The Maxwell equations have been formulated for a composite slab waveguide at x-band wave propagation. The eigenvalues of the system equations are obtained by using MATLAB program. These eigenvalues are used to obtain the wave propagation constant and a number of modes inside the slabs. A good correspondence was seen between the number of modes and the cut off thickness. The parameter that affects the performance of waveguide is the slab thickness. The propagation constant is usually adopted to characterize this type of waveguide and show how the cutoff frequency of the mode in the slab is increased dramatically by decreasing the frequency.
Our study focused on lower modes, the results for the transmission coefficient are then used to

PV connected systems are worldwide installed because it allows consumer to reduce energy consumption from the electricity grid. This paper presents the results obtained from monitoring a 1.1 kWp. The system was monitored for nine months and all the electricity generated was fed to the fifth floor for physics and renewable energy building   220 V, 50 Hz. Monthly, and daily performance parameters of the PV system are evaluated which include: average generated of system Ah per day, average system efficiency, solar irradiation around these months. The average generated kWh per day was 8 kWh/day, the average solar irradiation per day was 5.6 kWh/m²/day, the average inverter efficiency was 95%, the average modules efficien

In this work, silicon nitride (Si₃N₄) thin films were deposited on metallic substrates (aluminium and titanium sheets) by the DC reactive sputtering technique using two different silicon targets (n-type and p-type Si wafers) as well as two Ar:N₂ gas mixing ratios (50:50 and 70:30). The electrical conductivity of the metallic (aluminium and titanium) substrates was measured before and after the deposition of silicon nitride thin films on both surfaces of the substrates. The results obtained from this work showed that the deposited films, in general, reduced the electrical conductivity of the substrates, and the thin films prepared from n-type silicon targets using a 50:50 mixing ratio and deposited on both

The ground state proton, neutron and matter densities of exotic ¹¹Be and ¹⁵C nuclei are studied by means of the TFSM and BCM. In TFSM, the calculations are based on using different model spaces for the core and the valence (halo) neutron. Besides single particle harmonic oscillator wave functions are employed with two different size parameters  B_c and B_v.  In BCM, the halo nucleus is considered as a composite projectile consisting of core and valence clusters bounded in a state of relative motion. The internal densities of the clusters are described by single particle Gaussian wave functions.

 Elastic electron scattering proton f

Crystalline silicon (c-Si) has low optical absorption due to its high surface reflection of incident light. Nanotexturing of c-Si which produces black silicon (b-Si) offers a promising solution. In this work, effect of H₂O₂ concentrations towards surface morphological and optical properties of b-Si fabricated by two-step silver-assisted wet chemical etching (Ag-based two-step MACE) for potential photovoltaic (PV) applications is presented. The method involves a 30 s deposition of silver nanoparticles (Ag NPs) in an aqueous solution of AgNO₃:HF (5:6) and an optimized etching in HF:H₂O₂:DI H₂O solution under 0.62 M, 1.85 M, 2.47 M, and 3.7 M concentrations of H₂O<

The current study used extracts from the aloe vera (AV) plant and the hibiscus sabdariffa flower to make Ag-ZnO nanoparticles (NPs) and Ag-ZnO nanocomposites (NCs). Ag/ZnO NCs were compared to Ag NPs and ZnO NPs. They exhibited unique properties against bacteria and fungi that aren't present in either of the individual parts. The Ag-ZnO NCs from AV showed the best performance against E. coli, with an inhibition zone of up to 27 mm, compared to the other samples. The maximum absorbance peaks were observed at 431 nm and 410 nm for Ag NPs, at 374 nm and 377 nm for ZnO NPs and at 384 nm and 391 nm for Ag-ZnO NCs using AV leaf extract and hibiscus sabdariffa flower extract, respectively. Using field emission-scanning electron microscopes (FE-

Low-pressure capacitively coupled RF discharge Ar plasma has been studied using Langmuir probe. The electron temperature, electron density and Debay length were calculated under different pressures and electrode gap. In this work the RF Langmuir probe is designed using 4MHz filter as compensation circuit and I-V probe characteristic have been investigated. The pressure varied from 0.07 mbar to 0.1 mbar while electrode gap varied from 2-5 cm. The plasma was generated using power supply at 4MHz frequency with power 300 W. The flowmeter is used to control Argon gas flow in the range of 600 standard cubic centimeters per minute (sccm). The electron temperature drops slowly with pressure and it's gradually decreased when expanding the electro

In this research, porous silicon (PS) prepared by anodization etching on surface of single crystalline p-type Si wafer, then Gold nanoparticle (AuNPs) prepared by pulsed laser ablation in liquid. NPs deposited on PS layer by drop casting. The morphology of PS, AuNPs and AuNPs/PS samples were examined by AFM. The crystallization of this sample was characterized by X-ray diffraction (XRD). The electrical properties and sensitivity to CO2 gas were investigated to Al/AuNPs/PS/c-Si/Al, we found that AuNPs plays crucial role to enhance this properties.

This study presents a strategy to increase the efficiency of dye-sensitized solar cells (DSSCs) by doping titanium dioxide (TiO₂) with different magnesium (Mn) concentrations (1, 3, 5, 7, and 9%) generated by the sol-gel process and effectively employed as a photo-anode (the working electrode) for DSSCs. The Doctor Blade method coated the indium-doped tin oxide (ITO) glass with a thin film layer. X-ray diffraction (XRD) was used to evaluate the characteristics of undoped and manganese-doped TiO₂, and the results demonstrate that all of the thin films are anatase. The samples were examined using XRD to assess grain size before and after Mn doping. The spectrum of UV-Vis absorption changes; accordingly, as doping incr

This study aimed to investigate the structure and optical properties of Sn nanostructures. Thin tin (Sn) films were deposited on glass substrates using the pulsed laser deposition method. Nd:YAG laser with fundamental wavelengths of 532 nm and 1064 nm was used to create Sn nanostructures with varying energies of 400 mJ to 700 mJ and the same frequency of 6 Hz. The tin powder was compressed into a disc with a one-centimetre diameter to serve as a sample. The X-ray diffraction (XRD) pattern showed a crystalline structure with several Sn nanostructures peaks at various energies (400–700 mJ). The results revealed a crystalline size of 65.90 nm and 86.55 nm at 700 mJ, while the size was 40.19 nm and 17.19 at 400 mJ for the given wavelengths

This study investigates the influence of silver oxide (Ag₂O) concentration on the optical characteristics of phosphate bioactive glasses (PBGs). PBGs have emerged as promising alternatives to conventional silicate glasses in the medical field due to their excellent bioactivity and chemical resistance. Samples with varying Ag₂O concentrations (0, 0.25, 0.5, and 0.75g) were sintered at 780°C for 2 hrs in an electric furnace. The samples were subjected to Fourier transfer infrared spectroscopy (FTIR), ultraviolet-visible (UV-Vis) spectroscopy, and photoluminescence (PL) tests to assess their functional groups and optical properties. By analyzing the FTIR spectrum of phosphate bioactive glass containing different amoun

In the present work, pulsed laser deposition (PLD) technique was applied to a pellet of Chromium Oxide (99.999% pure) with 2.5 cm diameter and 3 mm thickness at a pressure of 5 Tons using a Hydraulic piston. The films were deposited using Nd: YAG laser λ= (4664) nm at 600 mJ and 400 number of shot on a glass substrate, The thickness of the film was (107 nm). Structural and morphological analysis showed that the films started to crystallize at annealing temperature greater than 400 oC. Absorbance and transmittance spectra were recorded in the wavelength range (300-
4400) nm before and after annealing. The effects of annealing temperature on absorption coefficient, refractive index, extinction coefficient, real and imaginary parts of d

Zinc sulfide (ZnS) thin films were deposited on glass substrates using pulsed laser deposition technique. The laser used is the Q-switched Nd: YAG laser with 1064nm wavelength and 1Hz pulse repetition rate and varying laser energy 700mJ-1000mJ with 25 pulse. The substrate temperature was kept constant at 100°C. The structural, morphological and optical properties of ZnS thin films were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscope (AFM) and UV-VIS spectrophotometer.

A simulated perovskite solar cell based on a P3HT/MAPbI3/C60 structure is examined to achieve 30% PCE using SCAPS-1D software. Several aspects of the perovskite layer were evaluated, including the perovskite layer thickness, CB and VB effective density of state, band gap, and electron affinity. These factors show great influence on the device performance. The best device based on the best examined parameter has exhibited a PCE of 32.1% correlated with FF of 84.8%, V_OC of 1.23V and J_SC of 30.77 mA.cm^-2. Such a result is promising towards achieving high PCE for perovskite-based solar cells by optimizing several factors, including active layer thickness, energy band gap, electron affinity, and effective stat

Understanding the CNO cycle and the proton-proton (p-p) chain is essential for comprehending the development of main sequence stars in the initial stages of spiral and elliptical galaxy formation. This study investigates two nuclear reactions that occur in spiral galaxies and elliptical galaxies. Using theoretical computer software (e.g. OriginPro. software program), we summarized the excitation functions to analyze the (p,γ) interaction cross sections of 7Be(p,γ)8B, 12C(p,γ)13N, 14N(p,γ)15O, and 15N(p, γ)12C. In the p-p series and CNO cycle with energy up to 8 MeV. In this work, we compared the theoretical values from the ENDF/B-VII library with the estimated database of nuclear fusion cross sections in hydrogen-burning stellar obj

Evapotranspiration is considered an essential element for the stability of the ecosystem due to its importance in many aspects, including the water cycle, which is an important source of fresh water for humans, animals and plants. It also influences climate and temperatures and regulates weather. It also enters into the design of crop irrigation networks, knowing their water needs to prevent drought and desertification. The Penman-Monteith method is effective and accurate for calculating daily reference evapotranspiration and has been adopted by the Food and Agriculture Organization (FAO) as a standard method. This study aims to calculate the variation in evapotranspiration rates in Iraq using the Penman-Monteith method over the past thi

IIn this work, carboxymethyl cellulose/polyanionic cellulose (CMC HV/PAC LV) films were prepared and exposed to different X-ray doses (0, 200, 400, 600 and 800 cGy). Absorption and transmission measurements of the ultraviolet spectrum of the incident light were studied with a DU 800 spectrophotometer. Stress and strain were calculated by applying a tensile force to the samples and increasing its amplitude until the sample breaks. Applying this force to the samples increased the length of the samples. The absorption of CMC HV/PAC LV films increased with increasing X-ray dose, and therefore, the absorption coefficient increased with increasing X-ray dose. The results show that the amount of spectral transmittance of the films decreased wit

Polyaniline (PANI) and manganese dioxide (MnO2) doped with nickel oxide (NiO) nanocomposite have emerged as promising materials for gas sensing applications due to their high conductivity and surface area. This study improves the synthesized PANI/MnO₂:NiO nanocomposites' sensitivity towards NO₂ gas. Atomic force microscopy (AFM), Fourier transfer infrared (FTIR), scanning electron microscopy (SEM), energy-dispersive X-ray analysis (EDS), and X-ray diffraction (XRD) were used to analyze the produced nanocomposites. More precise methods were investigated to identify problems associated with oxidation, corrosion and sensor activity, such as increasing the amount of added nickel oxide, changing the structure of nanocomp

In this work, we studied the effect of power variation ​​on inductively coupled plasma parameters using numerical simulation. Different values ​​were used for input power (750 W-1500 W), gas temperature 300K, gas pressure (0.02torr),         5 tourns of the copper coil and the plasma was produced at radio frequency (RF) 13.56 MHZ on the coil above the quartz chamber. For the previous purpose, a computer simulation in two dimensions axisymmetric, based on finite element method, was implemented for argon plasma. Based on the results we were able to obtain plasma with a higher density, which was represented by obtaining the plasma parameters (electron density, electric potential, total power, number density of argon ions, el

Gold nanoparticles AuNPs have proven to be powerful tools in various nanomedicine applications, because of their photo-optical distinctiveness and biocompatibility. Noble metal gold nanoparticles was prepared by pulsed laser ablation method (1064-Nd: YAG with various Laser power from 200 to 800 mJ and 1 Hz frequency) in distil water. The process was characterized using UV-VIS absorption spectroscopy. Morphology and average size of nanoparticles were estimated using AFM and X-ray diffraction (XRD) analysis which show the nature of gold nanoparticles (AuNPs). Antibacterial activity of gold nanoparticles as a function of particles concentration against gram negative bacterium Escherichia coli and gram positive bacterial Staphylococcus aureu

The neutron flux in this paper, which is generated as a result of γ incineration of the radioactive fisssion products isotopes has been evaluated .It is obvious from this paper that the neutron flux value depends on the number of incineration nuclei and the nuclear cross-section of the incinerated isotopes, and the neutron flux is directly dependent on γ-ray flux. The neutron flux increases from 1010to 1017n/s.gm as the irradiation flux increases from 1016to 1020 γ/cm2.s. It is concluded that the γ-incineration technique can be used to produce a switchable neutron source of high flux.

The Gaussian orthogonal ensemble (GOE) version of the random matrix theory (RMT) has been used to study the level density following up the proton interaction with ⁴⁴Ca, ⁴⁸Ti and ⁵⁶Fe.

A promising analysis method has been implemented based on the available data of the resonance spacing, where widths are associated with Porter Thomas distribution. The calculated level density for the compound nuclei ⁴⁵Sc,⁴⁹Vand ⁵⁷Co shows a parity and spin dependence, where for Sc a discrepancy in level density distinguished from this analysis probably due to the spin  misassignment .The present results show an acceptable agreement with the combinatorial method of level density.

In this work, a pulsed Nd:YAG laser(out put energy=5J and pulse
duration=300μsec) was used to perform drilling in samples of lead, stainless steel
304, brass, copper and aluminum. Laser irradiation was carried out in both air and
in a suitable chamber of controlled pressure inside. The effect of pressure inside the
chamber on the drilling process was investigated. Then, the chamber was filled with
argon gas to investigate its effect on drilling process where an enhancement in
drilling depth was observed compared to that in case of irradiation in air and
chamber of air pressure. As well, the effect of focus position on the process was
studied with the pressure varying inside the chamber in order to construct a

In this work, the properties of the photodetector were improved by using carbon quantum dots (CQDs) and tris (8-hydroxyquinoline) aluminium (III) (Alq3) polymer when deposited on glass and silicon substrates. CQDs were prepared using an electrochemical method. Two methods of deposition were used; the first was drop casting, and the other was spin coating. The structural, electrical, and optical properties were studied. Measurements were made of the manufactured photoconductive detector's current-voltage (I–V) properties, photocurrent gain, response time, and quantum efficiency, responsivity. The constructed detector's performance was measured without light and using a 250-watt tungsten lamp, whose wavelength range was between 500 and 8

In the present work, radon gas concentrations in different surface soil samples in Baghdad governorate were measured using RAD-7 detector. The results have been shown that, the Radon gas concentrations ranged between (41.67±1.78Bq/m3), to (185.67±4.22Bq/m3), a map showing the distribution of the concentration of radon in selected areas was defined to identify areas with high pollution level. The reason for the high concentration of radon is that these surface soil samples are taken from agricultural areas. It is also known that fertilizers contain uranium levels as well as areas bombed in wars in the country. It is worth noting that all radon concentrations in Baghdad governorate are below the recommended minimum of 200-300Bq/m3) (Inte

The state and partial level densities were calculated using the corresponding formulas that are obtained in the frame work of the exciton model with equidistant spacing model (ESM) and non-ESM (NESM). Different corrections have been considered, which are obtained from other nuclear principles or models. These corrections are Pauli Exclusion Principle, surface effect, pairing effect, back shift due to shell effect and bound state effect . They are combined together in a composite formula with the intention to reach the final formula. One-component system at energies less than 100 MeV and mass number range (50-200) is assumed in the present work. It was found that Williams, plus spin formula is the most effective approach to the composite

This work investigates the utilization of waste papers (natural and industrial) i.e (citrus aurantium and papers A4) mortars containing specified contents 0.5%, 1%, 1.5% of waste papers were prepared and cured. Mechanical characteristics such as compressive and bending strengths, hardness and water absorption were determined for the mortars mixed with the waste papers and compared with those obtained from the pure mortars. Results showed that the addition of waste paper leads to increase the hardness to (69 - 68.5) shore D for (natural and industrial) wastes materials respectively comparing with pure specimen 66 shore D. The compressed strength of the mortar cement specimen cured for 28 days from 13 MPa to (17-18) MPa for (natural and in

The influences of the Cu substitution at Hg site in the HgOd layer, upon the
microstructure, Tc and oxygen content of Hg-1223 have been investigated. High
temperature superconductor with a nominal composition Hg1-xCuxBa2Ca2Cu3O8 + δ for
Cu ( 0 £ x £ 0.5) have been prepared by the two-steps solid state reaction method
under optimum conditions. XRD showed a tetragonal structure with a high ratio of
Hg-1223 superconductor phase. Tc enhancement has been determined with the Cu
concentration was is found to be Tc = 153 K for x = 0.3, while the oxygen content
observed variously with Cu concentration. Hg1-xCuxBa2Ca2Cu3O8+δ structure, oxygen
content and Tc behavior have been discussed.