The olive tree, has been used it is important plant for the time being some of their parts on a large scale in the treatment of gastrointestinal disorders and stimulate circulation . Moreover, it is used as antibacterial material and also to address some of the respiratory system, diabetes, food preservation osteoporosis. This study involved the collection of olive leaves from different areas in Baghdad / Iraq. These leaves have been harvested, wash it, then dried and crushed, where the study aimed to identify the active ingredients and chemical elements in the olive leaf as well as its effect on the action of GOT enzyme .The study showed that the aqueous extracts (cold and hot) of the olive leaves powder are acidic in nature pH values are of (5.74 and 5.40) for the aqueous extracts hot and cold respectively. Study revealed the extract contain the a collection of Glycosides, tannins, phenolic compounds, resins, flavonoids, alkaloids, terpenes and compound Alaolurobin. The study also showed ability to activate the enzyme GOT in cold aqueous extract (8.36%). and the percentage (27.35%) of hot aqueous extract. That can be analyzed to the presence of higher concentrations of the active compounds in hot aqueous extract compared with cold aqueous extract especially tannins working to activate enzymes carrier in the cell membrane in the body. The study showed that the analysis of thin layer chromatography, liquid high-performance, ( TLC, HPLC) in extract compounds of phenols olive leaf using a mixture (chloroform, acetic acid) and a 2:5 was more impact in the Gram-positive Staphylococcus aureus, while less impact in a negative Gram Salmonella typhimurium. As proved accurate analysis of the chemical elements in powder of plant leaf olive tree and at different concentrations contain of chemical elements Major estimated by (g /kg) and trace estimated by (mg/kg). Since the existence of these elements led to increasing of enzymatic effectiveness through an increase process of activity the enzyme (GOT), which plays role of important in our bodies being gives indication of the nature of the work and effectiveness of the activity of some members of the body (liver, kidney, pancreas, etc.).
This research is carried out to investigate the behavior of self-compacting concrete (SCC) two-way slabs with central square opening under uniformly distributed loads. The experimental part of this research is based on casting and testing six SCC simply supported square slabs having the same dimentions and reinforcement. One of these slabs was cast without opening as a control slab. While, the other five slabs having opening ratios (OR) of 2.78%, 6.25%, 11.11%, 17.36% and 25.00%. From the experimental results it is found that the maximum percentage decrease in cracking and ultimate uniform loads were 31.82% and 12.17% compared to control slab for opening ratios (OR
... Show MoreAbstract: Aluminum alloys grade 6061-T6 are characterized by their excellent properties and processing characteristics which make them ideal for varieties of industrial applications under cyclic loading, aluminum alloys show less fatigue life than steel alloys of similar strength. In the current study, a nanosecond fiber laser of maximum pulse energy up to 9.9 mJ was used to apply laser shock peening process (LSP) on aluminum thin sheets to introduce residual stresses in order to enhance fatigue life under cyclic loading Box-Behnken design (BBD) based on the design of experiments (DOE) was employed in this study for experimental design data analysis, model building and optimization The effect of working parameters spot size (ω), scannin
... Show MoreThis paper aims to study the effect of circular Y-shaped fin arrangement to improve the low thermal response rates of a double-tube heat exchanger containing Paraffin phase change material (PCM). ANSYS software is employed to perform the computational fluid dynamic (CFD) simulations of the heat exchanger, including fluid flow, heat transfer, and the phase change process. The optimum state of the fin configuration is derived through sensitivity analysis by evaluating the geometrical parameters of the Y-shaped fin. For the same height of the fins (10 mm), the solidification time is reduced by almost 22%, and the discharging rate is enhanced by almost 26% using Y-shaped fins compared with the straight fins. The results demonstrate that the sol
... Show MoreAbstract
Objective(s): To determine the interventional program effectiveness on nurses' practices concerning diet instructions for orthopedic patients treated by internal fixation devices.
Methodology: A quantitative approach using prexperimental design is conducted to determine the effectiveness of an interventional program on nurses’ practices regarding orthopedic patients diet instruction and teaching after internal fixation implemented. The study has started from 1st of April 2022 and ended on 15th of December, 2022. The conduction of the study in Misan governorate / Al-Zaharawy surgical hospital. A non-probability, purpo
... Show MoreIn the geotechnical and terramechanical engineering applications, precise understandings are yet to be established on the off-road structures interacting with complex soil profiles. Several theoretical and experimental approaches have been used to measure the ultimate bearing capacity of the layered soil, but with a significant level of differences depending on the failure mechanisms assumed. Furthermore, local displacement fields in layered soils are not yet studied well. Here, the bearing capacity of a dense sand layer overlying loose sand beneath a rigid beam is studied under the plain-strain condition. The study employs using digital particle image velocimetry (DPIV) and finite element method (FEM) simulations. In the FEM, an experiment
... Show MoreThe paper present design of a control structure that enables integration of a Kinematic neural controller for trajectory tracking of a nonholonomic differential two wheeled mobile robot, then proposes a Kinematic neural controller to direct a National Instrument mobile robot (NI Mobile Robot). The controller is to make the actual velocity of the wheeled mobile robot close the required velocity by guarantees that the trajectory tracking mean squire error converges at minimum tracking error. The proposed tracking control system consists of two layers; The first layer is a multi-layer perceptron neural network system that controls the mobile robot to track the required path , The second layer is an optimization layer ,which is impleme
... Show MoreSolid‐waste management, particularly of aluminum (Al), is a challenge that is being confronted around the world. Therefore, it is valuable to explore methods that can minimize the exploitation of natural assets, such as recycling. In this study, using hazardous Al waste as the main electrodes in the electrocoagulation (EC) process for dye removal from wastewater was discussed. The EC process is considered to be one of the most efficient, promising, and cost‐effective ways of handling various toxic effluents. The effect of current density (10, 20, and 30 mA/cm2), electrolyte concentration (1 and 2 g/L), and initial concentration of Brilliant Blue dye (15 and 30 mg/L) on