A new novel series of metalcomplexes are prepared from reactions between 2-benzoylthio- benzimidazole (L) with metal salts of Co (II) , Fe(III) and Rh (III) , while Pd(II) complex was obtained by mixing ligandsof 2-benzoylthiobenzimidazole (L) as primary ligand and bipyridine (L/)as secondary ligand as well as palladium chloride as metal salt in an ethanoic medium. The geometry of these compounds were identified using C.H.N.microanalysis, Ultraviolet–visible, Fourier transforms infrared, magnetic susceptibility, molar conductivity and flame atomic absorption (A.A). From the dataobtained by these spectral analyses, the molecular structures for Rh and Fe complexes were proposed to be octahedral geometry. A square planar construction is proposed for Pd(II), while a Tetrahedral Geometry for Cobalt (II)complex. All of the complexes which were prepared displayedobviousconstancy and could be stored for months without showing any considerablealteration. Semi-empirical methods (ZINDO/1, ZINDO/S & PM3) were conducted to assess the heat of formation ∆H˚f, binding energy ∆Eb, and dipole moment for all compounds as theoretic study. The complexes expressnotable biological activities to pathogenic bacteria when inspected on certain bacteria. The synthesized compounds exhibited moderate toverygood antibacterial activity against bacterial strains, i.e., Escherichiacoli, Staphylococcus aureus & Pseudomonas aeruginosa.
In this work, laboratory experiments were carried out to verify direct contact membrane distillation system’s performance in highly saline water desalination. The study included the investigation of various operating conditions, like feed flow rate, temperature and concentration of NaCl solution and their impact on the permeation flux were discussed. 16 cm2 of a flat sheet membrane module with commercial poly-tetra-fluoroethylene (PTFE) membrane, which has 0.22 μm pore size, 96 µm thickness and 78% average porosity, was used. A high salt rejection factor was obtained greater than 99.9%, and the permeation flux up to 17.27 kg/m2.h was achieved at 65°C for hot feed side and 20°C for cold side stream.
This study includes a detailed morphological description of Cosmina baghdadensis sp. nov.
from Iraq.
Many characters are used in identification especially chaetotaxy and male genetalia.
Locality, host plant, and data of collection were given.
The mass attenuation coefficient for beta particles through pure Polyvinyl chloride (PVC) and flax fibers- reinforced PVC composite were investigated as a function of the absorber thickness and the absorber to source distance. The beta particles mass attenuation coefficients were obtained using a NaI(Tl) energy selective scintillation counter with 90Sr/ 90Y beta source having an energy range from (0.546-2.275) MeV. Pure PVC polymer samples were prepared by compacting the PVC powder in a mould at high pressure (10bar) and temperature about 140°C for 30 minutes. A hot press system was used for this process. The experimentally obtained values of mass attenuation coefficients for 90Sr and 90Y were found to be 7.72 cm2.g-1and 0.842 cm2.g-1 r
... Show MoreThe research aims to determine the role of the training strategy with its dimensions of (strategic analysis, formulation of training strategy, implementation of training strategy, evaluation) in the pioneering performance of the organization with its dimensions of (pre-planning , renewal and modernization, efficiency, effectiveness). Important and modern in pioneering performance and training strategy, and in recognition of the importance of the subject and the expected results of the surveyed banks, an analysis was made of the data obtained through field visits in addition to the questionnaire and interviews ,and the most prominent results that were reached were taking the research sample into consideration all the requirements of the trai
... Show MoreThis investigation aimed to explain the mechanism of MFCA by applying this method on air-cooled engine factory which was suffering from high production cost. The results of this study revealed that MFCA is a useful tool to identify losses and inefficiencies of the production process. It is found that the factory is suffering from high losses due to material energy and system losses. In conclusion, it is calculated that system losses are the highest among all the losses due to inefficient use of available production capacity.
Water pollution is an issue that can be exacerbated by drought as increased concentrations of unwanted substances are a consequence of lower water levels. Polluted water that flows into natural marshlands leads to the deposition of pollutants in the interior of the marsh. Here we present evidence that the interior of the Central Marsh (CM) in southern Iraq suffers from higher levels of pollution than areas closer to the source of water entering the marsh (the Euphrates River). A 1.7m embankment that halts the flow of the Euphrates is only infrequently breached and so the CM is effectively the terminal destination of the waters (and their associated pollutants and agricultural waste) flowing from the West of Iraq.
A range of water
... Show MoreThere are numerous ways to define the traits of influential professors, including behavior (such as warmth, civility, and clarity), knowledge (of subject matter and students), and beliefs, among many others. According to research; influential teaching can also defined as the capacity to improve student achievement. This; is only one way to express effectiveness, as stated. However; the preferred definition of high-quality teaching in the United States and many other countries is teacher effects on student achievement. Therefore; this study aimed to determine the characteristics of influential professors in Online Teaching at the English department. This study; believed to be significant for college professors who will show them how
... Show MoreBackground. Material tribology has widely expanded in scope and depth and is extended from the mechanical field to the biomedical field. The present study aimed to characterize the nanocoating of highly pure (99.9%) niobium (Nb), tantalum (Ta), and vanadium (V) deposited on 316L stainless steel (SS) substrates which considered the most widely used alloys in the manufacturing of SS orthodontic components. To date, the coating of SS orthodontic archwires with Nb, Ta, and V using a plasma sputtering method has never been reported. Nanodeposition was performed using a DC plasma sputtering system with three different sputtering times (1, 2, and 3 hours). Results. Structural and elemental analyses were conducted on the deposited coating
... Show More