This study aimed to investigate the influence of longitudinal steel embedded tubes located at the center of the column cross-section on the behavior of reinforced concrete (RC) columns. The experimental program consisted of 8 testing pin-ended square sectional columns of 150×150 mm, having a total height of 1400 mm, subjected to eccentric load. The considered variables were the steel square tube sizes of 25, 51 and 68 mm side dimensions and the load eccentricity (50 and 150) mm. RC columns were concealed steel tubes with hollow ratios of 3%, 12% and 20% depending on tube sizes used. The experimental results indicated an improvement in the overall behavior of eccentric columns when steel embedded tubes are used. The maximum gain in

In this study, an analytical model depending on experimental results for InPInGaAs
avalanche photodiode at low bias was presented and the characteristics of
gain for this photodiode were determined directly by the impulse response. The
model have considered the most important mechanisms contributing the
photocurrent, they are trapping, photogeneration in the undepleted region and
charge-carriers velocity due to the built-in electrical field. Also, the bandwidth
was determined as a function to the total gain of photodiode and it was mainly
determined by diffusion and trapping processes at low gain regarding to the multilayer
structure considered in this study

Many experiments were achieved to determine the allelopathic potential of the plant Myrtle parts in which it may affects other plants, like: volatile substances which released from the Myrtle leaves , and its effect examined on the germination (GE) and growth (GR) of the selected crops ; Chickpea ( C ) , Wheat(W) , and Lentil (L)., the aqueous extract of the leaf and the root of the plant examined to test its effect on the (GE) and (GR) of the selected crops ; (C) , (W) , and (L)., also plant residue of (M) and its effect tested on the (GE) and (GR) of the selected crops ; ( C ) , (W) , and (L) . Experiments proceeded on Spring 2007 in the greenhouse conditions , and main results which found were that; the effect of the volatile s

The efficiency of internal combustion engines (ICE) is usually about thirty percent of the total energy of the fuel. The residual energy is lost in the exhaust gas, the lubrication, and the cooling water in the radiators. Recently much of the researcher’s efforts have focused on taking advantage of wasted energy of the exhaust gas. Using a thermoelectric generator (TEG) is one of the promising ways. However, TEG depends entirely on the temperature difference, which may be offered by the exhaust muffler. An experimental test has been conducted to study the thermal performance of a different muffler internal design. The researchers resort to the use of lost energy in an ICE using TEG, which is one of the ways to take adv

The construction of embankment for roadway interchange system at urban area is restricted due to the large geometry requirements, since the value of land required for such construction is high, and the area available is limited as compared to rural area. One of the optimum solutions to such problem is the earth reinforcement technique which requires a limited area for embankment construction. Gypseous soil from Al-Anbar governorate area was obtained and subjected to various physical and chemical analysis to determine it is properties. A laboratory model box of 50x50x25 cm was used as a representative embankment; soil has been compacted in five layers at maximum dry density (modified compaction) and an aluminum reinforcement strips were i

A cantilever beam is made from composite material which is consist of (matrix: polyester) and (particles: Silicon-Carbide) with different volume fraction of particles. A force is applied at the free end of beam with different values. The experimental maximum deflection of beam which occurs at the point of the applied load is recorded. The deflection and slope of beam are analyzed by using FEM modeling. MATLAB paltform is built to assemble the equations, vector and matrix of FEM and solving the unknown variables (deflection and slope) at each node. Also ANSYS platform is used to modeling beam in finite element and solve the problem. The numerical methods are used to compare the results with the theoretical and experimental data. A good ag

KE Sharquie, WS Al-Dori, IK Sharquie, AA Al–Nuaimy, Hospital, 2004 - Cited by 20

After the fall of the Third Dynasty of Ur at the hands of the Elamites during the reign of its last ruler, King Ibi-Sin, the Amorites continued to flow more into Mesopotamia in the form of large migrations that established a number of contemporary and conflicting ruling dynasties that formed the Old Babylonian era. Among these dynasties was the Larsa dynasty, founded by King Nablanum in the city of Larsa. The fourth king who ruled in the Larsa dynasty, Gungunum, was one of the most powerful kings who stood up to the Isin dynasty, which had until that time enjoyed great political superiority in the country. The kings who ruled after him expanded their influence and controlled a number of cities, especially the cities of Nippur and Uruk, whic