This study estimated seven heavy metals (Fe, Cu, Zn, Pb, Ni, Cd, Cr) in water (dissolved and particulate phase), sediments and some aquatic organisms including two species from aquatic plants (Ceratophyllum demersum&Phragmites australis); one species of clam (Psedontopeses euphratics) and two species from fish (Oreochromis aureus& Leuciscus vorax)in four sites within Mashroo AL- Musayyib channel project/ branch of Euphrates river, Babylon , medial of Iraq . This aims to show the concentration of these elements, their fate and the mechanisms of their transmission through the food chain in this lotic aquatic system ; also in addition to examining some physicochemical properties of river water such as water temperature (WT),air temperature (AT),pH , electrical conductivity ( EC) , salinity ,total dissolved solid ( TDS), total solid suspended (TSS) , dissolved oxygen (DO) and biological oxygen demand ( BOD5) .The occurrence in heavy metals in water was found in the order in the Dissolved phase :- Zn> Fe > Cu> Ni>Pb> Cr > Cd, the zinc element recorded the highest rate in site two for spring season while the cadmium element recorded the lowest rate in site one for spring season. In the particulate phase:- Zn> Cu >Fe > Ni>Pb> Cr > Cd, the zinc element recorded the highest rate in site two for spring season while the cadmium element recorded the lowest rate in site four for spring season. The sediment order was Zn> Cu >Fe >Pb> Ni > Cd > Cr where the zinc element recorded the highest rate in site two for spring season where as the chromium element recorded the lowest rate in site two for spring. In aquatic plant the order was in C. demersum :Zn> Fe > Cu>Pb> Cr > Ni > Cd, the zinc element recorded the highest rate in site four for winter season while the cadmium element recorded the lowest rate in site one for autumn season. In P. australis: Zn> Fe > Cu>Pb> Cd > Ni > Cr , the zinc element recorded the highest rate in site two for spring season while the chromium element recorded the lowest rate in site two for spring season. In clam the order was: Zn> Fe > Cu> Ni >Pb> Cd > Cr where the zinc element recorded the highest rate in site two for spring season while the chromium recorded the lowest value in site 3 through winter 2021.In fish species (O. aureas) the order was Fe > Zn > Cu>Pb> Cr > Cd > Ni. The iron element recorded as the highest rate in site 2 in spring 2021 whilethe element that recorded the lowest rate was Ni in site 2for spring in L. vorax. The iron element recorded the highest rate in site one for summer season where as the Nickel was recorded a lower value in site four in spring2021.
Abstract: Iatrogenic furcal root perforations are serious complications during dental treatment. This study was aimed to compare the sealing ability of new bioceramic root repair material TotalFill® with the other perforation repair materials (GIC, MTA and Biodentine) using a dye- extraction method.Materials and Methods: Forty extracted, human mandibular molars with non-fused well developed root were collected. Artificial perforations were made from the external surface of the teeth. Then the teeth were randomly divided into 4 experimental groups (n= 10) according to the type of repair material used in this study; Medifil glass ionomercement, TotalFill® bioceramic root repair material, BiodentineTM and MTA Plus. The specimens were then im
... Show MoreThis work presents a novel technique for the detection of oil aging in electrical transformers using a single mode optical fiber sensor based on surface plasmon resonance (SPR). The aging of insulating oil is a critical issue in the maintenance and performance of electrical transformers, as it can lead to reduce insulation properties, increase risk of electrical breakdown, and decrease operational lifespan. Many parameters are calculated in this study in order to examine the efficiency of this sensor like sensitivity (S), signal to noise ratio (SNR), resolution (refractive index unit) and figure of merit (FOM) and the values are for figure of merit is 11.05, the signal to noise ratio is 20.3, the sensitivity is 6.63, and the resolution is 3
... Show MoreAsthma is one of the most common chronic, non-communicable diseases affecting children worldwide. The estimated prevalence of pediatric asthma in Iraq is 15.8%. Physiologic, inflammatory and structural factors contribute to the development of asthma. Assessment and monitoring of asthma control can be done by a validated children asthma control test (CACT). Management of asthma must address three components which are an appropriate management plan, the most appropriate medication if necessary, and the use of safe and effective medication. The management plan should consider patient counseling and education about the definition of asthma, signs, and symptoms, the pathophysiology of asthma, common triggers for asthma and how can avoid them,
... Show MoreThe effects of nutrients and physical conditions on phytase production were investigated with a recently isolated strain of Aspergillus tubingensis SKA under solid state fermentation on wheat bran. The nutrient factors investigated included carbon source, nitrogen source, phosphate source and concentration, metal ions (salts) and the physical parameters investigated included inoculum size, pH, temperature and fermentation duration. Our investigations revealed that optimal productivity of phytase was achieved using wheat bran supplemented with: 1.5% glucose. 0.5% (NH4)2SO4, 0.1% sodium phytate. Additionally, optimal physical conditions were 1 × 105 spore/g substrate, initial pH of 5.0, temperature of fermentation 30˚C and fermentation dura
... Show MoreActivated carbon prepared from date stones by chemical activation with ferric chloride (FAC) was used an adsorbent to remove phenolic compounds such as phenol (Ph) and p-nitro phenol (PNPh) from aqueous solutions. The influence of process variables represented by solution pH value (2-12), adsorbent to adsorbate weight ratio (0.2-1.8), and contact time (30-150 min) on removal percentage and adsorbed amount of Ph and PNPh onto FAC was studied. For PNPh adsorption,( 97.43 %) maximum removal percentage and (48.71 mg/g) adsorbed amount was achieved at (5) solution pH,( 1) adsorbent to adsorbate weight ratio, and (90 min) contact time. While for Ph adsorption, at (4) solution pH, (1.4) absorbent to adsorbate weight ratio, and (120 min) contact
... Show More