Improving of Photovoltaic Cell Performance by Cooling using Two different Types of Fins
(5)
Publication Date
Thu Feb 01 2024
Journal Name
Journal Of Engineering
Improving the Bearing Capacity of Clay Soil Using Plastic Bottle Waste
Carrying capacity
Plastic waste
Compression index (Cc)
Swelling index C(Cr)
With the increase in industry and industrial products, quantities of waste have increased worldwide, especially plastic waste, as plastic pollution is considered one of the wastes of the modern era that threatens the environment and living organisms. On this basis, a solution must be found to use this waste and recycle it safely so that it does not threaten the environment. Therefore, this research used plastic waste as an improvement material for clay soil. In this research, two types of tests were conducted, the first of which was a laboratory test, where the undrained shear strength (cohesion), compression index (Cc), and swelling index (Cr) of the improved and unimproved soils were calculated (plastic was added in pr
... Show More
(2)
(1)
Publication Date
Sat Feb 01 2020
Journal Name
Journal Of Global Pharma Technology,
Publication Date
Fri May 01 2020
Journal Name
Applied Thermal Engineering
Thermal performance of a flat-plate solar collector using aqueous colloidal dispersions of graphene nanoplatelets with different specific surface areas
Collector efficiency
Flat-plate solar collector
Water-based nanofluid
GNPs nanoparticles
Specific surface area
The effects of using aqueous nanofluids containing covalently functionalized graphene nanoplatelets with triethanolamine (TEA-GNPs) as novel working fluids on the thermal performance of a flat-plate solar collector (FPSC) have been investigated. Water-based nanofluids with weight concentrations of 0.025%, 0.05%, 0.075%, and 0.1% of TEA-GNPs with specific surface areas of 300, 500, and 750 m2/g were prepared. An experimental setup was designed and built and a simulation program using MATLAB was developed. Experimental tests were performed using inlet fluid temperatures of 30, 40, and 50 °C; flow rates of 0.6, 1.0, and 1.4 kg/min; and heat flux intensities of 600, 800, and 1000 W/m2. The FPSC’s efficiency increased as the flow rate and hea
... Show More
(43)
Publication Date
Thu Oct 01 2020
Journal Name
August
INFLUENCE OF SOME FACTOR ON SOMATIC EMBRYOS INDUCTION
AND GERMINATION OF DATE PALM BARHI C.V BY USING CELL
SUSPENSION CULTURE TECHNIQUE
INFLUENCE OF SOME FACTOR ON SOMATIC EMBRYOS INDUCTION AND GERMINATION OF DATE PALM BARHI C.V BY USING CELL SUSPENSION CULTURE TECHNIQUE
Publication Date
Fri Mar 20 2020
Journal Name
Plant Archives (09725210) 20 (2)
Publication Date
Fri Mar 27 2020
Journal Name
Plant Archives 20 (supplement 1), 1666-1670
Publication Date
Mon Apr 06 2020
Journal Name
August
INFLUENCE OF SOME FACTOR ON SOMATIC EMBRYOS INDUCTION
AND GERMINATION OF DATE PALM CV BARHI BY USING CELL
SUSPENSION CULTURE TECHNIQUE
This study was done to examine different concentrations of mercuric chloride (Hgcl2) for Explants sterilization and different
concentration of NAA) mg/L with 2iP for their effect on initiation primary callus and subsequent embryogenesis in Phoenix
dactyliferae cultivar Barhi. Leaf primordial and shoot tips were excised from 2-3 years old offshoot. The result showed that
contamination percentage decreased with an increase in concentration of Hgcl2 for two explants where in the control (0.0)%
gave highest value 75% and 62.5% of contamination for leaf primordial and shoot tip respectively while the addition (0.1)%
gave a significant decrease 37.5 and 0% for explants respectively. The Explants were inoculated onto Murashiege and Skoog
1962 (MS) medium supplemented with 2iP 3mg/L and containing 0
25
50 or 100 mg/L of NAA
the addition (50) mg/L of NAA
gave highest value 68.8% in percentage of callus initiation with significant difference from addition 0% gave lowest value
(18.8)%
as well Explants of shoot tip gave significant difference was 53.1% while leaf primordial gave 28.1%
Primary callus
was transferred to fresh MS medium containing (0
5
10 and 20) mg/L of NAA with 3mg/L 2iP
Results were recorded after 12
weeks. A highest value of embryonic callus induction percentage or fresh weight and dry weight 87.5% or 1.56g and 0.47g for
the character respectively for the treat 20 mg/L while control treatment 0.0 gave the lowest value 12.5% or 0.37g and 0.14g for
same character respectively. Inoculated 1g fresh biomass into a 250 ml Erlenmeyer flask containing 50 ml MS liquid medium
supplemented with NAA 20mg/L and agitated at 150 rpm by shaker to making suspension culture the measurements of
packed cell volume ( pcv) or fresh and dry weight taken weekly for 12 weeks
maximum values were reached in the eighth week
of PCV and fresh weight but the dry weight reached to highest value in seventh week
then the curve began to decline
gradually until it reached stability in the last two weeks. The cell suspension was Diluted to different initial cell density of 100
500
10000
50000 and 100000 cells /ml with hemocytometer. The initial cell number of (10000) cells gave significant different
of plating efficiency PE (11.6)% while (100) cells gave lowest value 1.8% of PE.
Publication Date
Sun Jan 01 2023
Journal Name
Plant Archives
INFLUENCE OF SOME FACTOR ON SOMATIC EMBRYOS INDUCTION AND GERMINATION OF DATE PALM CV BARHI BY USING CELL SUSPENSION CULTURE TECHNIQUEe
INFLUENCE OF SOME FACTOR ON SOMATIC EMBRYOS INDUCTION AND GERMINATION OF DATE PALM CV BARHI BY USING CELL SUSPENSION CULTURE TECHNIQUEe
Publication Date
Mon Jun 01 2020
Journal Name
Journal Of Engineering
Studying the Microstructure of Al-Ti Alloy Prepared by Powder Metallurgy using Three Different Percentages of Ti
Powder metallurgy
Microstructure
Intermetallic compound
Al-Ti alloy
The effect of different Ti additions on the microstructure of Al-Ti alloy prepared by powder metallurgy was investigated. A certain amount of Ti (10wt%, 15wt%, and 20wt%) were added to aluminium and the tests like microhardness, density, scanning electron microscope (SEM), optical microscope (OM) and X-Ray Diffraction (XRD) were conducted to determine the influence of different Ti additives on the Al-Ti alloy properties and microstructure. The results show that the grains of α-Al changed from large grains to roughly spherical and then to small rounded grains with increasing Ti content, the micro-hardness of the alloy increases with increasing Ti, and XRD results confirm the formation of TiAl3 intermetallic co
... Show More
(3)
Publication Date
Mon Sep 01 2014
Journal Name
Al-khwarizmi Engineering Journal
Using TermoDeck System for Pre-Cooling/ Heating to Control the Building Inside Conditions
In this paper, experimental study has been done for temperature distribution in space conditioned with Ventilation Hollow Core Slab (TermoDeck) system. The experiments were carried out on a model room with dimensions of (1m 1.2m 1m) that was built according to a suitable scale factor of (1/4). The temperature distributions was measured by 59 thermocouples fixed in several locations in the test room. Two cases were considered in this work, the first one during unoccupied period at night time (without external load) and the other at day period with external load of 800W/m2 according to solar heat gain calculations during summer season in Iraq. All results confirm the use of TermoDeck system for ventilation and cooling/heat
... Show More