Morphologies of ceramic hollow fiber membranes prepared by a combined phase-inversion and sintering method were studied. The organic binder spinning solution containing suspended Al₂O₃ powders was spun to a hollow fiber precursor, which was then sintered at elevated temperatures( 300 ˚C, 1400 ˚C, 25 ˚C) in order to obtain the Al₂O₃ hollow fiber membranes. The spinning solution consisted of polyether sulfone (PES), N-methyl-2-pyrrolidone (NMP), which were used as polymer binder, solvent, respectively. The prepared Al₂O₃ hollow fiber membranes were characterized by a scanning electron microscope (SEM). It is believed that finger-like void formation in asymmetric ceramic membranes is initiated by hydrodynamically unstable viscous fingering developed when a less viscous fluid (non-solvent) is in contact with a higher viscosity fluid (ceramic suspension containing invertible polymer binder). The effects of the air-gap (0 cm, 2 cm, 15 cm) on fibre morphology have been studied and it has been determined that viscosity due to change in air-gap is the dominating factor for ceramic systems.
Explosive power is a crucial factor in athletic performance due to its connection to the skill-based aspects required in every sport. Therefore, understanding it is essential for guiding research and plays a key role in improving shot put performance for short-statured athletes in category (F40). Biomechanical variables also contribute to shot put performance for short-statured athletes in category (F40) by helping coaches identify, diagnose, and compare technical and motor errors, their components, timing, and speed with the required performance to achieve optimal results. Thus, the importance of this research lies in the researchers' attempt to identify the relationship between the explosive power of the upper and lower limbs and certain
... Show MoreAbstract\
preparation process of performance evaluation in organizations is of extreme importance, and under development in organizations and the opening of markets and technological developments in the industry and heightened competition among industrial organizations imposed systems are built for performance give a clear picture about performance and competition, And centered research problem in answering the following questions: Is performance evaluation system is available in Wasit State Company for Textile Industries(Research sample ), This research aims to assess the performance of policies and programs in the company, according to guide performance evaluation of programs and policies prepared by the Dutch Cou
... Show MoreResearch on the role of organizational change in easing the organizational conflict focuses for being one of the important topics and relatively modern and which have a significant impact on the future of organizations, so this study was to identify the relationship and the impact of organizational change and of deportation (technological, organizational structure, human resources, the change in the task) at the organizational conflict in the Earth company link Iraq, in order to reach the goals of the research, it has been the development of a questionnaire distributed to a random sample of (100) composed employees from managers and heads of departments and the people and staff at the Earth company link Iraq, the study found: the
... Show MoreThe purpose of this paper is to identifying the level of skill self-esteem of the young tennis players in the Governorate of Baghdad, identifying some aspects of attention (acuteness, concentration, and diversion of attention) among the young tennis players of the Baghdad governorate, and identify the skills of serve and serve spiking in tennis by young tennis players in Baghdad governorate. The researchers used the descriptive approach in the correlative relations style for its suitability and the research problem. the research sample was chosen in a deliberate way from the youth team players in tennis for the Governorate of Baghdad and the participants in the 2021-2022 sports season, whose number is (20) male players and (4) young playe
... Show MoreStatistics indicate criminal in most countries of the world that the suicide rate continues to increase, as it prevalence manufacturing and complexity of life and the intensification of conflicts and escalating problems of rising suicide rates. And suicide is death intentional, that is, the intentional act that leads to ending the life of the individual and self-on purpose. The current research aims to identify the suicide in terms of its causes and its factors and come up with recommendations for the prevention of suicide. Because suicide is a life-threatening problem has tried several theories of interpretation and stand on its grounds. Considering the theories of psychoanalysis (Freud) that suicide is the result of the individ
... Show MoreThis paper proposes a new method to tune a fractional order PID controller. This method utilizes both the analytic and numeric approach to determine the controller parameters. The control design specifications that must be achieved by the control system are gain crossover frequency, phase margin, and peak magnitude at the resonant frequency, where the latter is a new design specification suggested by this paper. These specifications results in three equations in five unknown variables. Assuming that certain relations exist between two variables and discretizing one of them, a performance index can be evaluated and the optimal controller parameters that minimize this performance index are selected. As a case study, a thir
... Show MoreThe current study included the collection of 175 samples of blood (Urea-blood) of patients with rheumatoid arthritis from Al–Al-Kindy Teaching Hospital, Baghdad Teaching Hospital and Al-Imamian Al-Kadhimyain Medical City in Baghdad from both sexes with different ages at the period between 1/10/2016-1/2/2017. Bacterial growth results showed that 80% of urea for bacterial transplantation were positive results, while the number of samples showing no bacterial growth was 20%. The bacterial isolation evaluate for morphological testes and biochemical microscopy, as well as identification by Api system. The highest frequency of inflectional bacteria was E. coli (41.97%), followed by E. cloacae (21.25%), P. aeruginosa (12.5%), Salmonella (10%), K
... Show MoreThis research was aimed to study the pollen morphology for the genus Pterocephalus(Vaill) from Dipsacaceae family in Iraq, and to utilize these feathers in isolating the species as valuable taxonomic traits for enriching Iraqi flora. The study included characteristics of the type, shape, size, sculpturing and apertures, as well as determining the full dimensions using light microscopy as well as numerical analysis of this species and draw polygonal shapes and denderogram convergence between species. The results of the study of pollen and polygonal forms showed significant differences in the characteristics at the level of each species, which helps to identification the genus species, as it was found that the pollen was a tricolp
... Show MoreGiant Cell Fibroma (GCF) is a relatively rare oral mucosal lesion, so named due to the characteristic giant cells present within the fibrous stroma of the lesion, limited number of clinicopathological studies were performed in previously published literature. This study was performed to evaluate the clinicopathological features of Giant cell fibroma in a sample of Iraqi patients. Formalin-fixed paraffin-embedded sections from 22 giant cell fibroma in period between 2010 and 2018 were retrieved from the laboratory of oral pathology of Baghdad University/College of Dentistry, Clinical data and microscopic features were reviewed and analyzed according to the available surgical reports. The mean age of patients at the time of diagnosis was 29.6
... Show MoreIn this research has been the manufacture and study the properties of the solar cell type retail hybrid manner thermal evaporation emptiness were studying the properties of the cell at room temperature showed measurements stream circuit behavior linear cell manufacturers reached were calculated efficiency tool cell manufacturers, as well as the expense of workers filling the cell