The study was conducted at the fields of the Dept. of Horticulture and Garden Engineering, College of the Agricultural Engineering Sciences, Jadriyah in the fall season of 2020-2021 aiming to culture the coral lettuce with green and red leaves under the hydroponics system using the modified nutrient solution film NFT and study the effect of aqueous extracts of alfalfa and berseem sprouted seeds on the quantitative and qualitative yield of the lettuce crop. The research was conducted as an experiment of split plots within the Randomized Complete Block Design (RCBD) of three replicates. The seedlings of the green coral lettuce, Locarno RZ, and red coral lettuce, Locarno RZ, symbolized by A and B respectively, were transferred to the culture system on 1/10/2020. Lettuce hybrids were regarded as the less important factor (main plot). The plants were sprayed with aqueous extracts of the alfalfa sprouted seeds at the two concentrations of 5 and 10%, symbolized by T1 and T2, and with aqueous extracts of the berseem sprouted seeds at the two concentrations of 5 and 10%, symbolized by T3 and T4, respectively, in addition to the control treatment (spraying with distilled water only), symbolized by T0. They were sprayed to full wetness three times at an interval of 10 days. This was regarded as the most important factor (subplot). Each experimental unit contained 10 plants. Results showed significant superiority of the treatment AT2 in the leaf chlorophyll content, number of leaves, leaf area and dry weight of vegetative growth (80.00 mg.100g fresh weight-1, 37.00 leaf.plant-1, 144.05 dcm2.plant-1, 10.97 g.plant-1 respectively) compared to the lowest value of the treatment BT0 (60.56 mg.100g fresh weight-1, 19.00 leaf.plant-1, 63.32 dcm2.plant-1 and 5.65g.plant-1 respectively). The same treatment (AT2) was superior in the highest root dry weight, and plant yield amounted to 1.92 and 364.35g.plant-1, respectively compared to the lowest values at the treatment AT0, recording 0.75 and 219.92g.plant -1 respectively. The interaction treatments' effect was insignificant on the content of β-carotene and VC in the leaves. We concluded that it is possible to culture the coral lettuce hydroponically and increase its productivity through spraying with the aqueous extracts of the alfalfa sprouted seeds at the concentration of 5%, which did not record a significant difference in the production from the treatment of spraying with aqueous extracts of the alfalfa sprouted seeds at 10%. Keywords: Lactuca sativa L., Red lettuce, Organic nutrients, Plant extracts, Soil culture.
he effect of different cultural conditions on production of bioemulsifier from Serratia marcescens S10 was determined; different carbon and nitrogen sources were used such as: different oils include: edible (vegetable) oils (olive oil, sesame oil, sun flower oil and corn oil) and heavy oils (oil 150, oil 60, oil 40) as carbon sources and (NH4Cl, casein, (NH4)2SO4, peptone, tryptone, gelatin and yeast extract) as nitrogen sources were added to production media. Bioemulsifier was estimated by measuring the surface tension (S.T), emulsification activity (E.A) and emulsification index (E24%). The best results of bioemulsifier production from Serratia marcescens S10 were obtained at pH8 and incubated at 37ºC for 5days, using sesame oil
... Show MoreA polycrystalline PbxS1-x alloys with various Pb content ( 0.54 and 0.55) has been prepared successfully. The structure and composition of alloys are determined by X-ray diffraction (XRD), atomic absorption spectroscopy (AAS) and X-ray fluorescence (XRF) respectively. The X-ray diffraction results shows that the structure is polycrystalline with cubic structure, and there are strong peaks at the direction (200) and (111), the grain size varies between 20 and 82 nm. From AAS and XRF result, the concentrations of Pb content for these alloys were determined. The results show high accuracy and very close to the theoretical values. A photoconductive detector as a bulk has been fabricated by taking pieces of prepared alloys and polished chemic
... Show MoreIn this paper, we used two monomers, 3,3',4,4'-benzophenone tetracarboxylic dianhydride (BTDA) and m,m'-diaminobenzophenone (m, m’-DABP), to produce polyamide acid and then converted it to polyimide (PI). The effects of phosphoric acid (H3PO4) molarity (1, 2, and 3 M) on the structural, thermal, mechanical, and electrical characteristics of the polyimides/polyaniline (PI/PANI) nanocomposites were studied. Two sharp reflection peaks were developed by the addition of PANI to PI. When 3 M H3PO4 is added, the crystalline sharp peak loses some of its intensity. The complex formation of PI/PANI-H3PO4 was confi
... Show MoreThis study examined the effect of essential oils extracted from peel of Citrus paradisi and Citrus sinensis on two species of fungi: Penicillium oxalicum and Fusarium oxysporum as well as effect of two fungicides: Carbendazim and Thiophanatemethyl against above fungi. Results showed that the essential oil of Citrus paradisi inhibited the radial growth of Penicillium oxalicum and Fusarium oxysporum at concentration 4%. Nevertheless, the essential oil of Citrus sinensis inhibited the radial growth at concentration 5 and 4%, respectively. Furthermore, the two studied fungicides inhibited radial growth of these fungi too. Therefore, there are a positive relationship between the evaluating of concentration and the percentage of inhibiting of rad
... Show MoreThis paper presents the study and analysis, analytically and numerical of circular cylindrical shell pipe model, under variable loads, transmit fluid at the high velocity state (fresh water). The analytical analysis depended on the energy observation principle (Hamilton Principle), where divided all energy in the model to three parts , strain energy, kinetic energy and transmitted energy between flow and solid (kinetic to potential energy). Also derive all important equations for this state and approach to final equation of motion, free and force vibration also derived. the relations between the displacement of model function of velocity of flow, length of model, pipe thickness, density of flowed with location coordinate x-axis and angle
... Show More