The Halabja earthquake occurred on 12/11/2017 in Iraq, with a magnitude of 7.3 Mw, which happened in the Iraqi-Iranian borders. This earthquake killed and injured many people in the Kurdish region in the north of the country. There is no natural disaster more dangerous than earthquake, especially it occurs without warning, great attention must be paid to the impact of earthquakes on the soil and preparing for a wave of earthquakes. Numerical modeling using specific elements is considered a powerful tool to investigate the required behavior of structures in Geotechnical engineering, and the main objective of this is to assess the response of the Al-Wand dam to the Halabja earthquake, as this dam is located in an area that has been subjected to seismic activity recently. The modeling was done through the Geo-studio program, where the seepage was analyzed during the Al-wand dam using the Seep/w program. It was verified that the dam was safe against seepage failure and then moved to the QUAKE/W (a subprogram of GEOSTUDIO, which is used for liquefaction modeling of earthquakes and dynamic loading and determines the movement and increased pressures of pore water that arise due to earthquake vibration or sudden shock loads). The program was used to analyze the effect of the earthquake on the porewater pressure, effective stresses, and displacements. Also, it is not clear that the significant impact the earthquake has on these values. Finally, the Slope/w program was used to analyze the stability of the dam and to calculate the safety factor of the dam in two ways, and the results of the analysis show that the dam is considered safe under the influence of the tremor.
Abstract: Despite the distinct features of the continuous wave (CW) Terahertz (THz) emitter using photomixing technique, it suffers from the relatively low radiation output power. Therefore, one of effective ways to improve the photomixer emitter performance was using nanodimensions electrodes inside the optical active region of the device. Due to the nanodimension sizes and good electrical conductivity of silver nanowires (Ag-NWs), they have been exploited as THz emitter electrodes. The excited surface plasmon polariton waves (SPPs) on the surface of nanowire enhances the incident excitation signal. Therefore, the photomixer based Ag-NW compared to conventional one significantly exhibits higher THz output signal. In thi
... Show MoreSpray pyrolysis technique (SPT) is employed to synthesize cadmium oxide nanostructure with 3% and 5% Cobalt concentrations. Films are deposited on a glass substrate at 350 ᵒC with 150 nm thickness. The XRD analysis revealed a polycrystalline nature with cubic structure and (111) preferred orientation. Structural parameters represent lattice spacing, crystallite size, lattice parameter and dislocation density. Homogeneous surfaces and regular distribution of atoms were showed by atomic force microscope (AFM) with 1.03 nm average roughness and 1.22 nm root mean square roughness. Optical properties illustrated a high transmittance more than 85% in the range of visible spectrum and decreased with Co concentration increasing. The absorption
... Show MoreGold, silver and nickel used as electrodes in the fabrication of perovskite solar cell by using thermal evaporation deposition method with direct structure FTO\ TiO2\ MAPbI3\ spiro-MeOTAD\ metal electrode. The cell efficiency was compared between the electrodes material as a function of time to explaining the effect of these metals electrode on cell performance, X-ray diffraction pattern showed that the samples that contain gold and nickel do not contain a compound indicating the interaction of the metal with the components of the cell or the formation of a new compound, while in the cell containing silver it was found that silver iodide is fo
Background: The aims of this study were to evaluate the effect of implant site preparation in low-density bone using osseodensification method in terms of implant stability changes during the osseous healing period and peri-implant bone density using CBCT. Material and methods: This prospective observational clinical study included 24 patients who received 46 dental implants that were installed in low-density bone using the osseodensification method. CBCT was used to measure the bone density pre- and postoperatively and implant stability was measured using Periotest® immediately after implant insertion and then after 6 weeks and 12 weeks postoperatively. The data were analyzed using paired t-test and the probability value <0.05 was conside
... Show MoreThe compressive residual stresses generated by shot peening, is increased in a direct proportional way with shot peening time (SPT). For each metal, there is an optimum shot peening time (O.S.T) which gives the optimum fatigue life. This paper experimentally studied to optimize shot peening time of aluminium alloy 6061-T651 as well as using of and analysis of variance (ANOVA).
Two types of fatigue test specimens’ configuration were used, one without notch (smooth) and the other with a notch radius (1,25mm), each type was shot peened at different time. The (O.S.T) was experimentally estimated to be 8 minutes reaching the surface stresses at maximum peak of -184.94 MPa.
A response surface methodology (RSM) is presen
... Show MoreThe study aimed to effect of speed and die holes diameter in the machine on feed pellets quality. In this study was measured pellet direct measurement (%), pellet lengths (%), pellet durability (%) and pellet water absorption (%). Three die speeds 280, 300, and 320 rpm, three diameters of die holes in the machine 3, 4, and 5 mm, have been used. The results showed that increasing the pellet die speeds from 280 to 300 then to 320 rpm led to a significant decrease in direct measurement, pellet durability, and pellet water absorption was increased, whereas it did not significantly affect the pellet lengths. Increasing the die holes diameter from 3 to 4 then to 5 mm led to a significant de
Dry environment study forms an important part in the field of applies geomorphology for
the wide rang of its lands which form most of the world, homeland, and Iraqi lands specially,
and what these lands include of scientific cases which needs to be searched and investigated.
They include rocks, land shapes, water supplements, its ancient soil and its active diggings are
all signs of the environment changes and effects that these lands under take over time, with
continuous remains of its features of characteristics under geo morphological dry
circumstances which works to slow change average, when the geomorphologic fearers varies
in this environment and what it contain of important economical resource. As to participl
This research is about the resources and the way of al-Waqidi in his
researching of al-sira of the Prophet. And what happened in the first of Islam.
This research is about the documents which al-Waqidi had it. Some of it,
which he had visited, was the places, especially the periods which the events had took
place in. He was asking those whom were contemporary to the happenings, from the
sons of al-Sahaba and al-Tabi’een.
Also this research is lightening on the new studies that gave this historian a
good respect during his work, in which he could gave the reality about his authorship.
The research is trying to draw real way of al-Waqidi and what were reported by him,
especially the documents, and what he had s
Wisdom in the era before Islam is soo famous and so mature And Wisdom in the age of Islam {the holy quran and AI Hadeeth AI shareef }is dealt with by different meanings that agree with the contexts in which it occurs its contacs One of meanings is wisesaying that occuars in the Halal and Haram .As to the wisdom of the Amawy age ,it was some times absent since it was not dealt with by the great Poets of that age .In the Poetry of AL-FARAZDAK , Wisdom was little and it expressed religious and phsycological meanings because wisdom is amessage that has along –rang .