimensions, in six hospitals in medicine and selected a sample for research, as well as identify organizational design effect in the performance of hospitals and dimensions (efficiency, the development of human resources, patient satisfaction, achieve financial results, quality of health care).

 Research has focused in part theoretical on key variables to look organizational des

ان المشكلة البحثية تتحدد في ان المهام والادوات التي تملكها السلطة التنفيذية، من الصعوبة تركها من دون رقابة، والرقابة والتقييد ياتي من اطراف عدة، واهمها: السلطة التشريعية، فالبرلمان في العراق منح اختصاصات للنظر في اعمال واداء السلطة التنفيذية بما يضمن تقيدها بالدستور الاتحادي. والهدف من هذا البحث هو الاشارة الى اهمية الاختصاصات الممنوحة للبرلمان العراقي، بما يضمن التاسيس لدولة القانون، اي وجود مرجعية قانو

The auditor plays a key role in economic life because of the confidence his report adds to the audited financial statements. In applying the various stages of the audit process, the auditor must maintain a high moral level that determines his type of commitment in his professional behavior before God first, And to the society at last in a way that supports its independence. On this basis, the aim of the research is to identify the threats that affect the independence of the auditor. To achieve the objective of the research, the hypothesis that there is a statistically significant relationship between the threats facing the auditor and his professional independence was formulated. In the light of testing the hypotheses of research it was