Preferred Language
Articles
/
ijcpe-782
Experimental Study for Assessment of Cutting Density Effect on Hole Cleaning Efficiency in Inclined and Horizontal Wells
...Show More Authors

The poor hole cleaning efficiency could causes many problems such as high torque, drag, poor hydraulics and pipe stuck. These inherent problems result in an avoidable high operation cost which this study tried to address.  In this study, the effect of cutting density on hole cleaning efficiency in deviated and horizontal wells was investigated. Experiments were conducted using 40 feet (12 m) long of flow loop made from iron and PVC. However, the test section was made from PVC with (5.1m) long and (4” ID) for outer pipe and (2” OD) inner pipe. The cutting transport ratio (CTR) was determined from weight measurements for each test. Cutting Transport Ratio has been investigated for effects of the following parameters; flow rate, cutting size and density, yield point of drilling mud, and inclination angle. Once the setup was positioned at the desired inclination, the cutting was transported for 3 minutes at a constant flow rate and yield point. The amount of cutting removed during each test was thereafter weighted to determine cutting transport ratio CTR.

The results obtained from this study showed that the cutting density has a slight to moderate effect on hole cleaning efficiency. Also, there was a remarkable improvement in the cutting transport ratio annular velocity and hole inclination angle was increased. However, the yield point (Yp) was negligible at maximum values of annular velocity. Therefore, at high value of yield point the cuttings with large and medium size were transported more than small size. This case is inversed at a low value of Yp. Moreover, for all sizes the heavy cutting transport less than light cutting. Finally, the critical angle was recorded between 65o-75o. Sigma plot 12.5 program has been used to graph all figures in this paper.

Crossref
View Publication Preview PDF
Quick Preview PDF
Publication Date
Fri Mar 30 2012
Journal Name
Iraqi Journal Of Chemical And Petroleum Engineering
Numerical Analysis of Laminar Natural Convection in Square Enclosure with and without Partitions and Study Effect of pPartition on the Flow Pattern and Heat Transfer
...Show More Authors

The problem of steady, laminar, natural convective flow in an square enclosure with and without partitions is considered for Rayleigh number (103-106) and Prandtl number (0.7). Vertical walls were maintained isothermal at different temperatures while horizontal walls and the partitions were insulated. The length of partition was taken constant. The number of partitions were placed on horizontal surface in staggered arrangement from (1– 3) and ratio of partition thickness (H/L= 0.033, 0.083, 0.124). The problem is formulated in terms of the vorticity-stream function procedure. A numerical solution based on a program in Fortran 90 with the finite difference method is obtained. Representative results illustrating the effects of the thickn

... Show More
View Publication Preview PDF
Publication Date
Wed Jan 01 2020
Journal Name
Plant Archives
Morpho-physiological study on the effect of lead stress and selenium foliar application on growth of dill plant anethum graveolens l
...Show More Authors

The experiment was carried out in the green house of botanical garden belong to Department of Biology/College of Education for Pure Science Ibn AL-Haitham, University of Baghdad for growing season 2017-2018 to evaluate effect of lead stress with concentrations (0, 50, 100, 150) mg.L -1 and Selenium concentrations (0, 15, 30) mg.L-1 on growth of dill plant using pots. The experiment was designed according to completely randomized design (CRD) with three replications. Result indicated that dill plants subjected to lead stress with height concentrations caused decrease in plant parameters (plant height, no. of branches. plant-1, root length, shoot dry weight, the content of nitrogen, phosphorus and potassium, protein concentration, no. of umbe

... Show More
Scopus (1)
Scopus
Publication Date
Mon Feb 04 2019
Journal Name
Journal Of The College Of Education For Women
Effect of Active Learning Strategy on Mathematical Concepts Acquisition in Mathematics for Fourth Grade Primary
...Show More Authors

Learn new methods of teaching mathematics contribute to raising the level of pupils to acquire mathematical concepts primary stage
Attempt advancement in the level of mathematics teaching for the better through the use of modern teaching strategies. The research aims at the progress in the acquisition of mathematical concepts schoolgirls after subjecting the fourth grade to teach in active learning strategies, the number of research sample (60) schoolgirl, by (30) schoolgirl experimental group and 30 pupils of the control group. Clear from the results shown the presence of a statistically significant difference between the acquisition of concepts of schoolgirls two groups (experimental and control) for the benefit of pupils of the exp

... Show More
View Publication Preview PDF
Publication Date
Sun Sep 05 2010
Journal Name
Baghdad Science Journal
Effect of Hydroxyapatite Coatings on Corrosion Behavior for Biotype 316L SS Used in Orthopaedic Applications
...Show More Authors

Electrochemical corrosion of hydroxyapatite (HAP) coated performance depends on various parameters like applied potential, time, thickness and sintering temperature. Thus, the optimum parameters required for the development of stable HAP coatings was found by using electrophoretic deposition (EPD) technique. This study discusses the results obtained from open circuit potential-time measurements (OCP-time), potentiodynamic polarisation and immersion tests for all alloy samples done under varying experimental conditions, so that the optimum coating parameters can be established. The ageing studies of the coated samples were carried out by immersing them in Ringer’s solution for a period of 30 days indicates the importance of stable HAP c

... Show More
View Publication Preview PDF
Crossref
Publication Date
Sun Mar 01 2015
Journal Name
Baghdad Science Journal
The Effect of Ethanolic Extract for Cyperus rotundus Rhizomes on Liver in Male Albino Mice
...Show More Authors

The present study designed to determine the ethanolic extract of Cyperus rotundus on Liver in Albino Male Mice . In the present study 18 Male mice were used they divided into six groups ( 1st group consedered control group , 2nd group injected by 250 mg/ml from extract , 3th group injected by 300 mg/ml from extract , 4th group injected by 350 mg/ml from extract , 5th group injected by 400 mg/ml from extract and the 6th group injected by 450 mg/ml from extract ) . the expermint lasted for two days and the doses gived by intraperitonial injection . showed from the study results that ethanolic extract for Cyperus rotundus have negative effect on Liver tissue in 250 , 300 , 350 mg/ml concentrations when comparsion with control group . the re

... Show More
View Publication Preview PDF
Crossref
Publication Date
Mon Jun 05 2023
Journal Name
Journal Of Economics And Administrative Sciences
Effect of Public Debt on The Trade Balance in Iraq For The Period (2003-2021)
...Show More Authors

Despite the significant increase in public spending in Iraq, it was not directed toward the important sectors that have an important role in correcting the productive structure. Rather, most of the public expenditure was going to cover the required imports, or to face shocks, whether security or health, and this caused a continuous decrease in the volume of Iraq's exports of goods and services, as the aim of the study was to review the importance of public debt and its impact on the trade balance, as well as to know the economic policies that can contribute to strengthening the trade balance, as the study proved through the (ARDL) model that there is a direct relationship between the domestic debt and the net trade balance, and an invers

... Show More
View Publication Preview PDF
Crossref (2)
Crossref
Publication Date
Thu Feb 29 2024
Journal Name
International Journal Of Design & Nature And Ecodynamics
Artificial Neural Network Assessment of Groundwater Quality for Agricultural Use in Babylon City: An Evaluation of Salinity and Ionic Composition
...Show More Authors

View Publication Preview PDF
Scopus (7)
Crossref (5)
Scopus Crossref
Publication Date
Thu Jun 01 2023
Journal Name
Baghdad Science Journal
Design and study the effect of inner bore diameter on the magnetic and optical properties of the unipolar lens
...Show More Authors

    Many designs have been suggested for unipolar magnetic lenses based on changing the width of the inner bore and fixing the other geometrical parameters of the lens to improve the performance of unipolar magnetic lenses. The investigation of a study of each design included the calculation of its axial magnetic field the magnetization of the lens in addition to the magnetic flux density using the Finite Element Method (FEM) the Magnetic Electron Lenses Operation (MELOP) program version 1 at three different values of current density (6,4,2 A/mm2). As a result, the clearest values and behaviors were obtained at current density (2 A/mm2). it was found that the best magnetizing properties, the high

... Show More
View Publication Preview PDF
Scopus (1)
Scopus Crossref
Publication Date
Sat Oct 01 2022
Journal Name
Digest Journal Of Nanomaterials And Biostructures
Preparation and study effect of vacuum annealing on structure and optical properties of AgCuInSe<inf>2</inf> thin film
...Show More Authors

Scopus (15)
Scopus Clarivate
Publication Date
Mon Mar 11 2019
Journal Name
Al-khwarizmi Engineering Journal
An Investigation Study of Tool Geometry in Single Point Incremental Forming (SPIF) and their effect on Residual Stresses Using ANOVA Model
...Show More Authors

Incremental forming is a flexible sheet metal forming process which is performed by utilizing simple tools to locally deform a sheet of metal along a predefined tool path without using of dies. This work presents the single point incremental forming process for producing pyramid geometry and studies the effect of tool geometry, tool diameter, and spindle speed on the residual stresses. The residual stresses were measured by ORIONRKS 6000 test measuring instrument. This instrument was used with four angles of (0º,15º,30º, and 45º) and the average value of residual stresses was determined, the value of the residual stress in the original blanks was (10.626 MPa). The X-ray diffraction technology was used to measure the residual stresses

... Show More
View Publication Preview PDF
Crossref (1)
Crossref