By optimizing the efficiency of a modular simulation model of the PV module structure by genetic algorithm, under several weather conditions, as a portion of recognizing the ideal plan of a Near Zero Energy Household (NZEH), an ideal life cycle cost can be performed. The optimum design from combinations of NZEH-variable designs, are construction positioning, window-to-wall proportion, and glazing categories, which will help maximize the energy created by photovoltaic panels. Comprehensive simulation technique and modeling are utilized in the solar module I-V and for P-V output power. Both of them are constructed on the famous five-parameter model.  In addition, the efficiency of the PV panel is established by the genetic algorithm

Nowadays, the mobile communication networks have become a consistent part of our everyday life by transforming huge amount of data through communicating devices, that leads to new challenges. According to the Cisco Networking Index, more than 29.3 billion networked devices will be connected to the network during the year 2023. It is obvious that the existing infrastructures in current networks will not be able to support all the generated data due to the bandwidth limits, processing and transmission overhead. To cope with these issues, future mobile communication networks must achieve high requirements to reduce the amount of transferred data, decrease latency and computation costs. One of the essential challenging tasks in this subject

Tensile strength is a critical property of Hot Mix Asphalt (HMA) pavements and is closely related to distresses such as fatigue cracking. This study aims to evaluate methods for assessing fatigue cracking in Asphalt Concrete (AC) mixes. In order to achieve optimum density at different binder contents, the mixes were compressed using a gyratory compactor. Tensile strength was assessed using the Indirect Tensile (IDT) and Semi-Circular Bend (SCB) tests. The results showed that the tensile strength measured by the SCB test was consistently higher than that measured by the IDT test at 25 °C. In addition, the SCB test showed a stronger correlation between increasing binder content and tensile strength. For binder contents ranging from 4

A winglet is devices attached at the wing tips, used to improve aircraft wing efficiency by reduction influence wing tips vortices and induct drag, increasing lift force at the wing tips and effective aspect ratio without adding greatly to the structural stress and weight in the wing structure. This paper is presented three-dimensional numerical analysis to proposed modification swept back wing by adding Raked winglets devices at the main wing tips belong the two seat trainer aircraft type Aermacchi Siai S211 by using Fluent ANSYS 13 software. CFD numerical analysis process was performed at the same flight boundary conditions indifferent wing angle of attacks with constant air flow velocity V∞ =50 (m/sec), ambient pressure Po=101325 (P

The dynamic response of foundation rest on collapsible soil in dry and soaked states is studied through wide experimental programmed. Gypseous soil from Tikrit governorate area was obtained and subjected to various physical and chemical analysis to determine its properties. Steel rectangular footing (400x200x20) mm is manufactured. The machine is fitted to the footing, then the model machine foundation is placed centrally over the prepared soil layer in steel container (1200x 1000x1000)mm with proper care to maintain the center of gravity of whole system lie in the same vertical line with container.Then, the footing is subjected to vertical harmonic loading using a rotating mass type mechanical oscillator to simulate different dynamic lo

The continuous increase in population has led to the development of underground structures like tunnels to be of great importance due to several reasons. One of these reasons is that tunnels do not affect the living activities on the surface, nor they interfere with the existing traffic network. More importantly, they have a less environmental impact than conventional highways and railways. This paper focuses on using numerical analysis of circular tunnels in terms of their behavior during construction and the deformations that may occur due to overburden and seismic loads imposed on them. In this study, the input data are taken from an existing Cairo metro case study; results were found for the lateral and vertical displacements, the Peak

A free convective heat transfer from the inside surface of a uniformly heated vertical circular tube has been experimentally investigated under a constant wall heat flux boundary condition for laminar air flow in the ranges of Ra_L from 6.910⁸ to 510⁹. The effect of the different sections (restrictions) lengths placed at the exit of the heated tube on the surface temperature distribution, the local and average heat transfer coefficients were examined. The experimental apparatus consists of aluminum circular tube with 900 mm length and 30 mm inside diameter (L/D=30). The exit sections (restrictions) were included circular tubes having the same inside diameter as the heated tube but with different lengths of

Polymeric hollow fiber membrane is produced by a physical process called wet or dry/wet phase inversion; a technique includes many steps and depends on different factors (starting from selecting materials, end with post-treatment of hollow fiber membrane locally manufactured). This review highlights the most significant factors that affect and control the characterization and structure of ultrafiltration hollow fiber membranes used in different applications.    

   Three different types of polymers (polysulfone PSF, polyethersulfone PES or polyvinyl chloride PVC) were considered to study morphology change and structure of hollow fiber membranes in this review. These hollow fiber membranes were manufactured with different pro

The current study has beenconduced to evaluate the effect of extracted crude terpens at the concentrations of 6,8% of seeds of Eucalyptuscamaldulensison the 4th larval instar oftheCallosobruchusmaculates and the percentage of the cowpea seed germination.The Results showed that the terpens extract of the concentration of 8% increases the mortality rate of the fourth larval instar and it reach to 63.3%, and then decrease of to 26.6,20% at concentration of 6%and forcontrol treatment respectively The percentage of adult emergence reduces to 0% at the concentration of 8% compared with control treatment in which it reach to 66.6%. The extraction atbothconcentrations 6,8% does not affect the germination rate

Abstract:

 The research concerned the study of the railway transport sector in selected countries that sought to raise the efficiency of the railway network and develop it, after realizing the importance of this vital sector, which is a link between it and the rest of the other economic sectors.

The research sought to explain the methods, methods and procedures adopted by these countries for the development of the railway sector, and to benefit from these experiments to improve the efficiency of the railway transport sector in Iraq.

The railway transport sector in Iraq suffers from the erosion of railway lines and mobile units such as locomotives, pas