Abstract The study aims to clarify the value of auditing economic units and how it can be measured, which is one of the most important challenges to matching the Value Relevance of Accounting Information. The problem of the study was identified with questions that revolve around the extent to which it is possible to measure the value of auditing in Iraqi economic units and the extent to which the value of auditing affects the adequacy of accounting information. Through reviewing the studies discussing this topic, it was found that auditing can provide value through the performance of the auditor and adding value to the economic unit subject to audit. The study recommended the need to study the situational factors of auditing, whether external or internal, that affect the value of the audit, which would generate the highest value for the consumer of this service through the situational leadership methods of auditing that affect the value obtained by the economic unit subject to auditing, which is called the value of auditing and it is one of the modern topics in the field of audit research. In addition, the results reached will contribute to explaining the value of the audit, that is, the benefit obtained by the economic unit subject to audit and its ability to influence the Value Relevance of Accounting Information and the possibility of enhancing it in the local environment.
A new pavement technology has been developed in Highway engineering: asphalt pavement production is less susceptible to oxidation and the consequent damages. The warm mix asphalt (WMA) is produced at a temperature of about (10-40) oC lower than the hot asphalt paving. This is done using one of the methods of producing a WMA. Although WMA's performance is rather good, according to previous studies, as it is less susceptible to oxidation, it is possible to modify some of its properties using different materials, including polymers. Waste tires of vehicles are one of the types of polymers because of their flexible properties. The production of HMA, WMA, and WMA modified with proportions of (1, 1.5, and 2%) of rub
... Show MoreThe effect of air injection angle on the performance of airlift pump used for water pumping has been studied analytically and experimentally. An airlift pump of dimensions 42mm diameter and 2200 mm length with conventional and modified air injection device was considered. A modification on conventional injection device (normal air-jacket type) was carried out by changing injection angle from 90 (for conventional) to 45 and 22.5 (for modified). Continuity and one-dimensional momentum balance for the flow field with basic principle of two-phase flow and expressions of slip ratio and friction factor as function of flow rates were formulated. The analytical and experimental investigations were carried out f
... Show MoreThe research aims to determine optimal urban planning and design indicators of the urban clusters form in hot arid zones through studying of three urban areas in Baghdad, analyzing their urban indicators which include floor area ratio (FAR), urban clusters height, building density or land coverage, green areas, paved areas, shading ratio and how they affect urban temperature. The research reached the conclusion that air outdoor temperature on urban areas affected primarily by shadows casted on the ground, the effect of shaded area equals (5) times the effect of paved areas and (3.7) times the effect of green areas, this means that increasing urban clusters height in hot arid zones could minimize air outdoor temperature, building
... Show MoreABSTRACT:In this paper, Cd10–xZnxS (x = 0.1, 0.3, 0.5) films were deposited by using chemical spray pyrolysis technique, the molar concentration precursor solution was 0.15 M/L. Depositions were done at 350°C on cleaned glass substrates. X-ray dif- fraction technique (XRD) studies for all the prepared film; all the films are crystalline with hexagonal structure .The optical properties of the prepared films were studied using measurements from VIS-UV-IR spectrophotometer at wave- length with the range 300 - 900 nm; the average transmission of the minimum doping ratio (Zn at 0.1%) was about 55% in the VIS region, it was decrease at the increasing of Zn concentration in the CdS films, The band gap of the doped CdS films was varied as 3.7, 3
... Show MoreAbstract:
The underlying objective of the international standard No. (6) to assist in accounting applications for the extractive industries, taking into consideration the goals and objectives contained in the sixteenth of the private International Accounting Standards criterion accounting for land, machinery and equipment, as well as Standard No. axes (38) relating to intangible assets, and in order to create a vision of a comprehensive development needs oil in order to exact evaluation of policies related to the particular needs and draw a comprehensive frameworks with respect to treatment of expenditures and revenues in the oil production industry, is also interested in Standard No. (6) within the primary objectiv
... Show MoreMagnetic Abrasive Finishing (MAF) is an advanced finishing method, which improves the quality of surfaces and performance of the products. The finishing technology for flat surfaces by MAF method is very economical in manufacturing fields an electromagnetic inductor was designed and manufactured for flat surface finishing formed in vertical milling machine. Magnetic abrasive powder was also produced under controlled condition. There are various parameters, such as the coil current, working gap, the volume of powder portion and feed rate, that are known to have a large impact on surface quality. This paper describes how Taguchi design of experiments is applied to find out important parameters influencing the surface quality generated during
... Show MoreThe study showed a significant rise in the proportion of the labor force in agriculture
activity among the detailed economic activities in 1997 with a rate (%28.9), and then
decreased to (%18.8) in 2011, and this belong to the deterioration of agriculture and the
transition to the other economic activities.
2- The highest percentage of male's participation in year 1997 obtained by the activity (A),
which is represented by agriculture , where was (%30.0) while the highest percentage of
female's participation has been brought by the activity (M) which is represented education
with a rate (% 47.9). while in 2011 that the highest proportion of males' concentration
obtained by the activity (L) with a rate (%23.1) while