Land use change, particularly the expansion of urban areas and associated human activities at the expense of natural and semi-natural areas, is a major ecological issue in urban areas around the world. Climate change being a very strong additional driver for changing the temperature and habitat in the cities. This also applies to Baghdad, Iraq, where urbanisation and climate change exerts a major pressure on the natural habitats of the city, and thus may affect the ability of city planners to adapt to future climate change scenarios. Here we present evidence of substantial growth in urban areas, increases in temperature, and degradation of natural vegetation within Baghdad city by using Remote Sensing techniques and an assessment for the Jadriyah and Umm Al-Khanazeer site (JUKI). These changes were associated with loss of bird species richness within the area, which was previously the only Important Bird Area (IBA) within the city. A standardised scoring system (following Birdlife International global framework) was used to assess Pressure-State-Response: JUKI site scored 3-5 for pressure (Medium), two for the state (Moderate), and two for the response (Low). Despite the degradation highlighted in Baghdad city, the JUKI site still has 88% intact habitat to support bird trigger species. We conclude that the site urgently needs a detailed management plan to ensure the protection of its habitats and avian fauna, and that the area should be declared as a protected area according to the “IUCN Category IV: Habitat/Species Management Area; to provide a means by which the urban residents may obtain regular contact with nature”, and re-designated JUKI as an IBA site. The study also identifies the most affected areas in the city of Baghdad, which should take the priority of the afforestation efforts and any future restoration campaigns.
MR Younus…, 2020 - Cited by 2
The placement of buildings and structures on/or adjacent to slopes is possible, but this poses a danger to the structure due to failures that occur in slopes. Therefore, a solution or improvement should be determined for these issues of the collapse of the structure as a result of the failure of the slopes. A laboratory model has been built to test the impact of some variables on the bearing capacity factor. The variables include the magnitude of static axial load applied at the center of footing, the depth of embedment, the spacing between geogrid reinforcement layer and the numbering of the geogrid sheet under the footing, the inclination angle of slope clayey soil (β), the spacing between the footing's edge and the slope's end (b/H). Th
... Show MoreDigital Elevation Model (DEM) is one of the developed techniques for relief representation. The definition of a DEM construction is the modeling technique of earth surface from existing data. DEM plays a role as one of the fundamental information requirement that has been generally utilized in GIS data structures. The main aim of this research is to present a methodology for assessing DEMs generation methods. The DEMs data will be extracted from open source data e.g. Google Earth. The tested data will be compared with data produced from formal institutions such as General Directorate of Surveying. The study area has been chosen in south of Iraq (Al-Gharraf / Dhi Qar governorate. The methods of DEMs creation are kri
... Show MoreEssential oils were extracted from Syzqiumoramac clove, Nigella sativa and eucalyptus oil for purpose of studying effect of these oils on adult cockroaches as repellents and extent of their attraction to them by treating biscuits with three concentrations (0.5, 0.25,1%). The results showed that clove oil was significantly more repellent than black seed oil at a concentration (1%), as average for five days was (0.32) compared to black seed oil (1.36). Insects attracted towards lunch averaged 7.58, 14 and this indicates fading of repellent effect due to penetration of the aroma of volatile clove oil. Results also showed that clove oil has a more lethal effect by direct spraying on nymphs and adults than black seed oil, as mortality in
... Show MoreThis paper presents on the design of L-Band Multiwavelength laser for Hybrid Time Division Multiplexing/ Wavelength Division Multiplexing (TDM/WDM) Passive Optical Network (PON) application. In this design, an L-band Mulltiwavelength Laser is designed as the downstream signals for TDM/WDM PON. The downstream signals ranging from 1569.865 nm to 1581.973 nm with 100GHz spacing. The multiwavelength laser is designed using OptiSystem software and it is integrated into a TDM/WDM PON that is also designed using OptiSystem simulation software. By adapting multiwavelength fiber laser into a TDM/WDM network, a simple and low-cost downstream signal is proposed. From the simulation design, it is found that the proposed design is suitable to be used
... Show MoreThe apoptotic activity of methionine γ- lyase from Pseudomonas putida on cancer cell lines was indicated by measuring the concentration of cytochrome c in the supernatants of cell lines. The result revealed high concentration of cytochrome c in the supernatants of cancer cell lines (RD, AMGM and AMN3) respectively while the concentration of anti-apoptotic protein (Bcl-2) was very low.
his analysis aims to establish Riemann-Liouville derivation andintegral operators regarding the recently suggested seven-parameter Mittag-Leffler function then investigates the corresponding special cases. In addition,certain notable results associated with those new operators have been dis-cussed
This research aims to improve the radiation shielding properties of polymer-based materials by mixing PVC with locally available building materials. Specifically, two key parameters of fast neutron attenuation (removal cross-section and half-value layer) were studied for composite materials comprising PVC reinforced with common building materials (cement, sand, gypsum and marble) in different proportions (10%, 30% and 50% by weight). To assess their effectiveness as protection against fast neutrons, the macroscopic neutron cross-section was calculated for each composite. Results show that neutron cross-section values are significantly affected by the reinforcement ratios, and that the composite material PVC + 50% gypsum is an effect
... Show MoreSolar photovoltaic (PV) system has emerged as one of the most promising technology to generate clean energy. In this work, the performance of monocrystalline silicon photovoltaic module is studied through observing the effect of necessary parameters: solar irradiation and ambient temperature. The single diode model with series resistors is selected to find the characterization of current-voltage (I-V) and power-voltage (P-V) curves by determining the values of five parameters ( ). This model shows a high accuracy in modeling the solar PV module under various weather conditions. The modeling is simulated via using MATLAB/Simulink software. The performance of the selected solar PV module is tested experimentally for differ
... Show More