This work studies with produce of light fuel fractions of gasoline, kerosene and gas oil from treatment of residual matter that will be obtained from the solvent extraction process as by product from refined lubricate to improve oil viscosity index in any petroleum refinery. The percentage of this byproduct is approximately 10% according to all feed (crude oil) in the petroleum refinery process. The objective of this research is to study the effect of the residence time parameter on the thermal cracking process of the byproduct feed at a constant temperature, (400 °C). The first step of this treatment is the thermal cracking of this byproduct material by a constructed batch reactor occupied with control device at a selective range of re

Thin films samples of Bismuth sulfide Bi2S3 had deposited on
glass substrate using thermal evaporation method by chemical
method under vacuum of 10-5 Toor. XRD and AFM were used to
check the structure and morphology of the Bi2S3 thin films. The
results showed that the films with law thickness <700 nm were free
from any diffraction peaks refer to amorphous structure while films
with thickness≥700 nm was polycrystalline. The roughness decreases
while average grain size increases with the increase of thickness. The
A.C conductivity as function of frequency had studied in the
frequency range (50 to 5x106 Hz). The dielectric constant,
polarizability showed significant dependence upon the variation of
thic

Electrical Discharge Machining (EDM) is a widespread Nontraditional Machining (NTM) processes for manufacturing of a complicated geometry or very hard metals parts that are difficult to machine by traditional machining operations. Electrical discharge machining is a material removal (MR) process characterized by using electrical discharge erosion. This paper discusses the optimal parameters of EDM on high-speed steel (HSS) AISI M2 as a workpiece using copper and brass as an electrode. The input parameters used for experimental work are current (10, 24 and 42 A), pulse on time (100, 150 and 200 µs), and pulse off time (4, 12 and 25 µs) that have effect on the material removal rate (MRR), electrode wear rate (EWR) and wear ratio (WR). A

  This work reports the study of heat treatment effect on the structural, morphological, optical and electrical properties of poly [3-hexylthiophene] and its blend with [6,6]-phenyl C61 butyric acid methyl ester ( P3HT:PC61BM). X-ray diffraction (XRD) measurements show that the crystallinity of the films increased with annealing. The evaluation of surface roughness and morphology was investigated using atomic force microscope (AFM), and field emission scanning microscope(FESEM). The optical properties were emphasized a strong optical absorption of P3HT compared with the blend. Hall effect measurement was used to study the electrical properties which revealed there is an increase in the electrical conductivity and Hall mobility of th

The performance and lifetime of the flexible asphalt pavement are mainly dependent on the interfacial bond strength between layer courses. To enhance the bond between layers, adhesive materials, such as tack coats, are used. The tack coat itself is a bituminous material, which is applied on an existing relatively non-absorbent surface to ensure a strong bond between the old and newly paved layer. The primary objective of this study was to evaluate the effects of various types of tack coat materials on interlayer bond strength and to determine the optimal application rate for each type. The tack coat types used in this paper were RC-70, RC-250, and CSS-1h. Both laboratory-prepared and field-constructed hot mix asphalt concrete pavements usin

Background: The aims of this study were to evaluate the effect of implant site preparation in low-density bone using osseodensification method in terms of implant stability changes during the osseous healing period and peri-implant bone density using CBCT. Material and methods: This prospective observational clinical study included 24 patients who received 46 dental implants that were installed in low-density bone using the osseodensification method. CBCT was used to measure the bone density pre- and postoperatively and implant stability was measured using Periotest® immediately after implant insertion and then after 6 weeks and 12 weeks postoperatively. The data were analyzed using paired t-test and the probability value <0.05 was conside

􀀨􀀅􀀆􀀔􀀜􀀄􀀂􀀆􀀈􀀓􀀌􀀩􀀏􀀆􀀉􀀅􀀆􀀉􀀅􀀉􀀚􀀝􀀔􀀄􀀗􀀉􀀚􀀆􀀂􀀓􀀚􀀁􀀔􀀄􀀓􀀅􀀆􀀄􀀂􀀆􀀔􀀓􀀆􀀃􀀂􀀔􀀄􀀟􀀉􀀔􀀃􀀆􀀔􀀜􀀃􀀆􀀛􀀃􀀜􀀄􀀗􀀚􀀃􀀆􀀗􀀌􀀄􀀔􀀄􀀗􀀉􀀚􀀆􀀂􀀘􀀃􀀃􀀊􀀂􀀆􀀓􀀖􀀆􀀓􀀛􀀃􀀌􀀔􀀁􀀌􀀅􀀄􀀅􀀕􀀢􀀆􀀪􀀜􀀃􀀆􀀄􀀅􀀛􀀃􀀂􀀔􀀄􀀕􀀉􀀔􀀄􀀓􀀅􀀂􀀆 􀀉􀀌􀀃􀀆􀀙􀀉􀀂􀀃􀀊􀀆􀀓􀀅􀀆􀀉􀀁􀀔􀀓􀀟􀀓􀀙􀀄􀀚􀀃􀀆􀀚􀀉􀀔􀀃􀀌􀀉􀀚􀀆􀀂􀀘􀀉􀀗􀀃􀀆􀀟􀀄􀀊􀀂􀀔􀀆􀀔􀀜􀀃􀀆􀀗􀀃􀀅􀀔􀀃􀀌􀀚􀀄􀀅􀀃􀀂􀀆􀀓􀀖􀀆􀀔􀀜􀀃􀀆􀀙􀀉􀀂􀀃􀀆

Increasing the variety of products that are being designed with sculptured surfaces, efficient machining of these surfaces has become more important in many manufacturing industries. The objective of the present work is the investigation of milling parameters for the sculptured surfacesthat effecting of surface roughness during machining of Al-alloy. The machining operation implemented on C-TEK CNC milling machine. The influence of the selected variables on the chosen characteristics have been accomplished using Taguchi design approach, also ANOVA had been utilized to evaluate the contributionsof each parameter on proc