The main objective of this research is to find out the effect of deviation in the aggregate gradients of asphalt mixtures from the Job Mix Formula (JMF) on the general mixture performance. Three road layers were worked on (wearing layer, binder layer, and base layer) and statistical analysis was performed for the data of completed projects in Baghdad city, and the sieve that carried the largest number of deviations for each layer was identified. No.8 sieve (2.36mm), No.50 sieve (0.3mm), and 3/8'' sieve (9.5mm) had the largest number of deviations in the wearing layer, the binder layer, and the base layer respectively. After that, a mixture called Mix 1, was made. This mixture was selected from a number of completed mixtures, and it represents the worst mixture. Mix 1 was compared with two other mixtures, Mix 2 and Mix 3, Mix 2 represents the mean of JMF for the gradients of aggregates, and Mix 3 is the same as Mix 1 except for the sieve that contains the largest number of deviations, so the gradient of aggregates for it is the mean of JMF. Fifteen Marshall specimens were made for each mixture and for each layer in order to know the differences in Marshall properties between the mixtures. Also, 6 specimens were made for each mixture (the total is 18 specimens for each layer) to check the indirect tensile strength, for the purpose of knowing the mixtures' susceptibility to moisture. Finally, 1 specimen was made for each mixture for repeated load test for the purpose of knowing the performance of the mixtures with respect to permanent deformation. The tests showed that the performance of Mix 2 and Mix 3 was improved in comparison with Mix 1. The deviation of the aggregate gradients in specific sieves may be higher than the limits of the JMF or it may be less, and in both cases, the implementation of a mixture like Mix 1 for the streets is bad for the performance of the road and failures occur due to the wrong implementation of the JMF. On the other hand, there are much better mixtures in all respects such as Mix 2 and Mix 3, and if they are implemented on the streets, they will certainly have much better.
This paper deals with finite element modeling of the ultimate load behavior of double skin composite (DSC) slabs. In a DSC slab, shear connectors in the form of nut bolt technique studs are used to transfer shear between the outer skin made of steel plates and the concrete core. The current study is based on finite element analysis using ANSYS Version 11 APDL release computer program. Experimental programmes were carried out by the others, two simply supported DSC beams were tested until failure under a concentrated load applied at the center. These test specimens were analyzed by the finite element method and the analyses have shown that these slabs displayed a high degree of flexural characteristics, ultimate strength,
... Show MoreIn this paper, photometric analysis of two short period group of the eclipsing binaries (RS CVn); RT And and BH Vir is presented. New physical and geometric parameters were obtained by performing two computer modeling. The first model is software package PHOEBE based on the Wilson–Devinney method, and the second is Binary Maker 3 (BM3).Our results are in good agreement with those obtained using the same modeling.
Background: This study designed to shade light on the important role of CBCT in accurate localization of the impacted maxillary canines. Materials and method: Fifty two unilateral and bilateral impacted maxillary canines from 30 patients (24 females and 6 males) were evaluated by a volumetric 3D images obtained from cone beam CT. All samples attended to the specialist health center of dentistry in Al-Sadder City referred to CBCT by oral surgeons or orthodontists to detect the exact position of impacted upper canine in cases when there was no bulging buccally or palatally which aids to detect the exact position. Results: Mesio-palatal angulations had the highest rate (63.5%) followed by mesio-labial (19.2%), vertical (labial) (9.6%), disto-p
... Show MoreThe major objectives of this research are to analyze the behavior of road embankments
reinforced with geotextiles constructed on soft soil and describe the finite element analysis by using
ANSYS program ver. (5.4). The ANSYS finite element program helps in analyzing the stability of
geo- structure (embankment) in varied application of geotextiles reinforcement to enhance the best
design for embankment.
The results of analysis indicate that one of the primary function of geotextiles reinforcement was to
reduce the horizontal displacement significantly. With the inclusions of reinforcement, the horizontal
displacement reduced by about (81%), while the vertical displacement reduced by (32%). The effect
of geotextiles
The study was performed to analyze the oropharynx airway and examine the influence of age and gender on the oropharynx volume configuration using cone beam computed tomography.
This study examined the cone beam computed tomographic images of 51 patients 25 male and 26 females, group matched for age and gender. The oropharynx airway volume and area between the posterior nasal spine and top of the epiglottis were measured and compared.
This research aims to study the important of the effect of analysis of covariance manner for one of important of design for multifactor experiments, which called split-blocks experiments design (SBED) to deal the problem of extended measurements for a covariate variable or independent variable (X) with data of response variable or dependent variable Y in agricultural experiments that contribute to mislead the result when analyze data of Y only. Although analysis of covariance with discussed in experiments with common deign, but it is not found information that it is discussed with split-Blocks experiments design (SBED) to get rid of the impact a covariance variable. As part application actual field experiment conducted, begun at
... Show MoreMany researchers have tackled the shear behavior of Reinforced Concrete (RC) beams by using different kinds of strengthening in the shear regions and steel fibers. In the current paper, the effect of multiple parameters, such as using one percentage of Steel Fibers (SF) with and without stirrups, without stirrups and steel fibers, on the shear behavior of RC beams, has been studied and compared by using Finite Element analysis (FE). Three-dimensional (3D) models of (RC) beams are developed and analyzed using ABAQUS commercial software. The models were validated by comparing their results with the experimental test. The total number of beams that were modeled for validation purposes was four. Extensive pa
... Show MoreBackground: Oral cancer is a highly lethal and disfiguring disease. Squamous cell carcinoma of the oral cavity constitutes about 90% of all oral malignancies. The aims of the study was to achieve an epidemiological description of the oral squamous cell carcinoma in Iraq in general and in Iraqi governorates except Kurdistan region retrospectively during period 2001-2013 Materials and Methods: Data were collected from department of oral and maxillofacial pathology, college of dentistry, university of Baghdad, Nuclear medicine and radiotherapy hospital, Iraqi cancer registry center, Main hospitals in Baghdad and Iraqi governorates, Private labs. for histopathological examinations. The descriptive and inferential statistical methods were used
... Show MoreContemporary developments in various sciences and the impact of technological changes require an integrated vision of the activities and work of the organization in Iraq in light of the high costs of products and their low quality compared to imported products of high quality and low cost, and the need to use modern cost techniques based on a clear and specific philosophy that contributes to increasing the efficiency and effectiveness of management In the business environment and how it can contribute to reducing product costs and being environmentally friendly at the same time, it is no secret that the main goal of most organizations is to maximize profitability and reduce costs to the minimum, but this matter is not achieved autom
... Show MoreMorphometric traits or body conformation traits also called linear body measurements are important in predicting marketing body weight especially for commercial breeders and producers. The total number of reared Domyati ducklings are 168 hatched, at marketing age (8 wks.) 44 brown and 14 white Domyati ducks were used to estimate the body weight and body measurements such as shank length (ShL), keel length (KL), body circumference (BC), breast length (BrL), breast width (BrW), beak width (BL), and body length (BL). Our results showed that there is no significant difference between both white and brown Domyati ducks for body measurements. There was high positive correlation among body weight and body measurements on both white and bro
... Show More