Introduction: An aneurysmal bone cyst are enigmatic lesion of unknown cause and presentation and are difficult to distinguish from other lesions, it is a benign, but expansible tumor like lesion that generally occurs in the long bones. An aneurysmal bone cyst arising from the flat bone like clavicle is rare . Case presentation: We report a 12-year-old girl child with an aneurysmal bone cyst of the lateral third of left clavicle treated with enblock resection. The pathologic findings confirmed the diagnosis of aneurysmal bone cyst. The patient has been followed up for one year with no evidence of recurrence . Conclusion: En bloc resection can be curative and provide good results for this rare type of clavicle tumour.

The present experimental work is conducted to examine the influence of adding Alumina (Al₂O₃) nanoparticles and Titanium oxide (TiO₂) nanoparticles each alone to diesel fuel on the characteristic of the emissions. The size of both Alumina and Titanium oxide nanoparticles which have been added to diesel fuel to obtain nano-fuel is about 20 nm and 25 nm respectively. Three doses of (Al₂O₃) and (TiO₂) were prepared (25, 50, and 100) ppm. The nanoparticles mixed with gas oil fuel by mechanical homogenous (manual electrical mixer) and ultrasonic processor. The study reveals that the adding of Aluminum oxide (Al₂O₃) and Titanium oxide (TiO₂) to g

Background: Concha bullosa is an anatomical variation which defined by pneumatizaton of middle turbinate that occurred with an incidence of (5 to 25%) in the normal population.It has the potential to cause crowding and obstruction of the middle meatus and nasal cavity. There are many surgical techniques which utilized for its management. Study goal: Is to compare the formation of adhesion between endoscopic partial lateral middle turbinectomy and middle turbinate trimming in cases of concha bullosa. Patients and methods: A prospectivecomparative clinical trial was performed in the ENT department at Al-Shahid Ghazi AL Hariri Hospital in Medical City over the period from September 2016 to August 2017. Fifty nine (59) patients {24 males

The aim of this research is to investigation the optimization of the machining parameters (spindle speed, feed rate, depth of cut, diameter of cutter and number of flutes of cutter) of surface roughness for free-form surface of composite material (Aluminum 6061 reinforced boron carbide) by using HSS uncoated flat end mill cutters which are rare use of the free-form surface. Side milling (profile) is the method used in this study by CNC vertical milling machine. The purpose of using ANFIS to obtain the better prediction of surface roughness values and decreased of the error prediction value and get optimum machining parameters by using Taguchi method for the best surface roughness at spindle speed 4500 r.p.m, 920mm/rev feed rate, 0.6mm de

The construction of embankment for roadway interchange system at urban area is restricted due to the large geometry requirements, since the value of land required for such construction is high, and the area available is limited as compared to rural area. One of the optimum solutions to such problem is the earth reinforcement technique which requires a limited area for embankment construction. Gypseous soil from Al-Anbar governorate area was obtained and subjected to various physical and chemical analysis to determine it is properties. A laboratory model box of 50x50x25 cm was used as a representative embankment; soil has been compacted in five layers at maximum dry density (modified compaction) and an aluminum reinforcement strips were i

Buckling analysis of composite laminates for critical thermal (uniform and linear) and mechanical loads is reported here. The objective of this work is to carry out theoretical investigation of buckling analysis of composite plates under thermomechanical loads, and experimental investigation under mechanical loads. The analytical investigation involved certain mathematical preliminaries, a study of equations of orthotropic elasticity for classical laminated plate theory (CLPT), higher order shear deformation plate theory (HSDT) , and numerical analysis (Finite element method), then the equation of motion are derived and solved using Navier method and Levy method for symmetric and anti-symmetric cross-ply and angle-ply laminated plates t