A real method of predication brake pad wear ,could lead to substantiol economies of time and money. This paper describes how such a procedure has been used and gives the results to establish is reliability by comparing the predicted wear with that which actually occurs in an existing service. The experimental work was carried out on three different commercial samples ,tested under different operation conditions (speed,load,time...etc)using a test ring especially modified for this purpose. Abrasive wear is mainly studied , since it is the type of wear that takes place in such arrangements. Samples wear tested in presences of sand or mud between the mating surfaces under different operational conditions of speed, load and braking time .Mechanical properties of the pad material samples (hardness, young,s modulus and collapse load under pure bending condition )wear established . The thermal conductivity and surface roughness of the pad material wear also found in order to enable comparison between the surface condition before and after testing. Sliding velocity had a small effect on the wear rate but it had great effect on friction coefficient. Wear rate was affected mainly by the surface temperature which causing a reduction friction coefficient and increasing the wear rate. Surface roughness had almost no effect on the wear rate since it was proved experimentally ,that the surface becomes softer during operation .mechanical properties of the pad material had fluctuating effect on wear rate. The existence of solid particles between pad and disc increasing wear rate and friction coefficient while the mud caused a reduction in wear rate of the pad surface since it acts as a lubricant absorbing the surface heat generated during sliding the area of contact between pad and disc. wear rate obtained experimentally agreed fairly well that found from empirically obtained equations.
Release of industrial effluents comprising dyes in water bodies is one of the foremost causes of water pollution. Therefore, the proper and proficient treatment of these dyes contaminated left-over material before their release is crucial. Herein, an eco-friendly biological macromolecule Gum-Acacia (GA) integrated Fe3O4 nanoparticles composite hydrogel was manufactured via co-precipitation technique for effective adsorption of Congo red (CR) dye existing in water bodies. The as-prepared magnetic GA/Fe3O4 composite hydrogel was characterized by FTIR, XRD, EDX, VSM, SEM, and BET techniques. These studies discovered the fruitful fabrication of biodegradable magnetic GA/Fe3O4 composite hydrogel possessing porous structure with large surface are
... Show More
(23)
(20)
Sensibly highlighting the hidden structures of many real-world networks has attracted growing interest and triggered a vast array of techniques on what is called nowadays community detection (CD) problem. Non-deterministic metaheuristics are proved to competitively transcending the limits of the counterpart deterministic heuristics in solving community detection problem. Despite the increasing interest, most of the existing metaheuristic based community detection (MCD) algorithms reflect one traditional language. Generally, they tend to explicitly project some features of real communities into different definitions of single or multi-objective optimization functions. The design of other operators, however, remains canonical lacking any inte
... Show More
(77)
(55)
(36)
(27)
(10)
(6)
Detecting the optimum layer for well placement, which requires a diverse assortment of tools and techniques, represents a significant challenge in petroleum studies due to its critical impact on minimizing drilling costs and time. This study aims to evaluate integrated geological, petrophysical, seismic, and geomechanical data to identify the optimum zones for well placement. Three different reservoirs were analyzed to account for lateral and vertical variations in reservoir properties. The integrated data from these reservoirs provides many tools for reservoir development, especially to detect appropriate well placement zones based on evaluations of reservoir and geomechanical quality. The Mechanical Earth Model (MEM) was construct
... Show More
New derivatives of Schiff bases were synthesized from the aldehyde derivative (Ma2) which was produced by reacting the mefenamic acid (Ma) with thionyl chloride to obtain the acid halide derivative (Ma1). Compound (Ma1) was dissolved in DMF and mixed with p-hydroxybenzaldehyde which was previously dissolved with pyridine to obtain the aldehyde derivative (Ma2). In the final step, derivatives of Schiff bases were synthesized by reacting the aldehyde (Ma2) with a number of different aromatic primary amines in the presence of glacial acetic acid to obtain the new derivatives Ma [3-10]. The new prepared compounds were characterized by melting points and with spectral data FT-IR, 13C-NMR and 1H-MNR (some of them). The vital effectiven
... Show MoreAn experiment was conducted in pots under field conditions during fall seasons of 2017 and 2018. This study aimed to improve a weak growth of seedlings under salt stress in sorghum. Three factors were studied. 1st factor was three cultivars (Inqath, Rabeh, and Buhoth70). 2nd factor was seed priming (primed and unprimed seed). Seed were primed by soaking for 12 hours in a solution containing 300 + 70 mg L−1 of gibberellic (GA3) and salicylic (SA) acids, respectively. 3rd factor was irrigation with saline water (6, 9 and 12 dS m−1) resulting from dissolving sodium chloride in distilled water in addition to control treatment (distilled water). Randomized complete block design was used with four replications. In both seasons: the results sh
... Show More
(32)
(25)
The electrochemical polymerization of the monomer sulfanilamide (SAM) in an aqueous solution at room temperature produces polysulfanilamide (PSAM). The Fourier Transform Infrared spectroscopy (FTIR) was used to investigate the properties of the prepared polymer layer that generated on the stainless steel (St.S) surface (working electrode) and Atomic Force Microscope (AFM) was used to characterize the morphology, topology, and detailed surface structure of polymer layer that generated on the surface. The corrosion behavior of uncoated and coated St.S were evaluated by using the electrochemical polarization method in a 0.2 M HCl solution and a temperature range of 293–323 K, the anticorrosion action of the polymer coating on stainless steel
... Show More
(10)
Objectives Acid sphingomyelinase deficiency (ASMD) is an inherited autosomal recessive disease caused by pathogenic variants in the sphingomyelin phosphodiesterase-1 (SMPD1) gene, which encodes acid sphingomyelinase (ASM). ASMD has 3 broad phenotypes (type A, type A/B, and type B) characterized by the age of onset, symptomatology, and the rapidity of disease progression. The diagnosis of ASMD can be delayed or missed because of the wide spectrum of severity and its variable manifestations. Analysis of genotype-phenotype correlations can help to determine ASMD disease type and inform management. Here, we describe the clinical presentation of 47 patients with ASMD referred to a single center in Iraq since 2007, whose diagnosis was confirmed b
... Show More
Background: Colorectal cancer, the most common gastrointestinal cancer, is a significant health issue globally. Mucin 16 plays a critical role in cancer signal transduction pathways and is a potential glycoprotein target for cancer therapy. The miRNA-200 family also regulates the expression of numerous genes that play vital roles in cancer cells. This study aimed to investigate the changes in mucin 16 and miRNA-200a in patients with colorectal cancer (CRC). Subjects and Methods: Fifty-six patients with CRC, including 26 in stage 3 and 30 in stage 4, were included in this study, along with 38 healthy volunteers as a control group. Parameters such as mucin 16, miRNA-200a, total protein, albumin, globulin, and the albumin/globulin rati
... Show More