Refractories are mineral and chemical-, based, materials with excellent heat resistance, making them ideal for use in the construction of ovens, furnace walls industries. According to this our research is concerned to study the effect of addition of (4% CaO) and (5% graphite) on the silica brick properties. Different amounts of CaO and Graphite were included in the white sand (raw ingredients) of silica bricks as a binder to prepare the composition then the composition were sintered using Different sintering temperatures ranging from (1000–1400)𝛐C under static air. Density, thermal conductivity, porosity, and water absorption Compression there was power tested after sintering. XRD analysis was used to identify raw materials’ physical, chemical, and mechanical qualities, as well as their mineralogical composition. Addition of Graphite to the firebrick mixture increased the challenges of getting good densification out of firebrick specimens with enhancement of the compressive, strength, bulk density especially at low firing temperatures since it increases formation of glassy phase as compared with 4%CaO, Addition of 4% CaO to silica brick the density of firebrick decreased, and the porosity and water absorption increased. Thermal conductivity of firebrick is decreased for 5% Graphite in comparison with 4% CaO to produce refractory silica brick with high quality of heat resistance, making them ideal for use in the construction of ovens, furnace walls industries.
BixSb2-xTe3 alloys with different ratios of Bi (x=0, 0.1, 0.3, 0.5, and 2) have been prepared, Thin films of these alloys were prepared using thermal evaporation method under vacuum of 10-5 Torr on glass substrates at room temperature with different deposition rate (0.16, 0.5, 0.83) nm/sec for thickness (100, 300, 500) respectively. The X–ray diffraction measurements for BixSb2-xTe3 bulk and thin films indicate the polycrystalline structure with a strong intensity of peak of plane (015) preferred orientation with additional peaks, (0015) and (1010 ) reflections planes, which is meaning that all films present a very good texture along the (015) plane axis at different intensities for each thin film for different thickness. AFM measureme
... Show MoreMoisture damage is a primary mode of distress occurring in hot mix asphalt (HMA) pavements in Iraq. Because of the loss of bond, or stripping, caused by the presence of moisture between the asphalt and aggregate, which is a problem in some areas and can be severe in some cases, it is requires to evaluate the design asphalt mixture to moisture susceptibility. Many factors such as aggregate characteristics, asphalt characteristics, environment, traffic, construction practices and drainage can contribute to stripping. Asphalt concrete mixes were prepared at their optimum asphalt content by superpave system and then tested to evaluate their engineering properties, which include tensile strength, resilient modulus, and perman
... Show More
priorities of materials research due to their promising properties, especially in the field of thermoelectricity. The efficiency or performance of thermoelectric devices is expressed in terms of the thermoelectric figure-of-merit (ZT) – a standard indicator of a material’s thermoelectric properties for use in cooling systems. The evaluation of ZT is principally determined by the thermoelectric characteristics of the nanomaterials. In this paper, a set of investigative computations was performed to study the thermoelectric properties of monolayer TMDCs according to the semiclassical treatment of the Boltzmann transport equation. It was confirmed that the thermoelectric properties of 2D materials can be greatly improved compared with thei
... Show MoreThis research of using Feldspar in the production self compacting concrete (SCC) ( 5,10,15 )% as partial replacement by weight of cement .In this research some of fresh properties of SCC ( slump flow used V-funnel test and filling ability used ( U- box test ) for concrete mixes and also some of the harden properties of SCC ( compressive and flexural tests ). The research results showed that negative effect of Feldspar on the fresh properties of self compacting concrete but the positive effect of Feldspar on the harden properties of self compacting concrete .
Gypsum is one of the important construction materials in Iraq in plastering surfaces and gypsum board , the ability of gypsum to give a comfortable an aesthetic ambiance as a construction material increase the need of gypsum , The particle size , total surface area and particle size distribution were factors affecting plaster properties used for construction properties . In this study gypsum paste was used with different mixing ratios of particle size and studied the physical properties of these types of pastes named (standard consistency ,setting time ,density) and compressive strength . The results showed that the water to gypsum ratio increased with increasing the fineness of the gypsum to (0.75%) and the setting time to the maxi
... Show MoreThe ground state proton, neutron and matter densities andcorresponding root mean square radii of unstable proton-rich 17Neand 27P exotic nuclei are studied via the framework of the twofrequencyshell model. The single particle harmonic oscillator wavefunctions are used in this model with two different oscillator sizeparameters core b and halo , b the former for the core (inner) orbitswhereas the latter for the halo (outer) orbits. Shell model calculationsfor core nucleons and for outer (halo) nucleons in exotic nuclei areperformed individually via the computer code OXBASH. Halostructure of 17Ne and 27P nuclei is confirmed. It is found that thestructure of 17Ne and 27P nuclei have 25 / 2 (1d ) and 1/ 2 2s -dominantconfigurations, resp
... Show MoreKHalaf Alhmar and what we get from his poem
134 samples of plants and animals wastes were taken from three different regions outside Baghdad and three different regions in Baghdad. 24 cellulolytic isolates fungi AO, C1, TH1, AN1, R1, TV, PG, AF, B1, L1, AP, TH, AP1, AN3, AO2, A, A1, C, F, AO1, C2, F1, CL and AP2 independent were chosen out of 48 selected fungi. The best optimal conditions for growth were 30ºC and pH 7. The isolates were identified and screened according to the colony diameter, biomass and density of spores in addition of capability to produce the hydrolytic enzymes for cellulose.