BACKGROUND: Polycystic ovary syndrome(PCOS) is one of the most common endocrine disorder affecting women in reproductive age. No single etiologic factor fully accounts for the spectrum of abnormalities in the polycystic ovary syndrome. Different changes in hormonal, metabolism and the inflammatory markers as squealy of PCOS with adverse effect on the women life. OBJECTIVE: To study the relationship between polycystic ovary syndrome and levels of C-reactive protein, human interleukin and hormonal and metabolic alteration in women with PCOS PATIENTS AND METHODS: Thirty women with Polycystic Ovary syndrome (PCOS) and other thirty women without PCOS were included. Venous blood samples were taken in early follicular phase of menstrual cycle [day 2-6] for luteinizing hormone (LH), follicle-stimulating hormone (FSH), and testosterone. Serum level of Human Interleukin 1B (IL-1B) was quantitatively determined. Blood samples were also tested for detection of CRP (C-reactive protein, in addition to levels of cholesterol, triglycerides. RESULTS: The mean cholesterol level was significantly higher in PCOS group rather than controls; (188.3 ± 7.2) vs. (168.7 ± 6.1) respectively. Mean LH level was higher in PCOS women than control (13.3 ± 2.4 IU/L) vs. (5.85 ± 1.47) IU/L, while in contrary mean FSH level was lower in PCOS cases. The mean serum testosterone in PCOS group was significantly higher than in controls, with no significant difference regarding IL-1B, but again it was significant in cases of CRP. CONCLUSION: PCOS was associated with higher levels of cholesterol, LH, and serum testosterone with lower levels of FSH. Positive C-Reactive Protein was more frequent in PCOS cases. Still serum level of Human Interleukin 1B (IL-1B) was not significantly affected by PCOS.
ENGLISH
(1)
(1)
(1)
Furfural is a toxic aromatic aldehyde that can cause a severe environmental problem especially the wastewater drown from petroleum refinery units. In the present work, a useless by-product from local furniture manufacturing industry; sawdust was used as raw material for the preparation of activated carbon which is chemically activated with phosphoric acid. The effect of adsorption variables which include initial pH of solution (2-9), agitation speed (50-250) rpm, agitation time (15-120) min, initial concentration of furfural (50-250) ppm, and amount of adsorbent material (0.5-2.5) g for the three adsorbents used (prepared activated carbon, commercial activated carbon and raw sawdust) were investigated in a batch process
... Show More
(3)
The main aim of this paper is studied the punching shear and behavior of reinforced concrete slabs exposed to fires, the possibility of punching shear failure occurred as a result of the fires and their inability to withstand the loads. Simulation by finite element analysis is made to predict the type of failure, distribution temperature through the thickness of the slabs, deformation and punching strength. Nonlinear finite element transient thermal-structural analysis at fire conditions are analyzed by ANSYS package. The validity of the modeling is performed for the mechanical and thermal properties of materials from earlier works from literature to decrea
... Show More
(5)
Fabrication of porous clay refractory insulating specimens from Iraqi kaolin with different percentage of Expanded Polystyrene (EPS) waste crumbs additions were investigated. After mixing and forming by hand molding, the specimens was dried and fired at 1300 oC. The structural, physical, mechanical and thermal properties of the refractory insulating products were measured. Maximum addition of EPS (1.25 wt%) lead to reduce the linear shrinkage to less than 1.7% and increased apparent porosity up to 50 %. As well as, the density, Modulus of rupture and thermal conductivity were reduced to 1.39 g/cm3, 4.1 MPa and 0.21 W/m.K, respectively. The final outcome, addition of EPS showed good results in the formation of pores without distorting the
... Show More
(5)
A Longitudinal opening is used to construct hollow core beam is a cast in site or precast or pre stressed concrete member with continuous voids provided to reduce weight, cost and, as a side benefit, to use for concealed electrical or mechanical runs. Primarily is used as floor beams or roof deck systems. This study investigate the behavior of six beams (solid or with opening) of dimension (length 1000 x height 180 x width120mm) simply support under partial uniformly distributed load, four of these beam contain long opening of varied section (40x40mm) or (80x40mm). The effect of vertical steel reinforcing, opening size and orientations are investigated to evaluate the response of beams. The experimental behavior based on load-deflection
... Show More
(18)
This study introduced the effect of using magnetic abrasive finishing method (MAF) for finishing flat surfaces. The results of experiment allow considering the MAF method as a perspective for finishing flat surfaces, forming optimum physical mechanical properties of surfaces layer, removing the defective layers and decreasing the height of micro irregularities. Study the characteristics which permit judgment parameters of surface quality after MAF method then comparative with grinding
Colloidal crystals (opals) made of close-packed polymethylmethacrylate (PMMA) were fabricated and grown by Template-Directed methods to obtain porous materials with well-ordered periodicity and interconnected pore systems to manufacture photonic crystals. Opals were made from aqueous suspensions of monodisperse PMMA spheres with diameters between 280 and 415 nm. SEM confirmed the PMMA spheres crystallized uniformly in a face-centered cubic (FCC) array. Optical properties of synthesized pores PMMA were characterized by UV–Visible spectroscopy. It shows that the colloidal crystals possess pseudo photonic band gaps in the visible region. A combination of Bragg’s law of diffraction and Snell’s law of refraction were used to calculate t
... Show More
Reliability is an essential measure and important component of all power system planning and operation procedures. It is one of the key design factors when designing complex, critical and expensive systems. This paper presents a fuzzy logic approach for reliability improvement planning purposes. Evaluating the reliability of the complex and large planned Iraqi super grid ;as Al- Khairat generating station with its tie set is intended to be compact to that grid; and determination of the given reliability improvement project are the major goals of the paper. Results show that the Iraqi super grid reliability is improved by 9.64%. In the proposed technique, fuzzy set theory is used to include imprecise indices of different components in normal
... Show More