Titanium dioxide (TiO2) thin films were prepared under different pressures with values (15, 30, 60 and 120) Pa using the DC reactive magnetron homemade system with mixed gases of argon and oxygen in ratio (50:50). The result of X-ray diffraction patterns discovered that the structure of the deposited films was polycrystalline, including the phase of anatase. All the appeared peaks were matched to the planes (101), (004), (105), and (211) of diffracted states. Both the intensities and the number of the appeared peaks are declined according to the increased pressure, and the plane of (101) is be considered the preferential grown plane, it is taking a maximum texture factor. Both the lattice constant and the atomic inter-planer spacing take the highest standard values of the divergence. The transmittance intensity and the Urbach energy were observed to decline with decreasing the total pressure. The thickness of the prepared films was approximately 200 nm. Through the results, it was found that the highest value of the energy gap was at a pressure of 120 Pa.
Introduction: Although soap industry is known from hundreds of years, the development accompanied with this industry was little. The development implied the mechanical equipment and the additive materials necessary to produce soap with the best specifications of shape, physical and chemical properties. Objectives: This research studies the use of vacuum reactive distillation VRD technique for soap production. Methods: Olein and Palmitin in the ratio of 3 to 1 were mixed in a flask with NaOH solution in stoichiometric amount under different vacuum pressures from -0.35 to -0.5 bar. Total conversion was reached by using the VRD technique. The soap produced by the VRD method was compared with soap prepared by the reaction - only method which
... Show MoreBackground: Dental implant surface technologies have been evolving rapidly to enhance a more rapid bone formation on their surface and improve implant therapy.Implant threads should be designed to increase surface contact areathat induced better stability. In addition, implant surface coating with Flaxseed was used to enhance bone formation at the bone-implant interface. Materials and methods: Ninety-six commercially pure titanium (CpTi) screws were implanted in rabbits' tibiae and divided into three groups as dual-threaded group, flaxseed-coated group and control group. All groups were evaluated mechanically, histologically and radiographically after each healing periods (2, 4, 6 and 8) weeks and the resulting data were statistically analy
... Show MoreThis research concluded that after what has been presented an analysis of the topics that the process of measuring the level of development and then the development gap is the need to assess the results to set policy and to formulate plans and goals, and to see the development priorities of the place or a particular sector. The purely economic development led to negative effects on the spatial scale and the most important of these effects arise multidimensional social and urban development gaps as well as the economic dimension. So it must exceed the concept of economic framework, to include all dimensions of development spatially and sectorally to provide correct and clear base for planners and development policies and strategies for de
... Show MoreInfertility represents a growing health problem in Mosul city and worldwide. Infertility defined as a failure to induce pregnancy after unprotected sexual intercourse for more than 12 months. Infertility in male is a multifactorial complex pathology that leads to different types of problems. This work try to explore the correlation between glycosylation gap and seminal fructosamine and another parameter in the young male patient in Mosul city. The study included 50 subjects with age range 19-29 year with BMI 18-26. The infertility group include 25 patients newly diagnosed with infertility before starting any treatment; have no infection and no structural abnormality. The control group included 25 healthy subjects. HbA1c, fructosamine, Se
... Show More
This paper describes DC motor speed control based on optimal Linear Quadratic Regulator (LQR) technique. Controller's objective is to maintain the speed of rotation of the motor shaft with a particular step response.The controller is modeled in MATLAB environment, the simulation results show that the proposed controller gives better performance and less settling time when compared with the traditional PID controller.
This study aims to identify the level of application of blue ocean leadership activities in public organizations and to build a conceptual and cognitive framework around this concept. The study adopted a descriptive-analytical approach, and the research sample consisted of (95) individuals from the senior management working at the center of the Iraqi Ministry of Communications (director general, department manager, section head). The data analysis technique used is structural equation modeling (SEM) and the Statistical Package for the Social Sciences (SPSS). The results indicate that the senior management in the Ministry of Communications is working to adopt the blue ocean leadership style through its activities, but not to the leve
... Show MoreIn this research we prepared CdS thin films by Spray pyrolysis method on a glass substrates and we study its structural , optical , electrical properties .The result of (X-Ray ) diffraction showed that all thin films have a polycrystalline structure , The relation of the transmission as a function of wavelength for the CdS films had been studied , The investigated of direct energy gap of the CdS its value is (2.83 eV). In Hall effect measurement of the CdS we find the charge carriers is p – type and Hall coefficient 1157.33(cm3/c) ,Hall mobility 6.77(cm2/v.s)