The main objective of this research is to design and select a composite plate to be used in fabricating wing skins of light unman air vehicle (UAV). The mechanical properties, weight and cost are the basis criteria of this selection. The fiber volume fraction, fillers and type of fiber with three levels for each were considered to optimize the composite plate selection. Finite element method was used to investigate the stress distribution on the wing at cruise flight condition in addition to estimate the maximum stress. An experiments plan has been designed to get the data on the basis of Taguchi technique. The most effective parameters at the process to be find out by employing L9 (33) orthogonal array, signal to noise ratio (S/N), main effect and analysis of variance (ANOVA). The results show that, the experimental and the predicted results are very close. It was found that the type of fiber is the most effective parameter on the plate selection, followed by filler content and then the fiber volume fraction. The best parameters combinations are ((E-glass woven roving + unidirectional carbon) fiber, 7.5% graphite filler and 30% fiber volume fraction). This combination provides good mechanical properties, high safety factor, acceptable cost, and offers weight savings on average by 40% percent as compared to aluminum alloy.
The objective of this work is to investigate the performance of a conventional three phase induction motor supplied by unbalanced voltages. An effort to study the motor steady state performance under this disturbance is introduced. Using per phase equivalent circuit analysis with the concept of symmetrical components approach, the steady state performance is theoretically calculated. Also, a model for the induction motor with the MATLAB/Simulink SPS tools has been implemented and steady state results were obtained. Both results are compared and show good correlation as well. The simulation model is introduced to support and enhance electrical engineers with a complete understanding for the steady state performance of a fully loaded induc
... Show MoreA polycrystalline CdSe thin films doped with (5wt%) of Cu was fabricated using vacuum evaporation technique in the substrate temperature range(Ts=RT-250)oC on glass substrates of the thickness(0.8?m). The structure of these films are determined by X-ray diffraction (XRD). The X-ray diffraction studies shows that the structure is polycrystalline with hexagonal structure, and there are strong peaks at the direction (200) at (Ts=RT-150) oC, while at higher substrate temperature(Ts=150-250) oC the structure is single crystal. The optical properties as a function of Ts were studied. The absorption, transmission, and reflection has been studied, The optical energy gap (Eg)increases with increase of substrate temperature from (1.65
... Show MoreThe study aimed to identify the psychological counseling skills and the strength of the ego in the educational counselors, and to identify the relationship of statistical significance between the psychological counseling skills and the strength of the ego in the educational counselors, and to identify the differences of statistical significance in the relationship between psychological counseling skills and the strength of the ego in the guides according to the gender variable(male, Females), the number of sample (100) guides, including (50) males and (50) females from the area of Atifiya and Qadissiya and Ameriya in the Directorate of Education Karkh / 1, the researcher adopted a scale of psychological counseling skills prepared b
... Show MoreThe preparatory phase since it corresponds to adolescence are the most important stages of life , where the individual 's personality to take shape at this stage and start asking questions about the same , trying to discover the positive and negative traits hehas in order to form distinctive character and also is being he have Love Poll For everything that goes on around him.
And attention to cognitive motivation is important for students because the student who owns a motive cognitively looking for self - knowledge with conviction, and learning then be meaningful and lasts long. The motive of knowledge are common in which cognitive components does not mean exclusive knowledge on academic books and research in the narrow borders but a
Tira is a custom known to the Arabs since the pre-Islamic era. in the occurrence of good or evil. And from the pessimism: that the Arabs in the pre-Islamic era depended on birds, so if one of them went out for a matter, If he sees a bird flying to the right, he will believe in him and go on his journey and his need. The research aims to introduce Imam Al-Manawi and explain his saying in Al-Tira through his book Fayd Al-Qadeer.
Abu Al-Ala Al-Ma’arri is a linguist and writer who showed his prowess in poetry, so he had poetry collections, including “The ulna fell,” which is one of the books that attracted the attention of scholars such as (Tabrizi, Al-Khwarizmi, Al-Bateliusi and Al-Zamakhshari) .
To explain his language in it, the investigators’ hands finally revealed an explanation of this book, which was the work of Abu Al-Ala Al-Ma’arri himself. Those who studied the Divan (The Zind) and its explanations or the character and language of Al-Ma’arri did not pay any attention to it. Therefore, I made this research a continuation of those efforts, using semantic research as a means of revealing Al-Maarri's ef
... Show MoreSecure information transmission over the internet is becoming an important requirement in data communication. These days, authenticity, secrecy, and confidentiality are the most important concerns in securing data communication. For that reason, information hiding methods are used, such as Cryptography, Steganography and Watermarking methods, to secure data transmission, where cryptography method is used to encrypt the information in an unreadable form. At the same time, steganography covers the information within images, audio or video. Finally, watermarking is used to protect information from intruders. This paper proposed a new cryptography method by using thre
... Show MoreA research was conducted to determine the feasibility of using adsorption process to remove boron from aqueous solutions using batch technique. Three adsorbent materials; magnesium, aluminum and iron oxide were investigated to find their abilities for boron removal. The effects of operational parameters on boron removal efficiency for each material were determined.
The experimental results revealed that maximum boron removal was achieved at pH 9.5 for magnesium oxide and 8 for aluminum and iron oxide. The percentage of boron adsorbed onto magnesium,aluminum and iron oxide reaches up to 90, 42.5 and 41.5% respectively under appropriate conditions. Boron concentration in effluent water after adsorption via magnesium oxide comply with th