Complexes of Au (III), Pd (II), Pt (IV ) and Rh(III) with S–propynyle-2- thiobenzimidazole (BENZA) have been prepared and characterized by IR and UV- Visible spectral methods in addition to magnetic and conductivity measurements and micro–elemental analysis (CHN).The probable structures of the new complexes have been suggested.

The standard formulation of Wave Intensity Analysis (WIA) assumes that the flow velocity (U) in the conduit is <;<; the velocity of propagation of waves (c) in the system, and Mach number, M=U/c, is negligible. However, in the large conduit arteries, U is relatively high due to ventricular contraction and c is relatively low due to the large compliance; thus M is > 0, and may not be ignored. Therefore, the aim of this study is to identify experimentally the relationship between M and the reflection coefficient in vitro. Combinations of flexible tubes, of 2 m in length with isotropic and uniform circular cross sectional area along their longitudinal axes, were used to present mother and daughter tubes to produce a range of reflection coeffic

A cantilever beam is made from composite material which is consist of (matrix: polyester) and (particles: Silicon-Carbide) with different volume fraction of particles. A force is applied at the free end of beam with different values. The experimental maximum deflection of beam which occurs at the point of the applied load is recorded. The deflection and slope of beam are analyzed by using FEM modeling. MATLAB paltform is built to assemble the equations, vector and matrix of FEM and solving the unknown variables (deflection and slope) at each node. Also ANSYS platform is used to modeling beam in finite element and solve the problem. The numerical methods are used to compare the results with the theoretical and experimental data. A good ag

     A new Schiff base ligand was prepared via a condensation reaction. The synthesis involved combining N-(4-aminophenylsulfonyl) benzamide (also known as sulfabenzamide) with indoline-2,3-dione. To facilitate the reaction, three drops of glacial acetic acid were added. This process yielded the ligand N-(4-(2-oxoindoline-3-ylideneamino) phenylsulfonyl) benzamide, designated as (L). Mixed ligand complexes were prepared in a molar ratio (1:1:1) (M:1,10-phen, L) at concentrations of 10-4M by interacting L and 1,10-phenanthroline, with the following metal ions (Cr+3, Mn+2, Zn+2, Pd+2, Cd+2, Pt+4). These complexes exhibited different geometric shapes, including (octahedral for both Cr+3, Mn+2, Pt+4, tetrahedral for Zn+2 and Cd+2, an

The present study is to investigate the possibility of using wastes in the form of scrap iron (ZVI) and/ or aluminum ZVAI for the detention and immobilization of the chromium ions in simulated wastewater. Different batch equilibrium parameters such as contact time (0-250) min, sorbent dose (2-8 g ZVI/100 mL and 0.2-1 g ZVAI/100 mL), initial pH (3-6), initial pollutant concentration of 50 mg/L, and speed of agitation (0-250) rpm were investigated. Maximum contaminant removal efficiency corresponding to (96 %) at 250 min contact time, 1g ZVAI/ 6g ZVI sorbent mass ratio, pH 5.5, pollutant concentration of 50 mg/L initially, and 250 rpm agitation speed were obtained.

The best isotherm model for the batch single Cr(III) uptake by ZVI

Finite element modeling of transient temperature distribution is used to understand physical phenomena occurring during the dwell (penetration) phase and moving of welding tool in friction stir welding (FSW) of 5mm plate made of 7020-T53 aluminum alloy at 1400rpm and 40mm/min.
Thermocouples are used in locations near to the pin and under shoulder surface to study the welding tool penetration in the workpiece in advance and retreate sides along welding line in three positions (penetrate (start welding) , mid, pullout (end welding)).
Numerical results of ANSYS 12.0 package are compared to experimental data including axial load measurements at different tool rotational speeds (710rpm.900rpm.1120rpm and 1400rpm) Based on the experiment

In the present study, advanced oxidation process / heterogeneous photocatalytic process (UV/TiO₂/Fenton) system was investigated to the treatment of oily wastewater. The present study was conducted to evaluate the effect of hydrogen peroxide concentration H₂O₂, initial amount of the iron catalyst Fe⁺², pH, temperature, amount of TiO₂ and the concentration of oil in the wastewater.  The removal efficiency for the system UV/TiO₂/Fenton at optimal conditions and dosage (H₂O₂ = 400mg/L, Fe⁺² = 40mg/L, pH=5, temperature =30^oC, TiO₂=75mg/L) for 1000mg/L load was found to be 77%.

Aluminum foil cover around the re