The calculation. of the nuclear. charge. density. distributions. ρ(r) and root. mean. square. radius.( RMS ) by elastic. electron. scattering. of medium. mass. nuclei. such. as (⁹⁰Zr, ⁹²Mo) based. on the model. of the modified. shell. and the use of the probability. of occupation. on the surface. orbits. of level 2p, 2s eroding. shells. and 1g gaining. shells. The occupation probabilities of these states differ noticeably from the predictions of the SSM. We have found. an improvement. in the determination. of ground. charge. density. and this improvement. allow. more precise. identification. of (CDD) between. (⁹²Mo- ⁹⁰Zr) to illustrate the influence of the extra

Ceramic coating compose from a ceramic mixture (MgO, Al₂O₃) and metall (Al-Ni) were produced by Thermal Spray Technique. The mixed ratio of used materials Al:Ni (50%) and 40% of Al₂O₃ and 10% MgO. This mixture was spray on a stainless steel substrate of type (316 L) by using thermal spray with flame method and at spraying distances (8, 12, 16 and 20) cm, then the prepared films were treated by laser and thermal treatment. After that performing a hardness and adhesion tests were eximined. The present study shows that the best value of the thermal treatment is 1000 ℃ for 30 mint; the optimum spray distance is 12 cm and most suitable laser is 500 mJ where the microscopic and mechanical character

In this study, phosphorescence analysis (KPA) is used for determining soil collected from the Tigris River from Al- Karrada and Bab Al-Sharq in Baghdad and samples were taken from rainwater collected from Al-Rashad, Al-Obeidi, Al-Dora and Al-Sadr City in Baghdad. The measurements were carried out by the Iraqi Ministry of Health and Environment, in the Radiation Protection Center. The collection, removal and evaporation of the samples ranged from January to the end of March 2018. The results show the presents of concentration of 238U and 235U in soil samples and the rainwater samples. The conclusion of this work is the concentration of uranium in soil samples is more than recommendations by ICRP value of 1.9 μg /l. While all water sample

Gamma - irradiation effect on polymethylmethacrylate (PMMA) samples has been studied using Positron Annihilation Lifetime (PAL) method. The orthopositronium (o-Ps) lifetime τ₃, hence the o-ps parameters, the volume hole size (V_h) and the free volume fraction (Ꞙ_h) in the irradiated samples were measured as a function of gamma-irradiation dose up to 28.05 kGy. It has been shown that τ ₃, V_h, and Ꞙ_h, are increasing in general with increasing gamma-dose, to reach a maximum percentage increment of 22.42% in τ₃, 60% in V_h and 29.5% in Ꞙ_h, at. 2.55 kGy, whereas τ₂ reaches maximum increment of 119. 7% at 7.65 kGy. The results s

In the present work, a d.c. magnetron sputtering system was designed and fabricated. The chamber of this system was includes from two copper coaxial cylinders where the inner one used as a cathode (target) while the outer one used as the anode with Solenoid magnetic coil located on the outer cylinder (anode). The axial profile of magnetic field for various coil current (from 2A to 14 A) are shown. The plasma characteristics in the normal glow discharge region are diagnostics by the 2.2mm diameter Langmuir probe with different length along the cathode and located at different radial positions 1cm and 2cm from the cathode surface. The result of this work shows that, the electron energy distributions at different radial positions along the

The biggest problem of structural materials for fusion reactor is the damage caused by the fusion product neutrons to the structural material. If this problem is overcomed, an important milestone will be left behind in fusion energy. One of the important problems of the structural material is that nuclei forming the structural material interacting with fusion neutrons are transmuted to stable or radioactive nuclei via (n, x) (x; alpha, proton, gamma etc.) reactions. In particular, the concentration of helium gas in the structural material increases through deuteron- tritium (D-T) and (n, α) reactions, and this increase significantly changes the microstructure and the properties of the structural materials. T

paper

This study focuses on synthesizing Niobium pentoxide (Nb₂O₅) thin films on silicon wafers and quartz substrates using DC reactive magnetron sputtering for NO₂ gas sensors. The films undergo annealing in ambient air at 800 °C for 1 hr. Various characterization techniques, including X-ray diffraction (XRD), atomic force microscopy (AFM), energy-dispersive X-ray spectroscopy (EDS), Hall effect measurements, and sensitivity measurements, are employed to evaluate the structural, morphological, electrical, and sensing properties of the Nb₂O₅ thin films. XRD analysis confirms the polycrystalline nature and hexagonal crystal structure of Nb₂O₅. The optical band gap val

In this study, pure Co3O4 nano structure and doping with 4 %, and
6 % of Yttrium is successfully synthesized by hydrothermal method.
The XRD examination, optical, electrical and photo sensing
properties have been studied for pure and doped Co3O4 thin films.
The X-ray diffraction (XRD) analysis shows that all films are
polycrystalline in nature, having cubic structure.
The optical properties indication that the optical energy gap follows
allowed direct electronic transition calculated using Tauc equation
and it increases for doped Co3O4. The photo sensing properties of
thin films are studied as a function of time at different wavelengths to
find the sensitivity for these lights.
High photo sensitivity dope

The properties of structural and optical of pure and doped nano titanium dioxide (TiO₂) films, prepared using chemical spray pyrolysis (CPS) technique, with different nanosize nickel oxide (NiO) concentrations in the range (3-9)wt% have been studied. X-Ray diffraction (XRD) technique where using to analysis the structure properties of the prepared thin films. The results revealed that the structure properties of TiO₂ have polycrystalline structure with anatase phase. The parameters, energy gap, extinction coefficient, refractive index, real and imaginary parts were studied using absorbance and transmittance measurements from a computerized ultraviolet visible spectrophotometer (Shimadzu UV-1601 PC) in the wavelength

PMMA/TiO2 homogeneous thin films were deposited by using plasma jet system under normal atmospheric pressure and room temperature. PMMA/TiO2 nanocomposite thin film synthesized by plasma polymerization. Titanium oxide was mixed with Methyl Methacrylate Monomer (MMA) with specific weight ratios (1, 3 and 5 grams of TiO2 per 100 ml of MMA). Optical properties of PMMA/TiO2 nanocomposite thin films were characterized by UV-Visible absorption spectra using a double beam UV-Vis-NIR Spectrophotometer. The thin films surface morphological analysis is carried out by employing SEM. The structure analysis are achieved by X-ray diffraction. UV-Visible absorption spectra shows that the increasing the concentration of titanium oxide added to the polym

In this work, polyvinylpyrrolidone (PVP)/ Multi-walled carbon nanotubes (MWCNTs) nanocomposites were prepared with two concentrations of MWCNTs by casting method. Morphological, structural characteristics and electrical properties were investigated. The state of MWCNTs dispersion in a PVP matrix was indicated by Field Effect-Scanning Electron Microscopy (FESEM) which showed a uniform dispersion of MWCNTs within the PVP matrix. X-ray Diffraction (XRD) indicate strong bonding of carbonyl groups of PVP composite chains with MWCNTs. Fourier transfer infrared (FTIR) studies shows characteristics of various stretching and bending vibration bands, as well as shifts in some band locations and intensity changes in others. Hall effect was studied

In this work, using the spin coating method to create polyvinylidene fluoride (PVDF)/polyethylene oxide (PEO) thin films, the effects of nano-tungsten oxide (WO₂) doping were investigated. The novelty of this research lies in its investigation of varying weight concentrations of WO₂ nanoparticles (NPs) within the composite films. Comprehensive characterization techniques were employed, including structural analysis via X-ray diffraction (XRD), which revealed a clear and prominent peak in the XRD of the PVDF/PEO films, and the films' polycrystalline nature with tetragonal structures. The grain size was noted to increase with higher WO₂ NPs doping. Field emission scanning electron microscopy (FE-SEM) showed

To evaluate the efficacy of the Erbium, Chromium-doped Yttrium Scandium Gallium Garnet laser (Er,Cr:YSGG) in sealing dentinal tubules with the incorporation of multi-walled carbon nanotubes (MWCNTs) paste, and without, when used on exposed dentin. Thirty-nine natural posterior teeth were prepared, sectioned, cleaned, and made ready for treatment. Samples were split into 3 groups: Group G1 is the control group (N=10). Group G2 (N=10) was exposed for 2 seconds to a 2780 nm Er,Cr:YSGG laser (Waterlase iPlus, Biolase Technology) in the free-running pulse mode, with 0.25 W power, 20 Hz frequency, a pulse width of 60 μs, a fibre tip size of 600 μm, and non-contact mode, and Group G3 (N=10) was exposed to Er,Cr:YSGG with carbon nanotubes (CNT

In this study, the Single-Mode Fiber (SMF) was examined in a theoretical investigation of the impact of the medium on the two Whispering Gallery Mode Resonator (WGMR) models using MATLAB software. It was found that the Free Spectral Range (FSR) has an inverse relationship with the resonator radius, and it was equal to 0.33 THz. The low FSR value is caused by the big microsphere resonator. A high Q-factor is defined as 0.175 x 10⁵. The resonance spectrum was found to diminish when the surrounding media's refractive index rose. The WGMR's evanescent field interacts with the external medium more strongly when the surrounding environment’s refractive index increases. The resonant modes' boundary conditions were altered by this i

This study investigates the electrical and optical properties of polyaniline (PANI) composites incorporating graphene oxide (GO) and metal oxides such as tin dioxide (SnO₂) and tungsten trioxide (WO₃). The addition of GO improves charge transport due to its high surface area and conductive nature. Moreover, SnO₂ contributes to stabilizing the electrical conductivity of the composites over time, while WO₃ introduces frequency-dependent charge-trapping behavior that influences dynamic electrical responses. Optically, GO modifies the bandgap and enhances UV-visible light absorption through improved photon interaction. SnO₂ improves the spectral stability of the composites, and WO₃ fine-tunes the wavelength-dependent optical resp

In this work, gold/ titanium oxide: cadmium sulfide (Au/TiO₂:CdS) thin film nanocomposites as photocatalysts were synthesized using the sol-gel technique and deposited on glass substrates using the dipping method for the degradation of Methylene Blue (MB) dye in water. The CdS doping with TiO2 at ratios 1:1, 0.25, and 0.5 wt%. Au/TiO₂: CdS thin film characterization was achieved using X-ray diffraction (XRD), atomic force microscopy (AFM), Raman spectroscopy, field effect electron scanning microscopy (FESEM), and UV-Vis spectroscopy. The results of XRD showed that the obtained phase of TiO₂: CdS was cubic. The results of AFM showed that the distribution of grain sizes increased with increasing CdS concentration, as did the roughnes

Dust storms frequent in Iraq can have far-reaching consequences for the distribution and abundance of heavy and trace elements within the soil, ultimately influencing the dynamics of ecosystems. This study aims to identify the sources of the severe dust storm in Iraq on May 16, 2022, and assess the heavy element pollution and their environmental impacts. The results revealed that the hybrid-single-particle-Lagrange-integrated trajectory (HYSPLIT) model trajectory of the dust storm agreed with MODIS visuals. The primary dust storm sources are identified as follows: the first source is from the shared border region between Syria (south of Rif-Dimasshq) and Jordan (north of Al-Ruwaished), and the second is from the northwestern area of Iraq

Tetragonal compound CuAl0.4Ti0.6Se2 semiconductor has been prepared by
melting the elementary elements of high purity in evacuated quartz tube under low
pressure 10-2 mbar and temperature 1100 oC about 24 hr. Single crystal has been
growth from this compound using slowly cooled average between (1-2) C/hr , also
thin films have been prepared using thermal evaporation technique and vacuum 10-6
mbar at room temperature .The structural properties have been studied for the powder
of compound of CuAl0.4Ti0.6Se2u using X-ray diffraction (XRD) . The structure of the
compound showed chalcopyrite structure with unite cell of right tetragonal and
dimensions of a=11.1776 Ao ,c=5.5888 Ao .The structure of thin films showed

In this study, an easy, low-cost, green, and environmentally
friendlier reagents have been used to prepare CdS QDs, in chemical
reaction method by mixed different ratio of CdO and sulfur in
paraffin liquid as solvent and oleic acid as the reacting media in
different concentration to get the optimum condition of the reaction
to formation CdS QDs. The results give an indication that the
behavior is at small concentration of 4ml of the oleic acid is best
concentration which give CdS QDs of small about to 9.23 nm with
nano fiber configuration.

In this paper, photometric analysis of two short period group of the eclipsing binaries (RS CVn); RT And and BH Vir is presented. New physical and geometric parameters were obtained by performing two computer modeling. The first model is software package PHOEBE based on the Wilson–Devinney method, and the second is Binary Maker 3 (BM3).Our results are in good agreement with those obtained using the same modeling.

This study includes the direct influence of (single & multi) dose of Cold Atmospheric Plasma (CAP) on the no. of platelets for mice for different exposure time (15, 30, 60, and 120) sec. the influence of CAP on mice was measured after 1, 2, 3, 7, and 14 day from exposure.
The results obtained in this study indicate that the effect of low doses of CAP on platelets was stimulatory effect in the first few hours from exposure (1day) but the high dose was inhibitory, It was found that after two weeks of exposure that the number of platelets became normal comparable to the control one, and this indicates that plasma effect was removed after this period.

The inelastic longitudinal electron scattering form factors are calculated for the low-lying excited states of 7Li {the first excited state 2121TJ (0.478 MeV) and the second excited state 2127TJ (4.63 MeV)}. The exact value of the center of mass correction in the translation invariant shell model (TISM) has been included and gives good results. A higher 2p-shell configuration enhances the form factors for high q-values and resolves many discrepancies with the experiments. The data are well described when the core polarization (CP) effects are included through effective nucleon charge. The results are compared with other theoretical models.
Keyword: 7Li inelastic electron scattering form factors calculated with exact

The specific activities of the natural radionuclides U-238 and Th-
232 and K-40 in 14 soil samples collected from different sites from
AL-Mustansiriyah university at two depths (topsoil "surface" and
20cm depth) were be investigated using gamma ray spectrometer
3"x3" NaI(Tl) scintillation detector.
The analysis of the energy spectra of the soil samples show that
these samples have specific activities ranging with (16.08-51.11)
Bq/kg for U-238, (14.79-52.29) Bq/kg for Th-232 and (191.08-
377.64) Bq/kg for K-40, with an average values of 29.37, 34.14 and
289.62 Bq/kg for U-238, Th-232, k-40 respectively. The radiation
hazard parameters of the natural radionuclides; radium equivalent
activity (Raeq), gamma a

Cadmium selenide (CdSe) nanocrystals, modified with water-soluble L-cysteine and known as CdSe/Cys nanocrystals, were synthesized using L-cysteine as a stabilizing agent. This synthesis process ensured the formation of highly stable nanocrystals with desirable properties for various applications. The CdSe/Cys nanocrystals were carefully studied using advanced methods to understand their structure, composition, and optical features in detail. The peak that shows the preferred (111) orientation of L-cysteine-capped CdSe matches the usual core components, as indicated by the XRD pattern. On the other hand, the peaks at (220) and (311) are not as prominent. Photoluminescence (PL) spectroscopy was conducted to study the optical properties of

This research shows how to prepare polyvinyl alcohol (PVA) films with silver nanoparticles and how different amounts of these nanoparticles affect the films' properties. The silver nanoparticles (AgNPs), featuring a uniform spherical shape, were synthesised using the chemical reduction method. The concentration of AgNPs and the amount of the reducing agent were found to influence the structural and optical characteristics of the prepared films. Higher volumes of the reducing agent have resulted in the formation of larger silver nanoparticles. These factors affected the size of the silver nanoparticles and the specific absorption peak, which was between 420 and 435 nm, with the nanoparticles measuring between 20 and 32 nm in size

Nuclear emission rates for nucleon-induced reactions are theoretically calculated based on the one-component exciton model that uses state density with non-Equidistance Spacing Model (non-ESM). Fair comparison is made from different state density values that assumed various degrees of approximation formulae, beside the zeroth-order formula corresponding to the ESM. Calculations were made for 96Mo nucleus subjected to (N,N) reaction at Emax=50 MeV. The results showed that the non-ESM treatment for the state density will significantly improve the emission rates calculated for various exciton configurations. Three terms might suffice a proper calculation, but the results kept changing even for ten terms. However, five terms is found to give

Many diseases can produce cardiac overload, of these disease hypertension, valve disease congenital anomaly in addition to many other disease. One of the most common diseases causing left ventricle overload is hypertension. A long term hypertension can cause myocardium hypertrophy leading to changes in the cardiac contractility and reduced efficiency. The investigations were carried out using conventional echocardiography techniques in addition to the tissue Doppler imaging (TDI) from which many noninvasive measurements can be readily obtained. The study has involved the effect of hypertension on the myocardium stiffness index through the measurement of early diastolic filling (E) and the early velocity of lateral mitral annulus (E_a

In this work, chemical oxidation was used to polymerize conjugated polymer "Polypyrrole" at room temperature Graphene nanoparticles were added by in situ-polymerization to get (PPY-GN) nano. Optical and Electrical properties were studied for the nanocomposites. optical properties of the nanocomposites were studied by UV-Vis spectroscopy at wavelength range (200 -800 nm). The result showed optical absorption spectra were normally determined and the result showed that the maximum absorbance wave length at 280nm and 590nm. The optical energy gap has been evaluated by direct transition and the value has decreased from (2.1 eV for pure PPy) to (1.3 eV for 5 %wt. of GN). The optical constants such as the band tail width ΔE was evaluated, the