This article uses coupled Eulerian–Lagrangian finite element algorithm to conduct a three-dimensional thermomechanical study to capture the shape and characteristics of defect type generated while achieving the dissimilar friction stir welding of aluminium alloys. The volume-of-fluid method is used to model the Eulerian region and predict the localised formation of process defects. Three different tool shapes are utilised to achieve the dissimilar friction stir welding joining between AA 2024-T3 on the advancing side and AA 6061-T6 on the retreating side. Process parameter effects such as rotational tool speed, traverse tool speed and tool tilt angle are also investigated. The finite element model results are validated by comparing with the results of a previous experimental study. The results showed the augmentation of the traverse welding speed from 40 to 80 mm/min is a key factor in causing process imperfections such as void and tunnel defects. The lower tilt angle value of 1° resulted in long tunnel defects when high rotational speeds are applied. Also, the combination of high rotational and low transverse speeds promotes the production of a free-defect friction stir welding joint.
Objective: To conduct a standardized method for cavity preparation on the palatal surface of rat maxillary molars and to introduce a standardized method for tooth correct alignment within the specimen during the wax embedding procedure to better detect cavity position within the examined slides. Materials and methods: Six male Wistar rats, aged 4-6 weeks, were used. The maxillary molars of three animals were sectioned in the frontal plane to identify the thickness of hard tissue on the palatal surface of the first molar which was (250-300µm). The end-cutting bur (with a cutting head diameter of 0.2mm) was suitable for preparing a dentinal cavity (70-80µm) depth. Cavity preparation was then performed using the same bur on the tooth surf
... Show MoreAn analytical method and a two-dimensional finite element model for treating the problem of laser heating and melting has been applied to aluminum 2519T87and stainless steel 304. The time needed to melt and vaporize and the effects of laser power density on the melt depth for two metals are also obtained. In addition, the depth profile and time evolution of the temperature before melting and after melting are given, in which a discontinuity in the temperature gradient is obviously observed due to the latent heat of fusion and the increment in thermal conductivity in solid phase. The analytical results that induced by laser irradiation is in good agreement with numerical results.
Objective: To conduct a standardized method for cavity preparation on the palatal surface of rat maxillary molars and to introduce a standardized method for tooth correct alignment within the specimen during the wax embedding procedure to better detect cavity position within the examined slides. Materials and methods: Six male Wistar rats, aged 4-6 weeks, were used. The maxillary molars of three animals were sectioned in the frontal plane to identify the thickness of hard tissue on the palatal surface of the first molar which was (250-300µm). The end-cutting bur (with a cutting head diameter of 0.2mm) was suitable for preparing a dentinal cavity (70-80µm) depth. Cavity preparation was then performed using the same bur on the tooth
... Show MoreThis study proposes a new version of the Autoregressive Integrated Moving Average (ARIMA) model using Artificial Neural Networks (ANNs) denoted by ARIMA-NN. The new model incorporates a multi-layer perceptron with matrix multiplication within a feed-forward network. The logistic, hyperbolic tangent (tanh), and sigmoid activation functions are used for weight updates in ARIMA-NN. A new forecasting algorithm is proposed, and one-step and multiple-steps forecasting procedures are rigorously analyzed. The proposed model was evaluated against existing forecasting model using performance metrics such as the Akaike Information Criterion (AIC) and Bayesian Information Criterion (
... Show MoreThis study aims to numerically simulate the flow of the salt wedge by using computational fluid dynamics, CFD. The accuracy of the numerical simulation model was assessed against published laboratory data. Twelve CFD model runs were conducted under the same laboratory conditions. The results showed that the propagation of the salt wedge is inversely proportional to the applied freshwater discharge and the bed slope of the flume. The maximum propagation is obtained at the lowest discharge value and the minimum slope of the flume. The comparison between the published laboratory results and numerical simulation shows a good agreement. The range of the relative error varies between 0 and 16% with an average of 2% and a roo
... Show MoreFinding communities of connected individuals in complex networks is challenging, yet crucial for understanding different real-world societies and their interactions. Recently attention has turned to discover the dynamics of such communities. However, detecting accurate community structures that evolve over time adds additional challenges. Almost all the state-of-the-art algorithms are designed based on seemingly the same principle while treating the problem as a coupled optimization model to simultaneously identify community structures and their evolution over time. Unlike all these studies, the current work aims to individually consider this three measures, i.e. intra-community score, inter-community score, and evolution of community over
... Show MoreThe aim of this study is to recognize the influence of model of active thinking in achievement ofeighth grade students andtheir visual thinking in science.The finds of this research show the superiority students of the experimental group who studied the science material by using the active thinking model on the students of the control group who studied by usual method, in the achievement test. Also the finds show that the students of the experimental group are more successful than students of control group in the test of visual thinking, so the two null hypotheses have been rejected. In light of the results of the research, numbers of recommendations were made.
Abstract
Oil is considered a commodity and is still an important and prominent role in drawing and shaping the Iraqi economic scene. The revenues generated from the export of oil are considered the main source of the general budget in cash flows.
Since the revenues consist of quantity and price and the latter is an external factor which is difficult to predict, The effect of any commodity on its price, which is proven in the theory of micro-economic, but it is observed through the research that the response is slow, which means not to take advantage of the rise in prices, by increasing the quantity exported, the result of several facto
... Show MoreVolleyball is one of the sports that require physical and skill abilities thus many teaching models appeared to teach these abilities like group investigation model. The research aimed at identifying the effect of group investigation model on learning underarm and overhead passing in volleyball. The researchers hypothesized statistical differences between pre and posttests in learning underarm and overhead passing in volleyball as well as differences in posttests of controlling and experimental groups in learning underarm and overhead passing in volleyball. The researcher used the experimental method on (30) second year female students of physical education and sport sciences college/ university of Baghdad. Group investigation model was app
... Show MorePOSSIBILITY OF APPLICATION THE BALANCED SCORECARD IN THE IRAQI INDUSTRIAL COMPANIES: A PROPOSED MODEL