This study investigated the potential of calcined clays from Nigerian deposits in the production of ternary blends of cement. Clay samples were obtained from three different locations namely: Ikpeshi, Okpilla and Uzebba. The raw clay samples were then calcined at 700°C and 800°C. Chemical and mineralogical compositions were determined for the raw and calcined clay samples using XRF and XRD respectively. The chemical composition confirmed these clays as potential pozzolans with SiO₂, Al₂O₃, and Fe₂O₃ collectively exceeding 70%. XRD analysis identified kaolinite and quartz as major mineral phases in the raw clays, which transformed into metakaolin upon calcination.

A new model for the non-linear propeller-pendulum system is derived in this study. The model takes into consideration the effects of external disturbances and the properties of the pendulum elements. Two systems with PID controllers are simulated. In the first system, Simulink is used to implement the system and tune the PID parameters. In the second system, a MATLAB script is used to simulate the system and tune the PID parameters. The scrip uses the Runge-Kutta method for solving the system’s equation and uses particle swarm optimization (PSO) to tune the parameters. Further, both systems were investigated under two disturbance conditions. The performance of these systems is evaluated based on comparing the settling

Non-biodegradability of rubber tires contributes to pollution and fire hazards in the natural environment. In this study, the flexural behavior of the Rubberized Reactive Powder Concrete (RRPC) beams that contained various proportions and sizes of scrap tire rubber was investigated and compared to the flexural behavior of the regular RPC. Fresh properties, hardened properties, load-deflection relation, first crack load, ultimate load, and crack width are studied and analyzed. Mixes were made using micro steel fiber of the straight type, and they had an aspect ratio of 65. Thirteen beams were tested under two loading points (Repeated loading) with small-scale beams (1100 mm, 150 mm, 100 mm) size.

The fine aggregate

اعتاد كثير من الناس النظر إلى الظل على انه ناتج عرضي لوجود الضوء والشكل(الجسم)،مثلما اعتادوا ان يكون
الظل دالة لوجود الشكل، فيكفي-مثلا- أن نرى ظل احد الأشكال لنوقن بوجوده، لكن، ماذا سيحصل لو قمنا باصطناع ذلك
الظل مع غياب الشكل الأصلي؟؟.
محاولة تفكيك العلاقة بين الشكل وظله وإمكانية الارتقاء بالظل ليكون عنصرا تصميميا مستقلا غير مرتبط لزوما
بوجود "شكل" مشابه له ،تلك هي مشكلة هذا البحث والتي سوف يحاول سبر أ

Constructional Efficiency in architecture in general is one of the most important standard success for any structure and a measure of its continuity and relevance across time and space. Given the importance of Al-Ahwaar environment that owned the spatial, environmental, economic and social elements had a prominent impact in creation of architecture patterns form to create special architectural and structural environment, which had many qualities and ingredients that contributed to its continuity and existence over the years. From the premise that man and his environment is the main goal to any architectural style,

Thus the research problem focusing on the lack of clarity of the previous literatures in its st

A new design concept for a percolator is developed which combine the simultaneous production of ammonia vapor plus the pumping of weak aqua ammonia liquid. The steady state desig was based on a balance between the hydrostatic driving head and the total single and two-phase pressure losses in the percolator system. To accomplish this, the results from modeling of the driving pressure and pressure losses, using the separated flow and drift flux methods were compared with the experimental measurements. The Chisholm's model was the best in predicting the measured flow rate versus water level for first stage with a maximum standard deviation of ± 10.1% and was adopted for the theoretical calculations. Parametric design studies that include t

Total quality management  considers one of the modern scientific entrances  which practiced by productivity service organizations alike to provide appropriate quality required outputs according to the needs and desires of customers manage , enable the organization seeking to continue and grow in light of the increasing competition from the satisfy and provide the appropriate total quality management requirements whenever led to face risks that they may have  in a manner in which they can be addressed and find ways to avoid them in the future when repeated.                          &n

This paper deals with the using of Geographic Information Systems to build up analytical model to choose the best locations of new schools within the study area. This has been done by using satellite image of Baghdad city. Then multi themes digital maps were prepared to the study area. These can be used to update their data by using Geographic Information Systems software. Then, an analytical had been prepared to create the best probable locations, for new primary schools, depending on criteria, scientific technical specifications. Finally, we prepared layouts with geographical geometrical specifications for these proposed locations. 

The aesthetic and architectural shapes of the beam-column elements may enhance the elements strength depending on the maximum and minimum bending moments effect. Therefore, the stability value of the non-linear taper member in concave configuration may be more efficient than linear taper or prismatic members. The modified stability functions will be obtained from the solution of the basic differential equation, where this basic differential equation depends on the non-linearity factor of the beam-column shape and the shape factor of the cross-sectional area. These two factors, multiplied by others, produce the modified shape factor, which affects the results of the basic differential equation solutions.

The aim of this research was to apply a numerical model capable of describing the thermal pollution in rivers. For this purpose a two-dimensional numerical model was applied for estimating temperature distribution in a river Momentum Conservation Equation and Thermal Energy Equation were used to describe the fdistribution and diffusion of temperature along the river subjected to thermal pollution point source. Furthermore the model incorporates the (k-e) turbulence model to calculate the distribution of turbulent viscosity The pressure distribution was determined using hydrostatic pressure equation. The partial differential equations were formalized and simplified to be solved using Alternative direction implicit- explicit method (ADI) w

An experimental study was performed to estimate the forced convection heat transfer performance and the pressure drop of a single layer graphene (GNPs) based DI-water nanofluid in a circular tube under a laminar flow and a uniform heat flux boundary conditions. The viscosity and thermal conductivity of nanofluid at weight concentrations of (0.1 to 1 wt%) were measured. The effects of the velocity of flow, heat flux and nanoparticle weight concentrations on the  enhancement of the heat transfer are examined. The Nusselt number of the GNPs nanofluid was enhanced as the heat flux and the velocity of flow rate  increased, and the maximum Nusselt number  ratio (Nu nanofluid/ Nu base fluid)   and thermal performance factor

In this paper, Wavelet-Network (WN) model has been recently proposed and applied to image processing, e.g., identification type of noise in Gray-Scale Images (GSI). This paper develops a new technique, which employs a Discrete Wavelet Transform (DWT) and an Artificial Neural Network (ANN). This WN technique uses special mother wavelet y(xl,x2) of (DWT) as activation function for (ANN) instead of the traditional activation functions like (Log sigmoid, Tan sigmoid, etc). It is shown here that the benefit of WN circuits which uses WN is a good approximation tool for GSI images. These approximation patterns for images forced ANN to learn on these images which will be used in the test phase after that.

A Tonido cloud server provides a private cloud storage solution and synchronizes customers and employees with the required cloud services over the enterprise. Generally, access to any cloud services by users is via the Internet connection, which can face some problems, and then users may encounter in accessing these services due to a weak Internet connection or heavy load sometimes especially with live video streaming applications overcloud. In this work, flexible and inexpensive proposed accessing methods are submitted and implemented concerning real-time applications that enable users to access cloud services locally and regionally. Practically, to simulate our network connection, we proposed to use the Raspberry-pi3 m

Turbidity is a visual property of water that expresses the amount of suspended substances in the water. Its presence in quantities more significant than the permissible limit makes the water undrinkable and reduces the effectiveness of disinfectants in treating pathogens. On this basis, turbidity is used as a basic indicator for measuring water quality. This study aims to evaluate the removal efficiency of AL- Muthanna WTP. Water turbidity was used as a basic parameter in the evaluation, using performance improvement evaluation and data from previous years (2016 to 2020). The average raw water turbidity was 26.7 NTU, with a minimum of 14 NTU, with a maximum of 48 NTU. Water turbidity value for 95% of settling daily readi

This paper deals with testing defected model piles in the soil in order to study their behavior. In this respect, the results of model pile tests are discussed either geotechnically or structurally according to the type of failure.

Two parameters were studied in order to evaluate the general behavior of defective piles. These parameters include the defect location and the defect type for floating and end bearing pile. The results of the experimental work indicated that the critical case for floating pile is seen to be when the defect of (5%) at the first third of the pile length at which the decrease in the bearing capacity is about (21%), while the decrease in the bearing capacity is found to be (

In this paper a decoder of binary BCH code is implemented using a PIC microcontroller for code length n=127 bits with multiple error correction capability, the results are presented for correcting errors up to 13 errors. The Berkelam-Massey decoding algorithm was chosen for its efficiency. The microcontroller PIC18f45k22 was chosen for the implementation and programmed using assembly language to achieve highest performance. This makes the BCH decoder implementable as a low cost module that can be used as a part of larger systems. The performance evaluation is presented in terms of total number of instructions and the bit rate.

In wireless broadband communications using single-carrier interleave division multiple access (SC-IDMA) systems, efficient multiuser detection (MUD) classes that make use of joint hybrid decision feedback equalization (HDFE)/ frequency decision-feedback equalization (FDFE) and interference cancellation (IC) techniques, are proposed in conjunction with channel coding to deal with several users accessing the multipath fading channels. In FDFE-IDMA, the feedforward (FF) and feedback (FB) filtering operations of FDFE, which use to remove intersymbol interference (ISI), are implemented by Fast Fourier Transforms (FFTs), while in HDFE-IDMA the only FF filter is implemented by FFTs. Further, the parameters involved in the FDFE/

Microbial antibiotics resistance is considered a serious health issue in the Middle East and developing countries. In this study, the Fe₂O₃ nanoparticles was prepared chemically, and the particles size and shape were analyzed by using Scan electron microscope (SEM) and X-Ray diffraction (XRD). Different concentration of Fe₂O₃ nanoparticles were used and examined on E.coli and S. aureus. Using liquid dilution and in vitro cytotoxicity assay by microplate toxicity test (MTT). The microbial cell metabolic activity was measured on gram-negative, gram-positive bacteria and fungi after treating with different concentrations of Fe₂O₃ nanoparticl

The optimum trajectory of a single or multi-stage satellite launcher guided with proportional
navigation guidance (PNG) is addressed. The PNG is extended to compensate for the gravity effect.
For the trajectory optimization problem, the launcher is modeled as a mass point flying around the
center of the Earth. To provide a completely valid analysis, all known influences on the launcher
trajectory have been considered; Empirical equations have been used in order to model the Earth
standard atmosphere in SI units. A computer program had been constructed in order to simulate the
trajectory of such launcher from the available initial conditions. Pegasus launcher is used as a
hypothetical example. The simulator results

Moisture damage is a primary mode of distress occurring in hot mix asphalt (HMA) pavements in Iraq. Because of the loss of bond, or stripping, caused by the presence of moisture between the asphalt and aggregate, which is a problem in some areas and can be severe in some cases, it is requires to evaluate the design asphalt mixture to moisture susceptibility. Many factors such as aggregate characteristics, asphalt characteristics, environment, traffic, construction practices and drainage can contribute to stripping. Asphalt concrete mixes were prepared at their optimum asphalt content by superpave system and then tested to evaluate their engineering properties, which include tensile strength, resilient modulus, and perman

تعمل أطقم الأسنان النظيفة على تعزيز صحة المريض، وطول عمر طقم الأسنان، ونوعية الحياة العامة عن طريق منع التلوث المتبادل. يجب ألا يؤدي أسلوب التنظيف الفعال إلى إتلاف المواد الأساسية للطقم. تبحث هذه الدراسة في صلابة وامتصاص الأشعة فوق البنفسجية وامتصاص الماء وقابلية ذوبان راتنج الأكريليك المعالج بالحرارة بعد 180 مرة من الغمر في منظف طقم الأسنان بزيت شجرة الشاي. تم إجراء تسعين عينة من راتينج الأكر

The effective stress method is developed to predict the axial capacity of piles in clay. This
method is based on the principle that, at failure, the available shear resistance at the pile soil
interface is related to the mean normal effective stress at the pile face and the effective stress
friction angle for the soil sliding on the pile material.
In this paper, the coupled non-linear finite element method is used to analyze some pile-soil
interaction problems. This computer program ( CRISP ) is used for this task. Eight- node
isoparametric elements were used for displacements while four- node elements are used for
pore pressure. Interface elements are used to simulate the interaction between the pile and the

This paper deals with an up to date problem for oil and gas industry- separation of the gas -fluid fogs. Here is described the worked out physical model of the gas movement process in the sections of the inertial filtering (IF) gas separators. One can find the mathematical model for research of the fields of velocities and pressures in the inertial curvilinear channel. The main simplifications and assumptions are explained. This mathematical model has been made using mathematical program Maple and it is received the 3-d graphic of the distribution componential speed parts in the channel and also 2-d graphics at the channel sectional view when the flow is flat. The new method for gas - fluid systems separation is suggested.

In this work an experimental study is performed to evaluate the thermal performance
of locally made closed loop solar hot water system using a shell and helical coiled tube
heat exchanger as a storage tank. Several measurements are taken include inlet and outlet
temperatures of both collectors and supply water and temperature distribution within the
storage tank. This is beside the water flow rate in both collectors and load cycle. The
main parameters of the system are obtained.

In this research the results of applying Artificial Neural Networks with modified activation function to
perform the online and offline identification of four Degrees of Freedom (4-DOF) Selective Compliance
Assembly Robot Arm (SCARA) manipulator robot will be described. The proposed model of
identification strategy consists of a feed-forward neural network with a modified activation function that
operates in parallel with the SCARA robot model. Feed-Forward Neural Networks (FFNN) which have
been trained online and offline have been used, without requiring any previous knowledge about the
system to be identified. The activation function that is used in the hidden layer in FFNN is a modified
version of the wavelet func

Theoretical and experimental investigations have been carried out on developing laminar
combined free and forced convection heat transfer in a vertical concentric annulus with uniformly
heated outer cylinder (constant heat flux) and adiabatic inner cylinder for both aiding and opposing
flows. The theoretical investigation involved a mathematical modeling and numerical solution for
two dimensional, symmetric, simultaneously developing laminar air flows was achieved. The
governing equations of motion (continuity, momentum and energy) are solved by using implicit
finite difference method and the Gauss elimination technique. The theoretical work covers heat flux
range from (200 to 1500) W/m2, Re range from 400 to 2000 an

The static characteristics of porous floating ring journal bearing under hydrodynamic
lubrication condition when operating with an improved boundary conditions are theoretically
analyzed. An isothermal finite bearing theory was adopted during this analysis. The effect of
different parameters, namely, permeability, geometrical dimensions of the ring and the bearing are
considered. It was assumed that oil is supplied through the outside diameter of the bearing under
low supply pressure. The angular extent of the oil – film formed in journal – ring and ring – bearing
oil films was obtained by applying the integral momentum equation at the leading edge of the oil –
film to define the beginning of the oil e

In this research, the structural behavior of reinforced concrete columns made of normal and hybrid reactive powder concrete (hybrid by steel and polypropylene fibers) subjected to chloride salts with concentration was 8341.6 mg/l. The study consists of two parts, the first one is experimental study and the second one is theoretical analysis.  Three main variables were adopted in the experimental program; concrete type, curing type and loading arrangement. Twenty (120x120x1200) mm columns were cast and tested depending on these variables. The samples were reinforced using two different bars; Ø8 for ties and Ø12 with minimum longitudinal reinforcement (0.01Ag). The specimens were divided into two main groups based o