A total of 215 sheep and 87 goats were carefully searched for ixodid ticks from January to December 2015 at different regions of the middle and south of Iraq. The detached ticks count 1533 ticks from sheep with intensity of 8.4 and count 332 ticks from goats with intensity of 6.8. Tick species recovered from sheep and their incidence rates were: Rhipicephalus turanicus (39%), Hyalomma anatolicum (28%), R. (Boophilus) annulatus (11%), Hyalomma sp. (9%), H. turanicum (6%), H. excavatum (6%) and R. leporis (1%) while the tick species recovered from goats and their incidence rates were: R. turanicus (64%), H. anatolicum (24%)
... Show MoreTraditional nursing interventions for children with Cerebral Palsy (CP) often lack active engagement and show limited improvement in motor function. Play interventions involving manipulative activities may better support motor skill development. Objectives: To evaluate the effect of structured play-based nursing interventions on hand motor skills in children with cerebral palsy. Methods: A quasi-experimental pre-test/post-test design with a control group was used. The study was conducted at the Paediatric Welfare Hospital in Baghdad from November 25, 2024, to February 13, 2025. A non-probability sample of 79 children was identified based on the study criteria; of these, 64 children met the eligibility criteria and agreed to particip
... Show MoreIn this paper a stirred-bed performed of the copper catalyzed synthesis of ethylchlorosilanes from silicon and ethyl chloride was described. A Si-catalyst mixture prepared by reaction of CuCl and Si was employed. The compositions of products were mainly ethyltrichlorosilane, diethyldichlorosilane, and ethyldichlorosilane and mainly depended on the extent of Cu in the mixture and the reaction temperature. A promoting effect on the extent of adsorption was observed on the addition of certain additives. The kinetic data revealed the direct depended of the reaction rate on C2H5Cl pressure.
In this work, yttrium oxide particles (powder) reinforced AL-Si matrix composites (Y2O3/Al-Si) and Chromium oxide particles reinforced AL-Si matrix composites (Cr2O3/AL-Si) were prepared by direct squeeze casting. The volume percentages of yttrium oxide used are (4, 8.1, 12.1, 16.1 vol %) and the volume percentages of the chromium oxide particles used are (3.1, 6.3, 9.4, 12.5 vol. %). The parameters affecting the preparation of Y2O3/Al-Si and Cr2O3/AL-Si composites by direct squeeze casting process were studied. The molten Al-Si alloy with yttrium oxide particles or with chromium oxide particles was stirred again using an electrical stirrer at speed 500 rpm and the molten alloy was poured into the squeeze die cavity. Th
... Show MoreKarst aquifers in semi-arid regions are vital yet exceptionally vulnerable lifelines. This study investigates how tectonic, geomorphological, and climatic factors control the dynamics of karst springs in the El Menzel Causse (Middle Atlas, Morocco). Using an integrated approach that combines field investigations, remote sensing, and quantitative hydro-climatic analysis, we identify the mechanisms driving the system’s severe decline. Results indicated that the structural architecture of the major fault systems in the North Middle Atlas Fault (NMAF) and the Median Middle Atlas Fault (MMAF), governs the spatial distribution of more than 50 springs, which occur preferentially within highly permeable fault damage zones. However, the aquifer is
... Show More
A numerical study has been carried out to investigate heat transfer by natural convection and radiation under the effect of magnetohydrodynamic (MHD) for steady state axisymmetric twodimensional laminar flow in a vertical cylindrical channel filled with saturated porous media. Heat is generated uniformly along the center of the channel with its vertical surface remain with cooled constant wall temperature and insulated horizontal top and bottom surfaces. The governing equations which used are continuity, momentum and energy equations which are transformed to dimensionless equations. The finite difference approach is used to obtain all the computational results using the MATLAB-7 programming. The parameters affected on the system are Rayl
... Show More