The aim of the research is to identify the role of university education management in achieving sustainable environmental development.

• The problem of infertility considers one of the chronic problem a which faced the
  individual & families equally . This problem causes a negative effects in psychological ,
  social and development fields. The infertility contributes in weakening the human
  development, when the human development has become as a centre point which centered
  about individual preparing , rehabilitation, training and knowledge toreach to the required
  excellence.
  We think that , the infertility destroys the socially development; therefore the socially and
  scientific institutions are working hard to find successful solution to resolve the problem
  infertility through sophisticated and scientific methods. This problem

The problems of urban historic centers are considered some of the subjects which are widely dealt with in urban studies since the middle of the 20th century. literature of urban development have raised it , beside the fact that large number of urban development projects of the historical centers in many cities of the world ,and emerged from the application of these new problems projects added their original urban problems , because these projects have dealt with the physical structures with the neglect of the social and economic sides, which are the base in sustainable development nResearch problem was elaborated as : The unclearly of knowledge of the potentials of the sustainable development in solving the urban problems of historic cen

A Stereomicroscopic Evaluation of Four Endodontic Sealers Penetration into Artificial Lateral Canals Using Gutta-Percha Single Cone Obturation Technique, Omar Jihad Banawi*, Raghad

Strategic Cost Management Tools Under Technological Development and Change in Customer Tastes Critical Studies

6. coli K12 and B. subtilis 168 were investigated for their cadmium and mercury tolerance abilities. They were developed by UV mutagenesis technique to increase their tolerances either to cadmium or mercury, and their names then were designated depend on the name and concentration of metals. E. coli K12 Cd3^R exhibited bioremediation amount of 6.5 mg Cd/g dry biomass cell. At the same time, its wild-type (E. coli K12 Cd3) was able to remove 5.2 mg Cd/g dry biomass cell in treatment of 17 mg Cd /L within 72 hours of incubation at 37 °C (pH=7) in vitro assays. The results show that E.coli K12 Hg 20 was able to remove 0.050 µg Hg/g dry biomass cell

Every researcher must say that the world in continually progress toward the best and that
the Arab and Islamic civilization had produced much of systems and virtuous educational
practices which raised from Islamic heritage. This nation was not isolated from external
world, but it was made a clear active for promote the banner of other nations which entered
under her influence to promote Islamic banner and Muslims. Consequently also Muslims are
affected and influenced, this resulted a clear impact in the civilization and educational
ideology especially in the contemporary teaching methods.

This research was conducted to determine content levels of heavy metal pollution. Samples taken from Ishaqi River bank and adjacent agricultural soils area, in ten sites, distributed along 48 km of the Ishaqi River, north Baghdad. The evaluated metals were Zinc, Copper, Manganese, Iron, Cobalt, Nickel, Chromium, Cadmium, Vanadium and Lead. PH and Electric Conductivity (EC) were measured to evaluate the acidity and (EC). Results showed that most site were contaminated with metals evaluated. Among these metals, Zn, Mn, Fe and Ni were consistently higher in all the samples (both river bank and adjacent soil) followed by PB, CU, V, Cd, Co and Cr. The level concentrations of river bank were almost higher than that of adjacent soil. As will be re

Tungsten inert gas arc welding–based shaped metal deposition is a novel additive manufacturing technology which can be used for fabricating solid dense parts by melting a cold wire on a substrate in a layer-by-layer manner via continuous DC arc heat. The shaped metal deposition method would be an alternative way to traditional manufacturing methods, especially for complex featured and large-scale solid parts manufacturing, and it is particularly used for aerospace structural components, manufacturing, and repairing of die/molds and middle-sized dense parts. This article presents the designing, constructing, and controlling of an additive manufacturing system using tungsten inert gas plus wire–based shaped metal deposition metho