Several directional wells have been drilled in Majnoon oilfield at wide variation in drilling time due to different drilling parameters applied for each well. This technical paper shows the importance of proper selection of the bit, Mud type, applied weight on Bit (WOB), Revolution per minute (RPM), and flow rate based on the previous wells drilled. Utilizing the data during drilling each section for directional wells that's significantly could improve drilling efficiency presented at a high rate of penetration (ROP). Based on the extensive study of three directional wells of 35 degree inclination (MJ-51, MJ-52, and MJ-54) found that the applied drilling parameters for MJ-54 and the bit type within associated drilling parameters to drill

There are varieties of reasons lead for drilling horizontal wells rather than verticals. Increasing the recovery of oil, especially from thin or tight reservoir permeability is the most important parameter.

East Baghdad oil field considered as a giant field with approximately more than 1billion barrel of a proved reserves accompanying recently to low production rate problems in many of the existing wells.

   It is important to say that presence of of  horizontal wells in East Baghdad field especially by converting some of already drilled wells by re-entry drilling horizontal sections may provide one of best solutions for the primary development stage in East Baghdad field which may be followed by drilling n

After 2003 Iraq witnessed a rapid development in the number and kind of non-governmental organizations in addition to the increase in their sources.A lot of obstacles and constraints hinder the development of the said organizations and one of the most important and prominent obstacles is their administrative and accounting structure that affect directly on the existence, continuity and survival of these organizations.This research discussed the concept the non-governmental organizations and reaching the assessment of internal control System in these organizations. Therefore, the researcher has assessed the internal control System applied National Olympic Committee of Iraq. The study showed vulnerabilities in the internal control the said

Objectives: As health care workers on the front line during the coronavirus (COVID-19) pandemic, dental practitioners are amongst those at risk due to their close contact with potentially infected individuals. The aim of the current study was to assess the anxiety, awareness practice modification, and economic impact amongst Iraqi dentists whilst working during the outbreak.

Methods: This study was performed using an online survey questionnaire with aid of Google forms from 2nd to 23rd July 2020. A total of 484 clinicians responded. The questionnaire was composed of open end, closed end, and Likert five-point scale questions to assess anxiety, awareness and financial impa

The maximization of the net present value of the investment in oil field improvements is greatly aided by the optimization of well location, which plays a significant role in the production of oil. However, using of optimization methods in well placement developments is exceedingly difficult since the well placement optimization scenario involves a large number of choice variables, objective functions, and restrictions. In addition, a wide variety of computational approaches, both traditional and unconventional, have been applied in order to maximize the efficiency of well installation operations. This research demonstrates how optimization approaches used in well placement have progressed since the last time they were examined. Fol

In this work, calculation of pressure losses in circulating system for two drilling muds is evaluated in Noor oil field. Two types of drilling muds that were used for drilling section 12 1/4" and 8 3/4" which are Salt saturated mud and Ferro Chrome Lignosulfonate-Chrome Lignite mud. These calculations are based on field data that were gathered from the drilling site of well Noor-15, which are included, rheological data, flow data and specification of drill string. Based on the obtained results, the best rheological model that fit their data is the Herschel-Bulkley model according to correlation coefficient value for their two drilling mud. Also, the difference between the calculated pressure lo

Hydrodynamics is the interpretation of subsurface fluids and pressures to explain and predict hydrocarbon occurrence and trapping. Different models of fluid flow and hydrocarbon entrapments were constructed for the Mishrif Formation in (Rumaila South RU, Rumaila North R, West Qurna WQ, Majnon MJ, and ZubairZB) oilfields in Basra, southern Iraq. The dynamic flow within the oil reservoir was analyzed by measuring the specific gravity, hydrostatic pressure, hydrodynamic pressure, pressure gradient, salinity and hydraulic head. Fluid saturation in the pore space, hydrodynamic parameters, density, permeability and buoyancy influence fluid flow. The hydrodynamic model indicates that the oil fields are non-isolated reservoirs with a unifor

The current research aims to identify the psychological well-being of the educational counselors, as well as to identify the significance of differences in psychological well-being according to the variables (gender, duration of service). The number of scale's items reached (42) items distributed evenly on six dimensions (autonomy, environmental mastery, personal growth, positive relationships with others, purpose in life, self-acceptance), for each field (7) items. The scale was applied to a sample of (400) school counselors (male-female) who were randomly selected from the six directorates in the Baghdad governorate for the academic year 2020/2021. The results showed that the educational counselors in the Baghdad governorate for the si

This paper attempted to study the effect of cutting parameters (spindle speed and feed rate) on delamination phenomena during the drilling glass-polyester composites. Drilling process was done by CNC machine with 10 mm diameter of high-speed steel (HSS) drill bit. Taguchi technique with L16 orthogonal layout was used to analyze the effective parameters on delamination factor. The optimal experiment was no. 13 with spindle speed 1273 rpm and feed 0.05 mm/rev with minimum delamination factor 1.28.                                       &