The main objective of this research is to find out the effect of deviation in the aggregate gradients of asphalt mixtures from the Job Mix Formula (JMF) on the general mixture performance. Three road layers were worked on (wearing layer, binder layer, and base layer) and statistical analysis was performed for the data of completed projects in Baghdad city, and the sieve that carried the largest number of deviations for each layer was identified. No.8 sieve (2.36mm), No.50 sieve (0.3mm), and 3/8'' sieve (9.5mm) had the largest number of deviations in the wearing layer, the binder layer, and the base layer respectively. After that, a mixture called Mix 1, was made. This mixture was selected from a number of completed mixtures, and it represents the worst mixture. Mix 1 was compared with two other mixtures, Mix 2 and Mix 3, Mix 2 represents the mean of JMF for the gradients of aggregates, and Mix 3 is the same as Mix 1 except for the sieve that contains the largest number of deviations, so the gradient of aggregates for it is the mean of JMF. Fifteen Marshall specimens were made for each mixture and for each layer in order to know the differences in Marshall properties between the mixtures. Also, 6 specimens were made for each mixture (the total is 18 specimens for each layer) to check the indirect tensile strength, for the purpose of knowing the mixtures' susceptibility to moisture. Finally, 1 specimen was made for each mixture for repeated load test for the purpose of knowing the performance of the mixtures with respect to permanent deformation. The tests showed that the performance of Mix 2 and Mix 3 was improved in comparison with Mix 1. The deviation of the aggregate gradients in specific sieves may be higher than the limits of the JMF or it may be less, and in both cases, the implementation of a mixture like Mix 1 for the streets is bad for the performance of the road and failures occur due to the wrong implementation of the JMF. On the other hand, there are much better mixtures in all respects such as Mix 2 and Mix 3, and if they are implemented on the streets, they will certainly have much better.
The purpose of this paper is to present an approach to compute accurately the distributions of the frictional heat generated, contact pressure and thermal stresses at any instant during the sliding period (heating phase) of the single-disc friction clutch system works in the dry condition and the complex interaction among them.
Numerical work was achieved using the developed elastic and thermal finite element models (axisymmetric models) to simulate the engagement of the single-disc friction clutch system.
تحليل الشراكات التجارية للعراق 2003-2013
This paper presents numerical and experimental stress analyses to evaluate the contact and bending stresses on the teeth of spiral bevel gear drive. Finite Element Method has been adopted as a numerical technique which accomplished basically by using ANSYS software package. The experimental stress analysis has been achieved by using a gear tooth model made of Castolite material which has photoelastic properties. The main goal of this research is detecting the maximum tooth stresses to avoid the severe areas that caused tooth failure and to increase the working life for this type of gear drives.
An indoor spraying robot is built in this research to solve numerous challenges associated with manual spraying. The mechanical, hardware and essential technologies used are all detailed and designed. The proposed spraying robot's conceptual design is split into two parts: hardware and software. The mechanical design, manufacturing, electrical, and electronics systems are described in the hardware part, while the control of the robot is described in the software section. This robot's kinematic and dynamic models were developed using three links that move in the x, y, and z directions. The robot was then designed using SolidWorks software to compute each connection's deflection and maximum stresses. The characteristics of the stepper moto
... Show MoreIn recent decades, breeding deer populations in Iraq have expanded significantly in size and distribution. Owing to their role in pathogen transmission, these deer populations pose a risk to the livestock industry. However, little is known about the parasitic infection status of the breeding deer and the surrounding environment in Iraq. Atotal of 150 deer faecal samples were collected from male and female deer of various ages from four regions of Iraq and examined microscopically for intestinal parasites. Microscopic analysis revealed the presence of seven intestinal parasite species: Entamoeba spp. (48%), Giardia duodenalis (17%), Toxocara spp. (12%), Balantidium coli(9%), Taenia spp. (9%), Strongyloides spp. (3%) and Trichostrongy
... Show MoreBioremoval of chromium from wastewater of tannery factory in Iraq was studied. The bacteria Proteus vulgaris 7E showed an enhanced capability in biosorping chromium when its concentration increased in the solution, reaching a maximum of 476,7 mg/ ml out of 492 mg/ ml under optimum conditions at pH 6 and 50°C at one hour contact time and biomass of 1 mg/ml. The present results showed that dead cells of P. vulgaris 7E biosorbed 87.41 mg/ml of chromium in comparison with91.18 mg/ml of chromium biosorbed by living cells, this indicates the insignificant effect of physiological state of cells. It was found that the above biosorption is physico-chemical process depends upon electrostatic attraction forces. The results has illustrated that the
... Show MoreBackground: Dental implants provide a unique treatment modality for the replacement of a lost dentition .This is accomplished by the insertion of relatively an inert material (a biomaterial) into the soft and hard tissue of the jaws, there by providing support and retention for dental prostheses. Low level laser therapy (LLLT) is an effective tool used to prompt bone repair and remodeling, this has referred to the biostimulation effect of LLLT. The Aim of this study was to evaluate the effects of inflammatory cells on osseointegration of CpTi implant irradiated by low level laser. Materials and Methods: thirty two adult New Zealand white rabbits, received titanium implants were inserted in the tibia. The right side is considered as experime
... Show More