Abstract:

There is a close relationship between rigidity and distort structure of production and productivity and inflation rates. The effects of this relationship are distorted the contribution rate of the productive sectors and the disproportionate of exchange rate in foreign trade.

raising the general level of prices is one of the way that have been used by previous governments (inflationary financing or deficit financing) in order to speed up the process of capital formation, depending on the availability of economic resources idle.

The fabricating inflation for development does not represent a true understanding of the nature of the

In this paper, a discussion of the principles of stereoscopy is presented, and the phases
of 3D image production of which is based on the Waterfall model. Also, the results are based
on one of the 3D technology which is Anaglyph and it's known to be of two colors (red and
cyan).
A 3D anaglyph image and visualization technologies will appear as a threedimensional
by using a classes (red/cyan) as considered part of other technologies used and
implemented for production of 3D videos (movies). And by using model to produce a
software to process anaglyph video, comes very important; for that, our proposed work is
implemented an anaglyph in Waterfall model to produced a 3D image which extracted from a
video.

Experimental investigations had been done in this research to demonstrate the effect of carbon fiber and Ceramic fillers contents on the tribological behaviour of (15% volume fraction) carbon-epoxy composite system under varying volume fraction, load, time and sliding distance. The wear resistance were investigated according to ASTM G99-05standard using pin on disc machine to present the composite tribological behaviour. The influence of three ceramic fillers, granite, perlite and calcium carbonate (CaCO₃), on the wear of the carbon fabric reinforced epoxy composites under dry sliding conditions has been investigated. The effect of variants in volume fraction, applied load, time and sliding distance on the wear behaviour of po

الكوارث الطبيعية واضرارها على حياة الانسان قديمة لاتحددها فترة زمنية بعينها دون الاخرى ،  انها موجودة مند الازل قدم لنا القران الكريم ، والحديث النبوي الشريف ، وكتب التاريخ والجغرافية والبلدان ، وكتب الثقافة العامة وكتب الانواء ، وبعض الكتب المستقلة في الموضوع ومنها كتاب كشف الصلصة في وصف الزلزلة للسيوطي ( ت 911هـ) نمادج لا تحصى من انواع الكوارث الطبيعية ، والتبدلات الجذرية التي حلت بالمجتمعات نتيجة لوقوع

It is from the greatness of God Almighty and from him that he facilitated for me to delve into the immersion of the hadith of the Prophet in my doctoral dissertation, then I found it a fertile ground for the cultivation of scientific results.
Through this work, I chose the topic (Replies of Al-Aini to Ibn Malik in his book Umdat Al-Qari Sharh Sahih Al-Bukhari) because of its scientific impact, as such topics inspire in the soul of the follower and the student a lot of contemplation and great care to understand the texts and then come up with a result that is almost close. It is correct, and my current situation in this research is the condition of many scholars, not without errors and omissions. Whatever was correct is by the grace of

The research aims to design an electronic program that allows users to assess the possibility of different practices for projects management professional according to the PMBOK methodology)) and using the requirements Data mentioned in the "knowledge and experience in project management Evaluation guide" issued by the professional Institute of project management According to the results of this program will be electronic The possible classification of project management in terms of both (proficiency_ perform tasks) as less than the desired level or within or above average in terms of best practices, and finally a number of recommendations to overcome the possible shortcomings. The most important is the need to enrich the service

Milling Machining is a widely accepted nontraditional machining technique used to produce parts with complex shapes and configurations. The material is removed in two stages roughing and finishing, the flat end cutter removed the unwanted part of material, then finished by end mill cutter. In milling technique, the role of machining factors such as cutting depth, spindle speed and feed has been studied using Taguchi technique to find its effectiveness on surface roughness.  Practical procedure is done by Taguchi Standard matrix. CNC milling is the most conventional process which is used for removing of material from workpiece to perform the needed shapes. The results and relations indicate that the rate of feed is v

Experiments were conducted to study axial liquid dispersion coefficient in slurry bubble column of 0.15 m inside diameter and 1.6 m height using perforated plate gas distributor of 54 holes of a size equal to 1 mm diameter and with a 0.24 free area of holes to the cross sectional area of the column. The three phase system consists of air, water and PVC used as the solid phase. The effect of solid loading (0, 30 and 60 kg/m³) and solid diameter (0.7, 1.5 and 3 mm) on the axial liquid dispersion coefficient at different axial location (25, 50 and 75 cm) and superficial gas velocity covered homogeneous-heterogeneous flow regime (1-10 cm/s) were studied in the present work. The results show that the axial liquid dispersion coeffic

Footnotes are considered as an important phenomenon in the lectures of grammar. Al-Khudari's footnote is one of the most distinguished one other than its counterparts due to the prestigious and scientific status of its author