The alloys of CdSe1-xTex compound have been prepared from their elements successfully with high purity (99.9999%) which mixed stoichiometry ratio (x=0.0, 0.25, 0.5, 0.75 and 1.0) of (Cd, Se and Te) elements. Films of CdSe1-xTex alloys for different values of composition with thickness(0.5?m) have been prepared by thermal evaporation method at cleaned glass substrates which heated at (473K) under very low pressure (4×10-5mbar) at rate of deposition (3A?/s), after that thin films have been heat treated under low pressure (10-2mbar) at (523K) for two hours. The optical studies revealed that the absorption coefficient (?) is fairly high. It is found that the electronic transitions in the fundamental absorption edge tend to be allowed direct tr

    The plant Abrus precatorius, which belong to Leguminosae (Fabaceae) family and known as Crab’s eyes, Rosary pea with characteristic red and black seeds. It was used in folk medicine in India, China and East Asian countries for treatment of various diseases.

   The plant was extracted by '' general method of extraction'' (Harborne, 1973) using 80% aqueous ethanol as a solvent of extraction by soxhlet apparatus. Preliminary qualitative phytochemical screening were performed on the crude ethanolic extract  and revealed the presence of alkaloids, flavonoids ,terpenoids and phytosterols in Iraqi Abrus pr

    The plant Abrus precatorius, which belong to Leguminosae (Fabaceae) family and known as Crab’s eyes, Rosary pea with characteristic red and black seeds. It was used in folk medicine in India, China and East Asian countries for treatment of various diseases.    The plant was extracted by '' general method of extraction'' (Harborne, 1973) using 80% aqueous ethanol as a solvent of extraction by soxhlet apparatus. Preliminary qualitative phytochemical screening were performed on the crude ethanolic extract  and revealed the presence of alkaloids, flavonoids ,terpenoids and phytosterols in Iraqi Abrus precatorius plant. Three different fractions were obtained from crude extract which are fraction one (chloroform fractio

This study investigated the feasibility of anaerobic co-digestion of giant reed (GR) inoculated with waste manure as a co-substrate for biogas production. The performance of co-digestion was evaluated in 4 anaerobic digesters operated in batch mode at different conditions. The effects of alkali pretreatment with NaOH (4% w/v) solution, inoculum type, and thermal condition were studied. The results demonstrated that the alkali-pretreatment of GR enhanced the biogas generation by about 15% at mesophilic conditions. Thermophilic conditions enhanced the biogas recovery from both alkali-free and alkali pretreated GR by 15% and 127%, respectively. The kinetic study of the co-digestion process of GR for biogas recovery suggeste

ABSTRACT                                                                                            

The study aims to identify the level of health services provided in private suites to government hospitals from the perspective of the recipi

Indirect electrochemical oxidation of phenol and its derivatives was investigated by using MnO₂ rotating cylinder electrode. Taguchi experimental design method was employed to find the best conditions for the removal efficiency of phenol and its derivatives generated during the process. Two main parameters were investigated, current density (C.D.) and electrolysis time. The removal efficiency was considered as a response for the phenol and other organics removal. An orthogonal array L₁₆, the signal to noise (S/N) ratio, and the analysis of variance were used to test the effect of designated process factors and their levels on the performance of phenol and other organics removal efficiency. The results showed that th

Electrical Discharge Machining (EDM) is a non-traditional cutting technique for metals removing which is relied upon the basic fact that negligible tool force is produced during the machining process. Also, electrical discharge machining is used in manufacturing very hard materials that are electrically conductive. Regarding the electrical discharge machining procedure, the most significant factor of the cutting parameter is the surface roughness (Ra). Conventional try and error method is time consuming as well as high cost. The purpose of the present research is to develop a mathematical model using response graph modeling (RGM). The impact of various parameters such as (current, pulsation on time and pulsation off time) are studied on