A real method of predication brake pad wear ,could lead to substantiol economies of time and money. This paper describes how such a procedure has been used and gives the results to establish is reliability by comparing the predicted wear with that which actually occurs in an existing service. The experimental work was carried out on three different commercial samples ,tested under different operation conditions (speed,load,time...etc)using a test ring especially modified for this purpose. Abrasive wear is mainly studied , since it is the type of wear that takes place in such arrangements. Samples wear tested in presences of sand or mud between the mating surfaces under different operational conditions of speed, load and braking time .Mechanical properties of the pad material samples (hardness, young,s modulus and collapse load under pure bending condition )wear established . The thermal conductivity and surface roughness of the pad material wear also found in order to enable comparison between the surface condition before and after testing. Sliding velocity had a small effect on the wear rate but it had great effect on friction coefficient. Wear rate was affected mainly by the surface temperature which causing a reduction friction coefficient and increasing the wear rate. Surface roughness had almost no effect on the wear rate since it was proved experimentally ,that the surface becomes softer during operation .mechanical properties of the pad material had fluctuating effect on wear rate. The existence of solid particles between pad and disc increasing wear rate and friction coefficient while the mud caused a reduction in wear rate of the pad surface since it acts as a lubricant absorbing the surface heat generated during sliding the area of contact between pad and disc. wear rate obtained experimentally agreed fairly well that found from empirically obtained equations.
(9)
(9)
The need to overcome the failure of orthodontic micro-implants which might reach to 30% has led to the development of different methods, one of which is nanoparticle deposition.
To evaluate the anti-microbial efficiency of TiO2 and ZnO nanoparticles (NP) when used as a coating for orthodontic micro-implants.
Thirty titanium alloy micro-implants were used in the presented study. They were divided into three
(5)
(5)
بعد مرور عام واكثر على ظهور فيروس كورونا والعالم يواجه تسونامي تلك الجائحة التي تكاد تعصف بالوجود البشري برمته لذا اخذت البشرية على عاتقها مواصلة الجهود والابحاث للوصول الى علاج طبي يتم من خلاله مواجهة هذا الفيروس او التقليل من آثاره التي تهدد الحياة البشرية بالموت المباشر دون الاصابة، مما نتج عن تلك الجهود مجموعة من اللقاحات التي تبنتها الشركات العالمية المسؤولة الا ان الضرورة القصوى التي نتجت عنها تلك الل
... Show MoreThere are no single materials which can withstand all the extreme operating conditions in modern technology. Protection of the metals from hostile environments has therefore become a technical and economic necessity.
In this work, for enhancing their wear-resistance, boride layers were deposited on the surface of low carbon steel by a pack cementation method at 850 °C for (2, 4, and 6) h using vacuum furnace. The boronizing process was achieved using different concentration of boron source (20, 25, and 30) % wt. into coating mixture to optimize the best conditions which ensure the higher properties with lower time. The coating was characteristic by X ray diffraction (XRD), and it is confirmed t
... Show More
(4)
(3)
Iraq has seen many changes at the social, economic and political levels. This led to cause many shifts in the structure of its society and imposed great challenges reflected in the behavior and awareness of that society in general and youth in particular.
Those changes made the Iraqi society undergoing the transformation of value and culture aspects formed a political awareness that caused cultural and political diversity within the family and society. A greater openness to the outside world caused by the communication revolution, as the world has witnessed during the past two decades, has helped in making that change. Iraq had its share of media and political openness, which were included after the US occupation in 2003. As a re
... Show More
This paper deals with the nations of British American Struggle in Caribbean. It
explains British Navy attitude of American expansion in Caribbean. Then continuation of
American expansion in the same place and Britain failure to limit it. This paper high lights the
beginning of acceptance between Britain's and United state, especially after British
submission to United States in Caribbean. Then we study the Anglo – American harmony and
the affection on the Anglo – American relation.
This paper concludes that American influences in Americans which is a truth.
The research tries to discuss the European attitude towards the Iranian nuclear
activities withen its ambitious nuclear program. It studies the European endeavor to settle
this problem peacefully or to solve it by exerting economic and diplomatic pressures on the
Iranian leadership so, it will give up its nuclear ambitions.
Germany exerts single efforts and others withen the European Troika to follow up
the Iranian nuclear case attempting to prevent Iran from acquiring nuclear weapon which
gives Iran a distinguished regional status. Thus , this situation will lead the current regional
equivalence become unbalanced as well as it is conducive to dangerous consequences , to
endanger the security of Israel is the most
Background: Because of the demands for aesthetic orthodontic appliances have increased, aesthetic archwires have been widely used to meet patient's aesthetic needs. The color stability of aesthetic archwires is clinically important, any staining or discoloration will affect patient’s acceptance and satisfaction. This study was designed to evaluate the color stability of different types of aesthetic archwires after immersion into different types of mouth washes. Materials and methods: Four brands of nickel titanium coated aesthetic arch wires: Epoxy coated (Orthotechnology and G&H) and Teflon coated (Dany and Hubit) were evaluated after 1 week, 3 weeks and 6 weeks of immersion into two types of mouthwashes (Listerine with alcohol and
... Show More
(2)