This research is dealing with five sample of tomato ketchup products available in local market that were respectively as follows: Hello-Baghdad Iraq, Tiffany-Abu Dhabi, Melody-Dubai, Baidar-Saudi Arabia, and Altunsa-Turkey. Also it is dealing with four sample of sauce products available in local market that were respectively as follows: Hello-Baghdad, Iraq, Al-Badawi-Baghdad Iraq, Family-Baghdad, Iraq, and Hala-Amman Jordon. Analysis was performed on each sample three times and mean of the reading was taking. Samples were tested through terse and shorthand from lengthened steps. The spectrophotometric method used rely on theoretical and practical bases in extraction and diagnosis by UV spectrophotometer. This method in short notes, consisted of achievement of extraction of the ketchup and sauce aqueous solution in three steps from which benzoic acid extracted in the form of benzoate, through these steps the benzoate form was changed into benzoic acid form, so the sample aqueous solution extracted using diethyl ether and its quantity was transferred by volume. The UV absorbance curve for benzoic acid was drawn in spectral range 200-290 nm, and the spectra for benzoic acid 250-290 nm was also drawn, whereas in this range the higher absorbance at 272 nm was predicted, and the final benzoic acid solution was tested using UV spect. at this proper wavelength, so the benzoic acid reading was obtained using acid standard curve utilization. In this work was also noticed that pH values for ketchup and sauce products are differed and ranging from 2 to 5 instead of the stated values that must be between 3.5 to 4.7. The higher recorded benzoic acid concentrations in ketchup samples in this work was higher as 1315 and lower as 745 mg/Kg, and it recorded a value 255 mg/Kg which approaches allowable value stated by Iraqi standardization (250 mg/Kg). Whereas the higher recorded benzoic acid concentrations in sauce samples in this work was higher as 2695 mg/Kg, and some of which recorded a value 280 mg/Kg which approaches allowable value stated by Iraqi standardization (250 mg/Kg). In general terms the concentration levels in samples investigated were higher than allowable value stated by Iraqi standardization (250 mg/Kg).
Mixture experiments are response variables based on the proportions of component for this mixture. In our research we will compare the scheffʼe model with the kronecker model for the mixture experiments, especially when the experimental area is restricted.
Because of the experience of the mixture of high correlation problem and the problem of multicollinearity between the explanatory variables, which has an effect on the calculation of the Fisher information matrix of the regression model.
to estimate the parameters of the mixture model, we used the (generalized inverse ) And the Stepwise Regression procedure
... Show MoreTo prepare a new ligand, many compounds were used to synthesize Schiff-Mannich base, such as isatin, Para chloro Aniline, 2-mercaptobenzimidazole and indole. The resulting compound 1-((2-((1H-indol-1-ylthio)-1H-benzo[d]imidazol1-yl)methyl)-3-(4-chlorophenylimino)indolin-2-one (L). (L) was used to create a series of metal ion complexes with Co (II), Ni (II), Cu (II), Pd (II), Pt (IV), and Au (III). C.H.N.S., FTIR, mass spectra UV-ViS, 1H-NMR, 13CNMR, magnetic moment, and molar conductivity were used to characterize all of these compounds. Except for the palladium(II) and gold(III) complexes, all of the produced complexes had an octahedral geometry, according to the data. The antibacterial activity of the produced compounds was tested by usin
... Show MoreThe biggest problem of structural materials for fusion reactor is the damage caused by the fusion product neutrons to the structural material. If this problem is overcomed, an important milestone will be left behind in fusion energy. One of the important problems of the structural material is that nuclei forming the structural material interacting with fusion neutrons are transmuted to stable or radioactive nuclei via (n, x) (x; alpha, proton, gamma etc.) reactions. In particular, the concentration of helium gas in the structural material increases through deuteron- tritium (D-T) and (n, α) reactions, and this increase significantly changes the microstructure and the properties of the structural materials. T
... Show MoreOne of the most important phenomena facing the athlete is the anxiety of sports competition, as he faces many psychological problems during training and in competitions of psychological tension, fear and anxiety that accompany him sometimes, which leads to affecting his level, and sports competition anxiety is a special type of anxiety that occurs in the athlete It is related to the attitudes of sports competitions and that participation in sports competitions and the associated emotional experiences are among the important factors that motivate the practice of sports activity and try to advance and develop his sports level. It is assumed that when the individual begins to practice any activity, he aims to reach a level or degree of achie
... Show MoreObjective: To Evaluate the Roley of Cytotoxic T-Lymphocytek antigen 4 Polymorphism and soluble immune checkpoint level (PD-1,PDL-1 and CTLA-4 ) in SARS-Cov-2 patients. Methods: Fromt October 2020 to April 2021, the currentk study was conducted in Baghdad-Iraq. Ninety patients with Confirmatory SARS-Cov-2 by PCR were inclusion in the study, and they were seeking treatment at Medical City in Baghdad's Teaching Hospital (BTH). Patients with SARS-Cov-2 were divided into two groups: those with Sever SARS-Cov-2 symptom and those with mild - moderate SARS-Cov-2 symptoms (cross sectional study. Patients with another form of autoimmune illness, malignant, diabetes, under the age of 18 and pregnant women were excluded. Results: Data rega
... Show MoreIn this study, polymeric coating was developed by incorporating nano graphene in the polymer blend with applications to oil storage tanks. The oil storage tanks samples were brought from the oil Pipeline Company / Doura refinery in Baghdad. The coating polymer was formed with a blend (epoxy resin and repcoat ZR). The proportion of mixing the mixture was 3:1:1 epoxy resin 21.06 gm: repcoat ZR 10.53 gm: hardener 10.53 gm. The blend/graphene was prepared using in stui-polymerization method with different weight percentage 1, 3, 5, and 7 wt % added to blend. The resulting solution was put in a glass tube on a magnetic stirrer for one hour at a temperature of 40 °C. The result of contact angle and water absorption the best ratio of 3wt
... Show More