Background: The use of osseointegrated fixtures in dentistry has been demonstrated both histologically and clinically to be beneficial in providing long term oral rehabilitation in completely edentulous individual. Most patients suffer from denture instability; particularly with mandibular prosthesis, the use of dental implant will be benefit significantly from even a slight increase in retention. The concept of implanting two to four fixtures in a bony ridge to retain a complete denture prosthesis appealing therefore, as retention, stability and acceptable economic compromise to the expanse incurred with the multiple fixture supported fixed prosthesis. Materials and methods in this study the sample were eight patients selected from a hosp

In this work, the effect of the addition of bright nickel plating and silver carried out by the electroplating method has been studied, on the coating of copper nanoparticles on the copper base metal via the process of thermal evaporation. The improvement of the solar absorber using CuNP in combination with the bright nickel and silver was obtained to be better than copper nanoparticles individually. A bright nickel enhanced the absorbed thermal stability. Also, other optical properties, absorptions, and emissivity slightly decreased from (93% to 87%), while the existence of silver had a slight impact on absorption of about (86.50%). On the other hand, thermal conductivity was evaluated using hot disk analyzer. The results showed a good

Pyrolysis of high density polyethylene (HDPE) was carried out in a 750 cm3 stainless steel autoclave reactor, with temperature ranging from 470 to 495° C and reaction times up to 90 minute. The influence of the operating conditions on the component yields was studied. It was found that the optimum cracking condition for HDPE that maximized the oil yield to 70 wt. % was 480°C and 20 minutes. The results show that for higher cracking temperature, and longer reaction times there was higher production of gas and coke. Furthermore, higher temperature increases the aromatics and produce lighter oil with lower viscosity.

The phenomenon of the social movements of researchers, based on the scope of their influence on political events, and the nature of the wide role played, and its ability to influence, through its activities and various activities and various. It has practiced its activities through new and non-traditional peaceful means, with clear slogans and specific objectives. And was able to mobilize activists from different strata of the Iraqi people, and its categories and social strata. As the demands focused on freedoms, rights, dignity and social justice

Ball and Plate (B&P) system is a benchmark system in the control engineering field that has been used to verify many control methods. In this paper the design of a sliding mode . controller has been investigated and verified in real-time via implementation on a real ball and plate system hardware. The mathematical model has been derived and the necessary parameters have been measured. The sliding mode controller has been designed based on the obtained mathematical model. The resulting controller has been implemented using the Arduino Mega 2560 and a ball and plate system built completely from scratch. The Arduino has been programmed by the Arduino support target for Simulink. Three test signals has been used for verification purposes

This studies p- CuO / n - Si hete-rojunction was deposited by high vacuum thermal evaporation of Copper subjected to thermal oxidation at 300 oC on silicon. Surface morphology properties of The optical properties concerning the transmission spectra were studies for prepared thin films. this structure have been studied. XRD anaylsis discover that the peak at (𝟏𝟏𝟏-) and (111) plane are take over for the crystal quality of the CuO films. The band gap of CuO films is found to be 1.54 eV. The average grain size of is measured from AFM analysis is around 14.70 nm. The responsivity photodetector after deposited CuO appear increasing in response

The research issue and its importance concentrate on the importance of choosing and
preparing the kindergarten's teacher educationally ,psychologically and artistically ,and other
aspects because of their need for several skills such as the drawing skill for kindergarten
curriculums include a various artistic experiences and activities as well as for the drawing
importance for the child .And from this, the research goals raise from to prepare a test that
measures the drawing skill for kindergarten students and measure the drawing skill in all four
kindergarten students at the kindergarten department and recognize the differences level for
these students . In order to achieve the first goal in the research ,the resear

The research is marked by (Development Design Interior spaces for children's theater halls in the city of Baghdad). Which consists of four chapters, namely, the first chapter the research problem and the need for him, which included identifying the research problem and of poor achievement of aesthetic values and functional at the scene of the child and its significance in that it is a way of cultural entertainment education of the child and its objectives as it aims to evelop interiors for children's theater, and its limits. Theater Magic Lantern in the city of Baghdad, the second chapter addressed the theoretical framework, which consists of the psychology of the child, and space Children's Theatre and types, forms of children's theater