The present study aimed to determine the genetic divergence of seven maize genotypes (Al-Maha, Sumer, Al-Fajr, Baghdad, 5018, 4 × 1 single hybrid, and 4 × 2 single hybrid) under two varied levels of nitrogen fertilization (92 and 276 kg N ha-1). The experiment occurred in 2022 in a randomized complete block design (RCBD) with a split-plot arrangement and three replications at the College of Agricultural Engineering Sciences, University of Baghdad, Iraq. The nitrogen fertilization levels served as main plots, with the maize genotypes allocated as the subplots. The results revealed that genetic variance was higher than the environmental variance for most traits, and the coefficient of phenotypic variation was close to the genetic variation coefficient under the two levels of nitrogen fertilization. Heritability (broad sense) at the 92 kg N ha-1 (N1 level) was the highest for traits. i.e., ear height, grains per row, grains per ear, individual plant yield, yield per unit area, days to 50% male flowering, leaf area, ear length, rows per ear, and 100-grain weight, with values of 92.556%, 90.760%, 90.123%, 95.007%, 95.007%, 88.976%, 89.974%, 88.748%, 85.521%, and 89.690%, respectively. For the N level of 276 kg ha-1 (N2 level), the heritability in a broad sense was high for the traits, viz., days to 50% male flowering (91.546%), plant height (96.150%), ear height (91.038%), ear length (92.454%), individual plant yield (98.108%), yield in the unit area (98.108%), and plant dry weight (85.488%). The cluster analysis divided the maize genotypes into four and five cluster groups under the nitrogen fertilization level of 92 and 276 kg N ha-1, respectively. These different groups of maize genotypes could be due to the genetic divergence among the genotypes resulting from their varied genetic makeup and origin.
197 vaginal swabs were collected from women of different ages. (60) Isolates of Candida albicans (30.4%) were obtained, and the other species of Candida represent (18.27%). Bacterial infections showed (41.11%), and infection with Trichomonas vaginalis was (2.03%). Ten isolates of C. albicans were chosen randomly for farther study which include two virulence factors tendency of adhesion wich showed a percentage of (52%) to(32%) , and the ability to produce phospholipaze enzyme and it’s activity which showed (50%) of the isolates have the ability to produce the enzyme in different degrees .
The economical design of plate loaded by pressure can be obtained by using stiffeners instead of increasing the thickness of plate. The main subject of this work is to obtain the effect of stiffener height on the maximum stress in the plate subjected to pressure load. Different plate-stiffener sets are selected to find the effects of stiffener thickness, plate dimensions and pressure, on the optimum stiffener height. The models under consideration are square plates clamped rigidly from four edges. Finite Element method is used to analyze 160 different models by using the Finite Element software package ANSYS version 11. Another analysis method based on maximum stress equation is used to analyze 30 models. The graphical comparison of results
... Show MoreThis study has been undertaken to postulate the mechanism of impact test at low velocities. Thin-walled tubes of 100Cr6 were deformed under axial compression. In the present work there are seven velocities (4.429,4.652,5.240,5.600,5.942,6.264, 6.569) m\sec were applied to show how they effect the load, change in length, also the kinetic energy. However, the comparison between the obtained results and the other studies (Alexandar[3] , Abramowicz[4], Ayad[5]) was made the present work and Ayad data show good agreement. Load, change in length, kinetic energy were determined to understand the impact test.
In this paper, the behavior of spliced steel girders under static loading is investigated. A group of seven steel I-girders were tested experimentally. Two concentrated loads were applied to each specimen at third points and the load was increased incrementally up to the yield of the specimen. Two types of splices were considered; the bearing type and the friction-grip type splices. For comparison, an analytical study was made for the tested girders in which the finite element analysis program (Abaqus) was used for analysis. It was found that the maximum test load for spliced girders with bearing type splices was in the range of (34%) to (67%) of the maximum test load for the reference girder. For girders spliced by using friction-grip t
... Show MoreOne of the Iraqi geotechnical problems is the presence of gypseous soils covering about (27-36) percentage of Iraq soils containing gypsum between (10-70) ratios. The main reason for soil problematic is the gypsum dissolution when these soils are inundated. However, the soluble gypsum can be leached out of the soil particles, so these problems can be led to cracking, tilting, and collapsing the related soil structure and changing the soil properties. The aim of this work is to investigate the performance of under-reamed piles as a new, improved method to reduce the moisture sensitive and the primary triggering mechanism for the volume reduction of collapsible soil, which is considered as a non-elastic deformation; this was done by c
... Show MoreThis research aims to know the reality of succession planning in the researched organization and how it occupies the important jobs in the organization and its readiness for sudden and urgent events that lead to the vacancy of these jobs, and the importance of this research is that it is one of the rare Arab and Iraqi studies and research in this field, as it is one of the first researches It deals with the reality of succession planning in light of the retirement law No. (26) of 2019, and the research problem was the absence of consecutive planning programs and the weak preparation of suitable candidates to face sudden and urgent conditions as replacements for current leaders who occupy the leading and key positions in the depar
... Show More